bbevgacard
New Member
- Total Posts : 20
- Reward points : 0
- Joined: 2021/02/14 06:26:03
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/15 15:04:22
(permalink)
Had same thing happen to mine without 1000w bios. No luck on replacement from evga or help from them really. A schematic or whatever smd mine was would have been nice. Learning how to solder 😂
|
telehog
iCX Member
- Total Posts : 413
- Reward points : 0
- Joined: 2018/12/05 13:48:52
- Status: offline
- Ribbons : 1
Re: RTX 3090 Kingpin Hydrocopper
2021/05/15 16:22:58
(permalink)
 Robotic surface mounted mother board were never meant to be repaired, but to replace. I have the right tools, don't have good eyes and steady hands. Ill run some test and isolate the problem. Should be something simple that I damaged on tare down. No hot spots on board . Then if you can get the right smd ,Ill give it a go . 
post edited by telehog - 2021/05/15 16:26:32
Attached Image(s)
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/16 07:53:14
(permalink)
you said it doesnt show any lights at all?
did you try different power cables, PCIE slot on mobo?
You could also try putting AIO back on and see if it works then
|
telehog
iCX Member
- Total Posts : 413
- Reward points : 0
- Joined: 2018/12/05 13:48:52
- Status: offline
- Ribbons : 1
Re: RTX 3090 Kingpin Hydrocopper
2021/05/16 14:09:59
(permalink)
CptT95
you said it doesnt show any lights at all?
did you try different power cables, PCIE slot on mobo?
You could also try putting AIO back on and see if it works then
No light at all < try different Pcie slots, psu, power cables and riser cable. I did not put AIO back on because I did not think it would help, unless it put pressure on something that came lose. I put power to Gpu naked also with no luck. I need to get multi - meter out and do continuity checks. Hope its not a broken trace, when you tare card down that double sided foam tape pad takes a lot of force to break free. I thought I had miss a screw it took so much force .
|
Dabadger84
CLASSIFIED Member
- Total Posts : 3426
- Reward points : 0
- Joined: 2018/05/11 23:49:52
- Location: de_Overpass, USA
- Status: offline
- Ribbons : 10
Re: RTX 3090 Kingpin Hydrocopper
2021/05/16 20:11:50
(permalink)
telehog
CptT95
you said it doesnt show any lights at all?
did you try different power cables, PCIE slot on mobo?
You could also try putting AIO back on and see if it works then
No light at all < try different Pcie slots, psu, power cables and riser cable. I did not put AIO back on because I did not think it would help, unless it put pressure on something that came lose. I put power to Gpu naked also with no luck. I need to get multi - meter out and do continuity checks. Hope its not a broken trace, when you tare card down that double sided foam tape pad takes a lot of force to break free. I thought I had miss a screw it took so much force .
Yeah that double sided tape near the OLED corner of the backplate is a serious P-I-T-A. I took mine off of the card completely. I think I'm going to end up using thermal tape to fix that & the other pressure issue I've noticed with my backplate, which is the HydroCopper block making one of the backplate screws not be used so part of the left side is loose too.
ModRigs: https://www.modsrigs.com/detail.aspx?BuildID=42891 Specs:5950x @ 4.7GHz 1.3V - Asus Crosshair VIII Hero - eVGA 1200W P2 - 4x8GB G.Skill Trident Z Royal Silver @ 3800 CL14Gigabyte RTX 4090 Gaming OC w/ Core: 2850MHz @ 1000mV, Mem: +1500MHz - Samsung Odyssey G9 49" Super-Ultrawide 240Hz Monitor
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/17 15:59:17
(permalink)
Hey Badg, you should probably update your sig for ram change, also I think I have a solution to my pump tach reading dying, I am planning twin loops once I am finished, so I think I will just run both pumps off one fan header with a splitter, so that my second pump will feed mobo rpm signal, while mobo will send PWM to both pumps
seriously peeved that I somehow screwed up a 130 dollar pump lol, this one I picked cause of the sleeved cables coming out of the pump (primochill branded)
|
Gotspeed_2000
SSC Member
- Total Posts : 818
- Reward points : 0
- Joined: 2021/01/07 18:53:17
- Status: offline
- Ribbons : 5
Re: RTX 3090 Kingpin Hydrocopper
2021/05/17 16:33:56
(permalink)
CptT95
Hey Badg, you should probably update your sig for ram change, also I think I have a solution to my pump tach reading dying, I am planning twin loops once I am finished, so I think I will just run both pumps off one fan header with a splitter, so that my second pump will feed mobo rpm signal, while mobo will send PWM to both pumps
seriously peeved that I somehow screwed up a 130 dollar pump lol, this one I picked cause of the sleeved cables coming out of the pump (primochill branded)
Some pumps allow you to direct connect it to the psu making the pump run at max speed. If you have this option I would look at that but it depends on the pump. You will lose the ability to control the flow of the pump, but it will work and not impact your mobo in any way. You could always get a in-line flow meter to gauge the flow rate of that loop if needed. I would recommend checking your mobo specs as I thought that the pumps draw more power (especially D5s) than fans so that is why some mobos have dedicated pump headers or high amp pump headers. It will also depend on what pumps you are using like dual D5s or DDC pumps, etc. Splitting those headers might not be within the mobo specs as far as amp draw so this might be of concern depending on your mobo. I think gigabyte has some flexibility built into some of their motherboards to allow you to use either pumps or fans on certain headers but they are still limited by amp rating individually. Most other brands have dedicated fan ports and/or dedicated pump ports depending on the features of the boards. I know some people use the fan ports when they plug in AIOs, but those draw less power from my understanding which is why they can get away with it. Putting two high draw components together in one port would concern me enough to research the specs of your board first.
Corsair 1000D Obsidian Case I9 13900K with EK Velocity 2 Block ASUS 4090 Strix with Optimus Block ASUS Hero Z690 Mobo 64GB DDR5 RAM Trident 6000Mhz 1TB Nvme primary /2*2TB Nvme secondary/1tb & 2TB SSD drive EVGA 1600 Watt PSU 30 Lian Li AL120 fans 2 * 480mm medium thickness rad, 2 * 360mm medium thickness rad, with Two EK Pump/res combos. Custom hard tube loop. Samsung G7 32" Monitor EVGA Z20 Keyboard Glorious Model O
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/17 21:51:33
(permalink)
Gotspeed_2000
CptT95
Hey Badg, you should probably update your sig for ram change, also I think I have a solution to my pump tach reading dying, I am planning twin loops once I am finished, so I think I will just run both pumps off one fan header with a splitter, so that my second pump will feed mobo rpm signal, while mobo will send PWM to both pumps
seriously peeved that I somehow screwed up a 130 dollar pump lol, this one I picked cause of the sleeved cables coming out of the pump (primochill branded)
Some pumps allow you to direct connect it to the psu making the pump run at max speed. If you have this option I would look at that but it depends on the pump. You will lose the ability to control the flow of the pump, but it will work and not impact your mobo in any way. You could always get a in-line flow meter to gauge the flow rate of that loop if needed.
I would recommend checking your mobo specs as I thought that the pumps draw more power (especially D5s) than fans so that is why some mobos have dedicated pump headers or high amp pump headers. It will also depend on what pumps you are using like dual D5s or DDC pumps, etc. Splitting those headers might not be within the mobo specs as far as amp draw so this might be of concern depending on your mobo. I think gigabyte has some flexibility built into some of their motherboards to allow you to use either pumps or fans on certain headers but they are still limited by amp rating individually. Most other brands have dedicated fan ports and/or dedicated pump ports depending on the features of the boards.
I know some people use the fan ports when they plug in AIOs, but those draw less power from my understanding which is why they can get away with it. Putting two high draw components together in one port would concern me enough to research the specs of your board first.
I have a d5 pump, which I think I mentioned before, and those always have dedicated Sata/Molex power plug and a 4 pin fan plug with only the PWM and tach wires used(12v+ and ground are left open/blank)
|
Dabadger84
CLASSIFIED Member
- Total Posts : 3426
- Reward points : 0
- Joined: 2018/05/11 23:49:52
- Location: de_Overpass, USA
- Status: offline
- Ribbons : 10
Re: RTX 3090 Kingpin Hydrocopper
2021/05/17 23:43:09
(permalink)
CptT95
Hey Badg, you should probably update your sig for ram change, also I think I have a solution to my pump tach reading dying, I am planning twin loops once I am finished, so I think I will just run both pumps off one fan header with a splitter, so that my second pump will feed mobo rpm signal, while mobo will send PWM to both pumps
seriously peeved that I somehow screwed up a 130 dollar pump lol, this one I picked cause of the sleeved cables coming out of the pump (primochill branded)
Eh, I'm not gonna bother updating it until I get the new kit in, then it'll be 4x8GB 4000MHz CL15 @ whatever I can get it to run at... probably 3800MHz CL14. I am so glad my pump doesn't have one of those dials like my loop way back in the day did that you have to change with a flat-tip screw driver, much prefer this EK pump's method of control by PWM signal.
ModRigs: https://www.modsrigs.com/detail.aspx?BuildID=42891 Specs:5950x @ 4.7GHz 1.3V - Asus Crosshair VIII Hero - eVGA 1200W P2 - 4x8GB G.Skill Trident Z Royal Silver @ 3800 CL14Gigabyte RTX 4090 Gaming OC w/ Core: 2850MHz @ 1000mV, Mem: +1500MHz - Samsung Odyssey G9 49" Super-Ultrawide 240Hz Monitor
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/18 15:14:02
(permalink)
Looking forward to the KP Hybrid hitting 2021 time stamps lol
|
Cjdowd80
Superclocked Member
- Total Posts : 130
- Reward points : 0
- Joined: 2019/11/10 15:52:17
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/19 07:39:26
(permalink)
Hey all, so i just got my HC kit in, and installed into my loop yesterday .. got a random question. In PX1, everything is reading correctly, and can adjust and reflecting in sensor panel, however, the OLED on the KPE is showing 1920MHz only, and I cannot change it in PX1, nor can I shut it off. Anyone have any ideas or had similar problems?
Associate Code: HLZG20V1ZF4SZGW AMD Ryzen 9 5950x - Asus ROG Crosshair VIII Formula - 32gb (4x8gb) @3600 CL16 GSkill Trident Z NEO - EVGA RTX 3090 Kingpin - Corsair RMx 1000w 80+ Gold - Lian Li O11 Dynamic XL - EK 360mm AIO
|
Dabadger84
CLASSIFIED Member
- Total Posts : 3426
- Reward points : 0
- Joined: 2018/05/11 23:49:52
- Location: de_Overpass, USA
- Status: offline
- Ribbons : 10
Re: RTX 3090 Kingpin Hydrocopper
2021/05/19 08:21:48
(permalink)
Cjdowd80
Hey all, so i just got my HC kit in, and installed into my loop yesterday .. got a random question. In PX1, everything is reading correctly, and can adjust and reflecting in sensor panel, however, the OLED on the KPE is showing 1920MHz only, and I cannot change it in PX1, nor can I shut it off. Anyone have any ideas or had similar problems?
So the OLED is frozen in effect? Try reinstalling Precision, and if you took the OLED screen off during the HydroCopper block install, try taking the OLED off completely, unplugging it & plugging it back in (with the computer off of course). It's possible one of the connections on the plug has a bad seat and that might fix it.
ModRigs: https://www.modsrigs.com/detail.aspx?BuildID=42891 Specs:5950x @ 4.7GHz 1.3V - Asus Crosshair VIII Hero - eVGA 1200W P2 - 4x8GB G.Skill Trident Z Royal Silver @ 3800 CL14Gigabyte RTX 4090 Gaming OC w/ Core: 2850MHz @ 1000mV, Mem: +1500MHz - Samsung Odyssey G9 49" Super-Ultrawide 240Hz Monitor
|
pureenergie
New Member
- Total Posts : 57
- Reward points : 0
- Joined: 2009/02/08 20:36:34
- Status: offline
- Ribbons : 2
Re: RTX 3090 Kingpin Hydrocopper
2021/05/22 20:29:14
(permalink)
Did the full prebuilt hydrocopper go on sale yet? I see it on website but no auto notify
|
Ericthegreat
Superclocked Member
- Total Posts : 147
- Reward points : 0
- Joined: 2015/09/07 17:58:30
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/22 20:40:02
(permalink)
It was on notify for 18ish seconds.
|
garbage-79
New Member
- Total Posts : 100
- Reward points : 0
- Joined: 2021/05/25 00:59:03
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/25 08:10:26
(permalink)
Any idea when this will be restocked again?
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/25 16:57:47
(permalink)
Its still working through launch mini-queue, when this small queue is finished it will go up for notify again
|
GP300
Superclocked Member
- Total Posts : 165
- Reward points : 0
- Joined: 2013/01/09 18:12:44
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/28 09:55:27
(permalink)
Anyone know the tubing size for the Kingpin 3090 Hydrocopper?
Thanks
  Please register your products with my code and don't forget to upload your invoice, Thanks! VUUI8XCYCI 
|
flyingtoaster85
iCX Member
- Total Posts : 282
- Reward points : 0
- Joined: 2016/12/10 22:24:59
- Location: Los Angeles
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/28 10:44:27
(permalink)
GP300
Anyone know the tubing size for the Kingpin 3090 Hydrocopper?
Thanks
The block has 1/4 inch female threads that work with any male fitting. The barb size on the fitting is what you need to match with the inner diameter of your tubing.
Main: 10700k @ 5.4ghz, 3090 K|NGP|N Hydrocopper, 4x8 @4300 16-16-16-36, EVGA 1200 P2, MSI Z490 Unify, 5 radiators, 2 pumps. Heavily modified Evolv ATX Travel size: Zen3 5800H, RTX 3060 Laptop GPU w/unlocked bios, 2x16 Kingston HyperX 3200 C20
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/05/28 18:45:04
(permalink)
flyingtoaster85
GP300
Anyone know the tubing size for the Kingpin 3090 Hydrocopper?
Thanks
The block has 1/4 inch female threads that work with any male fitting. The barb size on the fitting is what you need to match with the inner diameter of your tubing.
got enough radiators in your main rig XD mind posting pics of setup?
|
babayega
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2020/07/30 08:18:30
- Status: offline
- Ribbons : 1
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 03:21:07
(permalink)
does anyone know the thermal pad thickness for the hydrocopper block(kingpin) , both front side and back side.is it 2mm?
|
degenerate
SSC Member
- Total Posts : 614
- Reward points : 0
- Joined: 2013/08/23 05:38:31
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 04:17:42
(permalink)
babayega
does anyone know the thermal pad thickness for the hydrocopper block(kingpin) , both front side and back side.is it 2mm?
2.25mm for memory, 2.75mm for mosfets, 2.5mm for backplate.
 |5900x|MSI B550 Unify-X|2x16GB G.Skill 3800 C14 @ 1900 FCLK|2TB WD SN850 M.2|EVGA 3090 KPE|EVGA 1600T2|Alienware '25' & LG 48" CX OLED|
|
babayega
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2020/07/30 08:18:30
- Status: offline
- Ribbons : 1
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 05:05:24
(permalink)
okay but thats the thermal pad evga use, and those pads are insanely soft, so does anyone know like the height between the memory module to backplate and mem module to front wb.
|
degenerate
SSC Member
- Total Posts : 614
- Reward points : 0
- Joined: 2013/08/23 05:38:31
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 05:14:06
(permalink)
Disassemble it and measure yourself.
|5900x|MSI B550 Unify-X|2x16GB G.Skill 3800 C14 @ 1900 FCLK|2TB WD SN850 M.2|EVGA 3090 KPE|EVGA 1600T2|Alienware '25' & LG 48" CX OLED|
|
GP300
Superclocked Member
- Total Posts : 165
- Reward points : 0
- Joined: 2013/01/09 18:12:44
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 12:16:15
(permalink)
Just got my Kingpin Hydrocopper and I've got to say I wasn't expecting it to weight quite as much as it does! Is it recommended to use some type of vertical support "beam" ? Question 2...should I change the thermal pads or are they "better" than the regular 3090 FTW3 pads in either quality or placement?
Thanks in advance!
Please register your products with my code and don't forget to upload your invoice, Thanks! VUUI8XCYCI
|
Fayalite
iCX Member
- Total Posts : 253
- Reward points : 0
- Joined: 2021/01/08 18:38:42
- Location: Bellevue, WA
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 12:17:05
(permalink)
degenerate
Disassemble it and measure yourself.
Â
Most useless community support... Someone asking this is to be able to still use it while ordering, when others already have the answer. It is fine to ask, if you don't want to answer just don't be sour.
|
Fayalite
iCX Member
- Total Posts : 253
- Reward points : 0
- Joined: 2021/01/08 18:38:42
- Location: Bellevue, WA
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 12:17:05
(permalink)
|
Redrum187
New Member
- Total Posts : 13
- Reward points : 0
- Joined: 2021/06/10 12:12:52
- Status: offline
- Ribbons : 0
Flagged as Spam (2)
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 12:21:56
(permalink)
This looks like a great gpu
|
Professormidnight
New Member
- Total Posts : 8
- Reward points : 0
- Joined: 2021/06/10 12:18:27
- Status: offline
- Ribbons : 0
Flagged as Spam (2)
Re: RTX 3090 Kingpin Hydrocopper
2021/06/10 12:27:38
(permalink)
I would get a support. I have one for my 1080 hybrid. It will make a world of difference, and give you piece of mind. I got my on Amazon
|
CptT95
FTW Member
- Total Posts : 1403
- Reward points : 0
- Joined: 2016/12/31 23:06:26
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/11 17:00:40
(permalink)
babayega
does anyone know the thermal pad thickness for the hydrocopper block(kingpin) , both front side and back side.is it 2mm?
https://forums.evga.com/3090-Kingpin-amp-others-Get-that-backside-VRAM-cool-m3219773-p38.aspxgo to this thread and look through the latest 5 pages or so, or if you feel like it go to the beginning and see what Dabadger posted about replacing thermal pads, think the main pads were 2mm and the rest were not as important to replace, unless they come apart with the card lol tech posted exact measurements recently in that thread so take that and round the thickness down to nearest .5mm or .00mm Edit- the HC does NOT need a brace; the block itself is extremely sturdy, despite its weight it has absolutely no give once mounted I can grab the card by the end and wiggle it and my whole PC moves while the card doesn't budge, and my pc weighs a ton now lol
post edited by CptT95 - 2021/06/11 17:03:13
|
Fayalite
iCX Member
- Total Posts : 253
- Reward points : 0
- Joined: 2021/01/08 18:38:42
- Location: Bellevue, WA
- Status: offline
- Ribbons : 0
Re: RTX 3090 Kingpin Hydrocopper
2021/06/11 19:41:07
(permalink)
Mesh... I still added a support tube (16mm hard tube cut to keep it straight... Just for my OCD
|