Detox1

phroze

Detox1
Hi. Please don't tell me I have to reinstall windows for this to work. I did a reinstall earlier this month.

 

I'd reinstall and get away from the BIOS style installation and move to UEFI. This is a BIOS setting. Here are some reasons and explanations
 

Thanks for the link & quick response. I'll have to think if it's worth the hassle, just for this one feature.

You're welcome. That and if you ever want a large hard drive or SSD you'll need to go UEFI.

I just tried flashing my wife's 3060ti XC. It appeared to flash successfully and the command line asked me to reboot. It now will not boot, and the motherboard displays a red light on the GPU boot code.

I previously had successfully flashed my Asus 3080 to ReBAR. I tried the EVGA card on my system as it definitely boots with ReBAR. It also gave the GPU light. I tried putting the 3060ti as my secondary card, in hopes I could boot on my 3080 and reflash it, but the system still refused to boot with a red light. Bios is in UEFI mode, etc.

Azuroth

phroze

gt5759

Detox1

phroze

Detox1
Hi. Please don't tell me I have to reinstall windows for this to work. I did a reinstall earlier this month.

 

I'd reinstall and get away from the BIOS style installation and move to UEFI. This is a BIOS setting. Here are some reasons and explanations
 

Thanks for the link & quick response. I'll have to think if it's worth the hassle, just for this one feature.

google mbr2gpt conversion

I have successfully done that in the past.

Just did it myself, from an admin command prompt:
mbr2gpt /validate /allowFullOS
if it says everything is good
mbr2gpt /convert /allowFullOS
 
When I rebooted after updating my bios to stop using CSM and turn on resizable bar, I did need to run:
reagentc /enable
 
whole process took about two minutes.
 

Awesome! I remember having to do it back when UEFI was a pretty new thing. Glad it's working for you, I have the same mobo ;)

Looks like everything is working with the BAR, but GPU fans are all messed up again with the new PrecisionX1 version (as always). On auto settings fans won't go below 37% and on manual minimum is 33% for fans 1 & 2.

ReBar works, but after installing Precision X1 and updating the VBIOS I also have the problem with the new minimum fan speed, which completely ruins it.
Before that I had only the Afterburner installed and where running at 0 fan speed in normal (office) mode.
Can you fix this please?
 
3080 FTW3 Ultra

Did anyone found a solution for when you have more than 1 card in the system? Precision wont let me select my secondary 3070 to update the Vbios

Hi everyone,
 
My setup: Asus Strix B550-F with 1804 bios, AMD Ryzen 5 5600X with 32 GB Ram and RTX 3060 Ti FTW3 Ultra.
 
I downloaded the latest version of Precision and had a notice to update the card. Updated. I opened Precision and in the ReSize Bar tab, there was a notification to update the vbios.
 
I clicked and at the prompt I pressed Y to continue. It was and another screen appeared to press Y. I pressed and then there was an error that did not update. My PC has restarted and the card connects the leds and fans, but there is no video signal.
 
I connected the card to another PC and it also does not provide video.
 
I took my ex GTX 1070 FTW and put it on my PC, and it gave video.
Did I lose the VGA? :( :( :( :(

Boot up on the normal bios and the led screen on the KP still says Firmware update, nothing else, great stuff.
 

EVGA_JacobF

agar534986

 
What should I do at this point? Too scared to reboot.

Can you try to flash again?

That was the problem that happened here, but my Windows ended up restarting afterwards. :(
 
And now my VGA no shows signs of life :( :( :( :(

memnon8711
I wonder if this is an issue with Asus motherboards and the fact they have Resizable BAR set as an Auto option to enable it.  Maybe Precision X1 can't pick up Auto and the fact Resizable BAR is turned on for the motherboard.  I have same issue with a Prime x470 with a Ryzen 3600 installed.  NVidia Control Panel and GPU-Z show Resizable BAR is enabled though. 

I don't think so. I'm on Intel but Z490 and it worked flawlessly. 

EVGA_JacobF

InfusionOfFear

EVGA_JacobF
Try a complete power off (flip off PSU switch) and boot up on OC side.

 
Hi, I just followed those steps, and still no video on the OC bios side. Connected via HDMI if that matters (only have 1 monitor connected).

Sending DM

I have experienced the same issue. I have since found a few workarounds and am no longer experiencing this issue, however, I would like to know if there is any surefire fix since the problem appears to have gone away on its own and I don't know if/when it might come back.

Campacci2k

phroze

Campacci2k

EVGA_JacobF

agar534986

 
What should I do at this point? Too scared to reboot.

Can you try to flash again?

That was the problem that happened here, but my Windows ended up restarting afterwards. :(
 
And now my VGA no shows signs of life :( :( :( :(

If you have no display out and are completely stuck you can try to boot from the integrated graphics or another card while the borked card is installed too. Then flash the BIOS. If it's a dual BIOS card you can switch to the bad BIOS while booted into windows then flash

I'll try this tomorrow! My second PC have a integrated graphics.
 
For me to flash using another card, my card that is not showing any sign of life needs to have all the power connectors plugged in? How will I do the flash without it being "identified" by Windows?

There's a good chance that windows still recognizes it but it is not showing a display. Here's an old post that may help you out. Look for the user TK's post.
 
https://forums.guru3d.com...od-help-needed.364224/

Campacci2k
Thanks @phroze. Where I find bios for 08G-P5-3667-KR?
 
I'll try this tomorrow.
 
 

You're welcome. Techpowerup keeps a repository of VBIOS. It's not the new BIOS. Should be the original.
https://www.techpowerup.c...-rtx3060ti-8192-201028

Need the new 10G-P5-3885-KR bios.

Precision X1 bricked my card. Good stuff here

I would suggest people run some benchmarks.  This is definitely not a performance boost on my end. After the update I took a sizable loss in performance. And flashing back to prior bios does not help. I believe it updated the firmware and borked our performance.