In the meantime, I upload a photo of a power supply that will be used in one .... maybe two projects;)
EVGA SuperNOVA G3 1000 W.
 

 

 

 

 

 

Wow.... Talk about detail!!!!!

For a long time I do not have a desk, table ...... in general no convenient position, where I can comfortably use the laptop.
Watching the desks in stores, with the budget (about 700zł), unfortunately none of my requirements. Something was missing.
So I decided to build them myself, from scratch, the ones I want and which allow me finance.
 
Required items ordered, delivered:
 

 

 
One of two worktops - 160cm x 75cm x 3.8cm


 
Wood for supports and cable troughs.


 
Dimension
 

 
We cut to the dimension.


 

 
We sharpen the sharp edges.


 
We drill holes for screws.


 

 

 
Supports ready.



Now we will deal with the top.


 
We will mark where will be the supports, LED profiles and cable troughs.


 
The place under the trough milled - the deck is quite thick and can be trough into it, so it will not stand still (though it will not be visible anyway).


 

 
The trough slightly protrudes, so in the supports it was necessary to maneuver a place on this protruding part of the trough.

I hope you will be interested.
Simple, relatively fast construction desk at a relatively small cost.
 
Troughs for LED profiles made.
 

 
... and additional cables.
 

 
Backlighting of the desk:
 
The easiest solution is to stick the tape itself to the back of the tabletop, to bring it to the wall and ready.
 

 
but
 

 
I want to have no distance between the wall and the tabletop and the backlight does not go down and up simultaneously.
From below, the countertop will be illuminated only on the front and on the sides, while the rear LED strap is to throw light only upward, but not to blind, so I decided to use an angular profile.
 

 
We dump the place for him.
 

 
Really judge.
 

 

 
We will arm the cap.
 

 
Somehow it came out.
 

 
LED profiles from below.
 
After making the channels on the trousers LED profiles, time to cut and trim them.
Their angular joints are not easy to do - the cut itself lasted a few seconds, measuring a few minutes.
 

 
At the end of the place insert a plug.
 

 


Short section of the second top.
 


Other electrics / electronics, box cable management.
 

 
Fast connection and test (if it works).
 

Thank you very much.
 
Little bonus :)
 
SKEEPER & EVGA GARAGE :)
 

 

 

This is looking really good

Looks like you have a lot of work ahead of you on this part of your project.

Thanks! :)
I thought I would do it all over, but unfortunately it is not.
Fortunately 70% of the work is already done.
The desk itself is so presentable.
 

 

 

 

 

 

 

 
 
 
 

Looks great. Well done.

 

 

 

 

 

 

 

I refresh the topic.
 
IFA Berlin is already behind us. Until then, I had to put the computers together and lack the time to publish the material.
There are already pictures of ready-made screenshots - here we will develop some.
 
So let's continue the EVGA DG-87 setup.
The housing, graphics card and motherboard was presented, so now AiO.
The processor will cool the EVGA CLC-280
 

 


 

 

 

 


 
 The unit will power the previously presented EVGA SuperNOVA G3 1000W.

rjohnson, thank you for the warm welcome.
 
This project and Aorus was released on the launch of the new M.2 / PCI SSDs and Goodram's RAM memory of 3000MHz.
For the EVGA flew DDR4 3000MHz 64GB (8x8) frame - brushed aluminum.
 

 

 

 
Two 240GB SSD M.2 drives - one in M.2, one in PCI
 

 
Two 480GB SATA SSDs
 

 
The last thing is the cables - the full set was made by my colleague Patryk - MisterT.Design (I have no patience for them).
 

Thank you.
 
Keeping a certain amount of chronology in the topic, it was time to present the entire computer.
Specification:
CASE - EVGA DG-87
MOBO - EVGA x99 FTW K
GPU - 2-way SLI EVGA GeForce 1080 FTW2 DT GAMING
SSD - 2 x GOODRAM IRIDIUM PRO 480 GB
SSD - GOODRAM IRDM ULTIMATE PCI-e 2280 240 GB
SSD - GOODRAM IRDM ULTIMATE M.2 2280 240GB
RAM - GOODRAM IRIDIUM DDR4 3000 MHz 64 GB (8 x 8)
PSU - EVGA SuperNOVA 1000 G3
CPU cooler: AiO EVGA CLC 280
ALPHACOOL LED PANEL - BIAŁY

 

 

 

 

 

 

 

 

 

 

 

 

 

Absolutely awesome. I wish I had your skills. 

cabofreak
outstanding, your build log is gorgeous as well as the finished build, great job

Yes he has really great skills