mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
I built this Windows 7 Home Premium 64bit i7-3770K box like 5 years ago. I think I used HyperSLI 0.95. It was working in SLI. Then something broke, and I left the box sit. Now... With the current and recent nVidia drivers I see both 460's in the Windows Device Mgr; I can select either or even the iGPU for PhysX. No SLI, though. I've tried a few versions of HyperSLI but I get BSOD after POST. I rolled back the UEFI BIOS a couple times; no change. So, please tell me what combo of drivers (and BIOS) will work. Or is there a registry hack? Or a driver hack? My plan is to locate the drivers known good back in 2013 or so. Then I'll try to update one at a time. Sounds like hours of tedium with very little gain. EVGA GTX460 2Win Intel i7-3770K Asus P8Z77-I Deluxe Intel Panther Point Z77, Intel Ivy Bridge AMI 2014-06-20 1201 Kernel/HAL 6.1.7601.2436 Win7sp1_ldr_escrow.180815-1700 nVidia drivers 9.18.13.697
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/11 14:29:27
(permalink)
Install driver 388.71 & then use DSLIA.
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/11 15:21:24
(permalink)
If driver 388.71 fails to work for you try using 387.92.
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/11 19:50:55
(permalink)
388.71 doesn't enable SLI but it claims patch succeeds. I will try 387.92 but first the README says > version 1.7 25/05/17 Supporting WHQL up to 382.33 so I'll d/l that one first.
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/11 20:06:41
(permalink)
That is for version 1.7. You're using 1.7.1 which should work just fine with 387.92.
|
MhzManiac
SSC Member
- Total Posts : 772
- Reward points : 0
- Joined: 2011/03/22 06:01:42
- Location: U.P., Washington
- Status: offline
- Ribbons : 8
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/11 21:48:11
(permalink)
Maybe a silly question, but the jumper connector is still in place on the video cards, right?
That is me in the picture, anyone else ever pet a live Lion?EVGA Z390 FTW (Bios 1.08) i9-9900KF 8 core, 32G Corsair Vengeance LPX Dual Chl 3000 XMP-1 , Intel SSD6 M.2 2TB, Samsung 840 PRO 1TB / 512G SSD, Gigabyte RTX 2080 Super , Win 11 Pro 64, EVGA Supernova 1300 watts, NZXT Phantom 820, Strix Raid DLX 7.1 surround, Corsair H100 Liquid , Dell S2417DG /S2409W / Acer XB241H Predator / Samsung C24F390 Curve/ Oculus Rift S VR
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 07:58:30
(permalink)
@MhzManiac The SLI jumper is internal I believe, the 2Win (twin) has 2 GPUs on one board. I haven't touched the hardware since my "known good" working condition in 2013. @Saijin Yes 1.7.1 "should" work, but I haven't succeeded yet. Could be user error. I also tried 1.6, same no-love. (And I notice 1.6 README only includes info up to 1.4--that is, 1.7.1 includes support more recent than 1.7) The patch works, or seems to. I get a driver that is signed, deployed, loaded on reboot. I do not get SLI. I've tried drivers 382.33, 388.71, 314.22
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 10:57:11
(permalink)
Looks like you're out of luck.
|
MhzManiac
SSC Member
- Total Posts : 772
- Reward points : 0
- Joined: 2011/03/22 06:01:42
- Location: U.P., Washington
- Status: offline
- Ribbons : 8
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 11:43:21
(permalink)
Try an external jumper board and see it it helps. I know win 10 looks for that connection.
That is me in the picture, anyone else ever pet a live Lion?EVGA Z390 FTW (Bios 1.08) i9-9900KF 8 core, 32G Corsair Vengeance LPX Dual Chl 3000 XMP-1 , Intel SSD6 M.2 2TB, Samsung 840 PRO 1TB / 512G SSD, Gigabyte RTX 2080 Super , Win 11 Pro 64, EVGA Supernova 1300 watts, NZXT Phantom 820, Strix Raid DLX 7.1 surround, Corsair H100 Liquid , Dell S2417DG /S2409W / Acer XB241H Predator / Samsung C24F390 Curve/ Oculus Rift S VR
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 11:57:51
(permalink)
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 12:15:43
(permalink)
If I remember correctly this is 2 chips on one PCB, so there'll be no connectors for a jumper.
I had it running in SLI 5 years ago. All the software is still out there. The question is ROI for time to find and fiddle.
Did I read somewhere the secret is to expose the switch/setting on the Nvidia Experience panel? The MOBO maker pays a SLI licence--which mine wouldn't on mITX with 1x16 and 2x4 PCIe.
Maybe I can have a chat with the fellow maintaining DSLIA. I'll keep ya posted!
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 12:27:00
(permalink)
bcavnaugh This card has single SLI Fork like the GTX 690 and runs Quad SLI unlike 4-Way SLI. BETA Win 7
Can you point me to more info re "single SLI fork"? I'll search on "Quad SLI unlike 4-Way SLI" also. Thanks. The timing on that beta driver looks right. Perhaps I used that together with HyperSLI 0.96 (that I just found hiding under the /Windows folder). BTW HyperSLI references "/Windows/Sysnative", a folder I don't see in Win 7--is that causing the BSOD? Can I point those refs to "/Windows/system32"?
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/12 12:43:32
(permalink)
mickleby
bcavnaugh This card has single SLI Fork like the GTX 690 and runs Quad SLI unlike 4-Way SLI. BETA Win 7
Can you point me to more info re "single SLI fork"? I'll search on "Quad SLI unlike 4-Way SLI" also. Thanks.
The timing on that beta driver looks right. Perhaps I used that together with HyperSLI 0.96 (that I just found hiding under the /Windows folder). BTW HyperSLI references "/Windows/Sysnative", a folder I don't see in Win 7--is that causing the BSOD? Can I point those refs to "/Windows/system32"?
Sysnative = System32. So yes.
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/13 12:55:07
(permalink)
Update: I've tried GeForce driver 326.80 beta, ditto DSLIA, ditto HyperSLI1.0, and ditto HperSLI0.96. With the vanilla driver and DSLIA'd just no difference -> PhysX all 3 GPU but no SLI settings. Both HyperSLI yield BSOD. The NTOSKrnl and HAL are both 2018-09, so maybe that's the issue with HyperSLI. I could roll back the BIOS. Also, I disabled Lucid but I know Lucid was running back when things worked.
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/13 12:56:53
(permalink)
Sounds like you're out of luck.
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/13 12:59:26
(permalink)
Did you even end up testing driver 387.92 like I suggested?
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/13 12:59:55
(permalink)
On my old Z77 MB If I enabled Lucid in the Bios and the Drivers if I tried to enable SLI on my GTX 680 Cards it would give me a BSOD. I could only run SLI with the Lucid Drivers uninstalled and then Disabled in the Bios.
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/13 15:07:04
(permalink)
@bcavnaugh I couldn't get Lucid to install, anyway. That led to a rabbit hole. I tried to use the iGPU. Couldn't get HDMI to provide signal. When I'm running thru the GTX I see the iGPU is available for PhysX. I completely removed the GPU, reset CMOS, bang bang, but no Intel i7 iGPU HDMI signal. @Sajin I thought I had tried 387.92 but I don't see its installer. I'm d/l now, will update you
|
MhzManiac
SSC Member
- Total Posts : 772
- Reward points : 0
- Joined: 2011/03/22 06:01:42
- Location: U.P., Washington
- Status: offline
- Ribbons : 8
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/13 22:57:16
(permalink)
If I remember correctly this is 2 chips on one PCB, so there'll be no connectors for a jumper. Not a MB jumper but GPU connector.
post edited by MhzManiac - 2018/10/13 23:04:06
Attached Image(s)
That is me in the picture, anyone else ever pet a live Lion?EVGA Z390 FTW (Bios 1.08) i9-9900KF 8 core, 32G Corsair Vengeance LPX Dual Chl 3000 XMP-1 , Intel SSD6 M.2 2TB, Samsung 840 PRO 1TB / 512G SSD, Gigabyte RTX 2080 Super , Win 11 Pro 64, EVGA Supernova 1300 watts, NZXT Phantom 820, Strix Raid DLX 7.1 surround, Corsair H100 Liquid , Dell S2417DG /S2409W / Acer XB241H Predator / Samsung C24F390 Curve/ Oculus Rift S VR
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 07:23:06
(permalink)
@MhzManiac I don't understand. This is one card, one dual-gpu card. @Sajin no love with the driver you suggest. So the old drivers (285.62, 296.10) also BSOD with HyperSLI (0.96, 1.0). I think the kernel/hal have changed too much for HyperSLI, or maybe I could still try with old BIOS. Plus they won't support my 2560x1080 monitor. I want to track down the issue of integrated GPU before I try to contact DSLIA peeps. I naively thought, just plug into HDMI on MOBO. Then I pulled GFX. Then I cleared CMOS. I THINK I remember a setting in the BIOS that is no longer there, to disable iGPU. Where did it go? Intel diagnostic tool skips gfx check when connected to gfx card. Hmm. I have an i3. I could swap CPUs to see if I get mobo video signal. So much work and risk of error. AND this mITX box is so inconvenient! Aside from one wasted GTX460 it is a fine machine. Maybe I will sleep on it for a week before I risk bending cpu pins on the mobo.
post edited by mickleby - 2018/10/14 07:25:44
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 07:46:53
(permalink)
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 10:43:45
(permalink)
@bcavnaugh "Maybe it is just time to upgrade your computer now." But I HAD it working! :D I'll track down SLI Patch 1.5. HyperSLI is the continuation, the replacement and extension of SLIPatch1.5. Same dev, anatolymik. It's funny you link PCPer because I'm in that forum reporting I got the SLI to work with HyperSLI on this SAME BOX. I do not mention the HyperSLI version or the drivers and obviously Windows (though still 7 SP1) has moved on regardless. Sure I have the install DVD and there are ISOs of intermediate versions.. But again, ROI. I have a thought about the HDMI mobo port. Maybe "way back then" the Intel drivers wouldn't stretch to 2560x1080 like the "ancient" nVidia 275.33 already did. I have another display to try. Way too many moving parts after 5 years. And THINK MORE THAN TWICE about using super small mItx cases!
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 10:49:30
(permalink)
Aside: There's something screwy with this Quick Reply editor. That last post, #22, is missing a hyperlink I added -- and the text under the link as well. Worse still, I made a post that would have been #19. Where is it? Was there a race condition with another poster? I'm using the latest Chrome Version 69.0.3497.100 (Official Build) (64-bit), fully updated Win 7 Home Premium SP1.
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 11:14:36
(permalink)
With some of the Windows 7 Patches lately it is hard to keep even our Older OS Computers running well anymore.
post edited by bcavnaugh - 2018/10/14 11:16:40
|
mickleby
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2012/09/16 13:02:23
- Status: offline
- Ribbons : 0
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 11:34:08
(permalink)
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 11:54:56
(permalink)
|
MhzManiac
SSC Member
- Total Posts : 772
- Reward points : 0
- Joined: 2011/03/22 06:01:42
- Location: U.P., Washington
- Status: offline
- Ribbons : 8
Re: GTX 460 2Win SLI non-SLI board PCIe 2.0 x16
2018/10/14 20:59:13
(permalink)
@MhzManiac I don't understand. This is one card, one dual-gpu card. Okay, now I understand. Never had a card like that so I will bow out. Hope you have success!
That is me in the picture, anyone else ever pet a live Lion?EVGA Z390 FTW (Bios 1.08) i9-9900KF 8 core, 32G Corsair Vengeance LPX Dual Chl 3000 XMP-1 , Intel SSD6 M.2 2TB, Samsung 840 PRO 1TB / 512G SSD, Gigabyte RTX 2080 Super , Win 11 Pro 64, EVGA Supernova 1300 watts, NZXT Phantom 820, Strix Raid DLX 7.1 surround, Corsair H100 Liquid , Dell S2417DG /S2409W / Acer XB241H Predator / Samsung C24F390 Curve/ Oculus Rift S VR
|