SPlacker
New Member
- Total Posts : 26
- Reward points : 0
- Joined: 2014/07/05 17:09:32
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/01/25 21:45:24
(permalink)
kring
Thanks Nereus - and to confirm, these latest bios for the hybrid have unlock fans that I can lower below 33% like the air cooled bios?
I can't speak for the 3090. However, I recently installed the hybrid kit on my RTX 3080 FTW3 Ultra (Low Hashrate). I disabled fast boot (CSM was already disabled, on MSI boards this means having it set to UEFI only mode) and flashed the VBIOS in the screenshot below. Rebooted, ran X1, it said there was a firmware update for my card, I hit ok and the radiator fans and fan on the shroud instantly went to 100 percent and the 3 power LED's turned red but I'm fairly sure that's normal during a firmware update. The update applied successfully. I rebooted and ran X1 again to make sure the update installed successfully. X1 didn't say my firmware needed an update so it must have. I then shut down my PC, put the BIOS switch in the OC position and flashed the OC mode VBIOS included in the download and that worked fine as well. I rebooted ran X1 again while the card was in OC mode to make sure it didn't need to update the card with the VBIOS switch in the OC position. It didn't. Shutdown, put the switch back to regular mode and that was it.  The fan on the shroud never fully stops, it goes as low as 30% fan speed, but even with afterburner I can't force a zero RPM mode. IDK if this is regular behavior for the Hybrid or not. But it's fine with me since at that speed (~800 RPM) it's not audible at all. The radiator fans do fully stop when the GPU is below a certain temp. I'm assuming 60c like the other cards, but I actually can't get my GPU temp to get higher than ~55-56c no matter what I try. I've tried multiple games, multiple burn in tools etc but I've never gotten my GPU temp above ~56c since installing the hybrid cooler. But I'm assuming that is when the radiator fans would start spinning and ramp from there. Again, IDK if this is normal behavior for the hybrid or not. I can control the fan on the shroud and the radiator fans just fine with Afterburner, other than not being able to set the shroud fan below 30 percent. I may re-install X1 for a bit just to see if it can, but I'd be surprised if it were any different and like I said I don't mind since it's such a low speed. I've had no issues so far. No weird fan behavior like random fan speed spikes which I've seen posts about from people that installed the hybrid cooler and flashed their card to the hybrid VBIOS.
post edited by SPlacker - 2022/01/25 21:49:18
Intel Core i7 8700K @ 4.5 Ghz all core DEEPCOOL Assassin III CPU Cooler 3080 FTW3Ultra (Hybrid cooler kit installed) 32 GB DDR4 3200 RAM (4 x 8GB) 1 TB WD Black SN 750 PCI-E 3.0 NVME 1 TB HP EX 920 PCI-E 3.0 NVME 2x 3 TB Seagate 7200 RPM HDD in RAID0 MSI Z370 SLI Plus SuperFlower Leadex V Gold Pro 850W be quiet! Pure Base 500DX Black Case
|
ra773
New Member
- Total Posts : 19
- Reward points : 0
- Joined: 2017/04/10 14:30:44
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/01/26 03:30:05
(permalink)
MDN79
Hi, guys!
What about some issues on 3080 ti FTW3 U? I visited the topic long ago.
Maybe solution for unequal power distribution between cords attached was finally discussed?
3rd cord draws at least twice less power compared to 1st and 2nd. Sure you all know that.
Also maybe there were lucky boys who can reach 450 Wt on ti FTW3U?
I'm so rage when the card shoes me reaching power limit in simple Heaven benchmark at 400 Wt with setting of 118%.
Also I'm wondering if card keeps power limit setting in ROM or whenever. Because I saw strange thing. Some day I launched Kombustor and saw just 400 Wt and limiting. But Afterburner told me about 118% set. I could only increase wattage limit with X1. So the qeustion is if X1 force the card to keep this limit inside despite of other program try to set (I mean MS AB of course)?
Also, EVGA, please, issue XOC bois with more limit for Ti FTW3U, at least 480 Wt.
That's really unfair that simple 3080 has 450 and much more powerfull Ti has the same.
I don't want to use HOF 1000 Wt bois as it hurt monitoring of voltages and can lead to strange power draw from cords, which might be dangerous for card.
i fully support this request. give us a BIOS thats able to use 450 at least. my old 3080 ftw3 could be run right at 450 watt / this 3080ti ftw3 cant even get their. you could surely give us 3080ti ftw3 owner some love with a 480 watt bio and a balanced pci-e 3 plug. their is no reason to buy a 3080ti ftw3 otherwise. any other 3080ti can do allmost the same powerlimits the 3080ti ftw3 can do right now.
|
xboxhaxorz
New Member
- Total Posts : 5
- Reward points : 0
- Joined: 2022/01/31 23:30:11
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/01/31 23:33:09
(permalink)
I ordered the 3080 12GB Hydro Copper and the 240mm Hybrid kit, which is the appropriate bios for me?
|
marvin5885
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2021/03/19 10:27:49
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/05 18:08:57
(permalink)
A friend is willing to sell me his RTX 3080 TI Ultra Hybrid since he upgraded to a 3090 Kingpin, I would like to mine on it on the side to make some extra money and I heard there was a BIOS release for the 3080 Ti FTW3 air cooled card that unlocked mining performance. Would I be able to flash my hybrid card with this air cooled BIOS in order to unlock the performance?
|
hurikata
New Member
- Total Posts : 2
- Reward points : 0
- Joined: 2022/02/07 03:45:10
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/07 04:03:43
(permalink)
Hi
I did install the RTX 3080 FTW3 HYBRID LHR XOC BIOS on my graphics card( EVGA RTX 3080 FTW3 ultra hybrid 10G)
Both bios (normal and OC)
The Normal bios stay 400W and the OC bios change to 450W.
Unfortunatelly with the OC bios I have same 400W limit, if the powerconsumption above 400W comes throttling.
With new bios my card not so stable like before.I can stabilize my card at 30MHz less boostfrequency.
Before XOC bios installation I did save my original bios files with gpu-z
I installed back both original bioses(normal and OC) with nvflash
I have now same issue as like as with XOC bios. I can stabilize my card at lower boostfrequency.
I did download the normal rebar bios files from this website, after insallation same issue.
I changed nothing on my pc.
Same driver, same settings in motherboard bios
What can I do? Any solutions?
Y.S.
HK
|
sgtcoder
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2022/02/08 15:09:09
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/09 13:01:46
(permalink)
Thank you for these BIOS. I have a couple questions though: - What's the point of flashing the OC BIOS if we can flip the switch to OC on the EVGA card? Wouldn't it just use the OC BIOS and it would update using Precsion X1? Or is the update only to increase to 450W limit?
- If we applied the BIOS update provided here, wouldn't X1 Precision update and overwrite the Custom BIOS?
post edited by sgtcoder - 2022/02/09 13:55:14
|
icephreaq
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2018/08/22 04:55:03
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/19 17:54:02
(permalink)
This thread is greatly appreciated. Just installed a Hybrid kit on my 3080 XC3 Ultra and flashed it to the Hybrid verion without any issues. 
|
h2olgd
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2015/03/20 14:22:08
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/22 05:27:13
(permalink)
So, it looks like I may have gone backwards. After flashing to the Hybrid 3090 OC BIOS (went H2O) my max power is capped at 350w and boost freq's are a bit lower. I went back to the regular OC BIOS (from this thread) and I'm still capped at 350w. I've seen in the past where EVGA could help out if they have the current ROM. The deviceID reads correct, so hopefully it's an obvious find. Well, here's the current ROM: (ok, my link was removed. How to link to file?) Thank you for any help/advice.
post edited by h2olgd - 2022/02/22 05:34:26
|
SPlacker
New Member
- Total Posts : 26
- Reward points : 0
- Joined: 2014/07/05 17:09:32
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/23 13:40:40
(permalink)
So as I said in my post on the previous page, I successfully flashed my RTX 3080 FTW3 Ultra LHR to the "EVGA GeForce RTX 3080 FTW3 HYBRID LHR (10G-P5-3898-KL) [ReBAR]" VBIOS. Ran Precision X1, which updated the firmware, rebooted again and my card shows up as a Hybrid card now.
I wanted to try the XOC 3080 LHR FTW3 Hybrid VBIOS, but when I try to flash the XOC VBIOS it says my VBIOS is up to date and won't flash the XOC version.
Intel Core i7 8700K @ 4.5 Ghz all core DEEPCOOL Assassin III CPU Cooler 3080 FTW3Ultra (Hybrid cooler kit installed) 32 GB DDR4 3200 RAM (4 x 8GB) 1 TB WD Black SN 750 PCI-E 3.0 NVME 1 TB HP EX 920 PCI-E 3.0 NVME 2x 3 TB Seagate 7200 RPM HDD in RAID0 MSI Z370 SLI Plus SuperFlower Leadex V Gold Pro 850W be quiet! Pure Base 500DX Black Case
|
jonathan2486
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2022/01/31 17:11:42
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/24 10:21:11
(permalink)
I just installed a hybrid kit on a 12GB 3080 HC — 12G-P5-4879-KL. Any bios flash for this?
post edited by jonathan2486 - 2022/02/24 10:22:41
|
bjdanikowski
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2018/03/09 11:39:27
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/02/26 15:37:52
(permalink)
after downloading the bios file for my 3080 FTW3 Ultra LHR and unzipping them, when I double click or try to run either of the files nothing happens.... I don't get any windows poping up to then click "y"
|
hurikata
New Member
- Total Posts : 2
- Reward points : 0
- Joined: 2022/02/07 03:45:10
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/03 08:51:51
(permalink)
So again. Pls help. I can not flash the XOC BIOS at normal bios mode, only at OC bios mode I do everything how it is in the description. I did reset my motherboard bios. set to UEFI mode Fastboot disabled. I allready tried to flash in normal and safe mode too in windows 10. and the nvflash show me this: ...the firmware is up to date and still 400W original "NORMAL" bios. I tried to flash to XOC OC bios to switch to normal bios mode, and same.... the firmware is up to date and just 400W... Before all I did save the both original bioses. If I flash back original both bioses (normal and OC) and try to flash first the normal bios, same...the firmware is up to date and just 400W... If anybody flashed both bioses,and both are 450W can me please save both bios files(.DA,.DB) with gpu-z and upload somewhere and send me a link? Y.S. P.S.: I get tdp limit at 400W vith the XOC OC bios, but normally the limit is at 450W I want to try my card what happens if i flash both bioses. I dont know why but I can not send the links from pictures.
post edited by hurikata - 2022/03/03 08:56:04
|
Shaun6479
New Member
- Total Posts : 3
- Reward points : 0
- Joined: 2021/07/15 05:17:24
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/10 20:31:47
(permalink)
hi guys quick question recently did the hybrid conversion on my 3080 ftw3 ultra Lhr card and im looking for the bios to flash it to make it act like the hybrid version but ive looked at the bios listed and it says be sure that my numbers match well the numbers that are listed for the bios is 3898,,,, mine is 3897 -kl can i use the 3898 bios or is there a seperate one for this number. thanks in advance.
|
SPlacker
New Member
- Total Posts : 26
- Reward points : 0
- Joined: 2014/07/05 17:09:32
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/11 19:12:14
(permalink)
hurikata
So again.
Pls help.
I can not flash the XOC BIOS at normal bios mode, only at OC bios mode
I do everything how it is in the description.
I did reset my motherboard bios.
set to UEFI mode
Fastboot disabled.
I allready tried to flash in normal and safe mode too in windows 10.
and the nvflash show me this: ...the firmware is up to date and still 400W original "NORMAL" bios.
I tried to flash to XOC OC bios to switch to normal bios mode, and same.... the firmware is up to date and just 400W...
Before all I did save the both original bioses.
If I flash back original both bioses (normal and OC) and try to flash first the normal bios, same...the firmware is up to date and just 400W...
If anybody flashed both bioses,and both are 450W can me please save both bios files(.DA,.DB) with gpu-z and upload somewhere and send me a link?
Y.S.
P.S.: I get tdp limit at 400W vith the XOC OC bios, but normally the limit is at 450W
I want to try my card what happens if i flash both bioses.
I dont know why but I can not send the links from pictures.
I sent a PM to the EVGA member that made this thread about this exact issue. This was his reply. " I don't think I have the XOC versions for the LHR HY cards yet, so that's going to be the issue, currently. I'll check again with our team." Hopefully it gets sorted but who knows.
Intel Core i7 8700K @ 4.5 Ghz all core DEEPCOOL Assassin III CPU Cooler 3080 FTW3Ultra (Hybrid cooler kit installed) 32 GB DDR4 3200 RAM (4 x 8GB) 1 TB WD Black SN 750 PCI-E 3.0 NVME 1 TB HP EX 920 PCI-E 3.0 NVME 2x 3 TB Seagate 7200 RPM HDD in RAID0 MSI Z370 SLI Plus SuperFlower Leadex V Gold Pro 850W be quiet! Pure Base 500DX Black Case
|
SPlacker
New Member
- Total Posts : 26
- Reward points : 0
- Joined: 2014/07/05 17:09:32
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/11 19:16:30
(permalink)
Shaun6479
hi guys quick question recently did the hybrid conversion on my 3080 ftw3 ultra Lhr card and im looking for the bios to flash it to make it act like the hybrid version but ive looked at the bios listed and it says be sure that my numbers match well the numbers that are listed for the bios is 3898,,,, mine is 3897 -kl can i use the 3898 bios or is there a seperate one for this number. thanks in advance.
I installed the hybrid kit on my LHR 3080 FTW3 Ultra. I used this download https://www.evga.com/EVGA/GeneralDownloading.aspx?file=4898.zip Just make sure you follow the other directions (turning off fast boot in your BIOS, and CSM which in MSI's case means just having the mobo set to UEFI only). Do a few reboots, flash the regular VBIOS (the one for the card in the non OC BIOS position). Reboot, maybe twice for good measure. Launch Precision X1 and it will update the cards firmware (RGB lighting, fan control etc). Then repeat for the card in the OC position with the OC VBIOS. I did that and it's working perfectly.
Intel Core i7 8700K @ 4.5 Ghz all core DEEPCOOL Assassin III CPU Cooler 3080 FTW3Ultra (Hybrid cooler kit installed) 32 GB DDR4 3200 RAM (4 x 8GB) 1 TB WD Black SN 750 PCI-E 3.0 NVME 1 TB HP EX 920 PCI-E 3.0 NVME 2x 3 TB Seagate 7200 RPM HDD in RAID0 MSI Z370 SLI Plus SuperFlower Leadex V Gold Pro 850W be quiet! Pure Base 500DX Black Case
|
dmoheban
SSC Member
- Total Posts : 910
- Reward points : 0
- Joined: 2003/07/08 15:35:10
- Status: offline
- Ribbons : 3
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/12 06:52:01
(permalink)
Hi guys,
Just installed a new 3080 Ti FTW3 card and installed Precision which said bios needed to be updated and updated it to the latest bios for the card.
Was wondering out of curiosity what changes were made?
Thanks
Associate Code: K8XL098LGS5O4WZ
|
SPlacker
New Member
- Total Posts : 26
- Reward points : 0
- Joined: 2014/07/05 17:09:32
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/17 01:06:17
(permalink)
I don't think EVGA puts out update notes for new VBIOS or firmware versions
Intel Core i7 8700K @ 4.5 Ghz all core DEEPCOOL Assassin III CPU Cooler 3080 FTW3Ultra (Hybrid cooler kit installed) 32 GB DDR4 3200 RAM (4 x 8GB) 1 TB WD Black SN 750 PCI-E 3.0 NVME 1 TB HP EX 920 PCI-E 3.0 NVME 2x 3 TB Seagate 7200 RPM HDD in RAID0 MSI Z370 SLI Plus SuperFlower Leadex V Gold Pro 850W be quiet! Pure Base 500DX Black Case
|
Audioboxer
Superclocked Member
- Total Posts : 190
- Reward points : 0
- Joined: 2020/10/25 14:14:53
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/20 11:53:40
(permalink)
Is there any particular reason people flash the Hybrid versions of a BIOS? The 450w BIOS exists for my FTW3 Gaming Ultra but I went ahead and flashed the Hybrid BIOS just to see if it works, and well, yeah, of course it does lol  I am watercooling my card so I technically have a Hybrid lol, but again is the Hybrid bios adding anything when the FTW Gaming Ultra already has a 450w version? Or is this just supposed to be for people who buy a Hybrid kit and want to convert? I guess it does no harm for me to be running this seeing as I have no fans connected anyway 
post edited by Audioboxer - 2022/03/20 11:55:46
|
Draslay31
New Member
- Total Posts : 49
- Reward points : 0
- Joined: 2017/08/28 11:57:48
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/24 04:40:52
(permalink)
Good morning everyone, Since the 3090 FTW3 Ultra has been available on the EVGA website several times this week - I purchased one. I was originally waiting for the Kingpin yet have given up unfortunately. Some questions: - has the "new" version of the 3090 FTW3 Ultra (24G-P5-3987-KR) been redesigned and the XOC bios and power draw issue(s) resolved? -- Has the soldering defect been resolved/Load line balancing? - What is the "BEST" Bios for the 3090 FTW3 Ultra for someone that likes OC'ing and runs the OC 24/7? I do not mind fan noise AT ALL :) -- Is one software tool better than the other for the 3090 series cards? Precision X VS MSI Afterburner? I usually use MSI Afterburner yet am familiar with PX Thank you everyone in advance for helping out and please forgive my ignorance around my questions - hence me asking :)
post edited by Draslay31 - 2022/03/24 04:59:50
|
Bluedog1991
New Member
- Total Posts : 12
- Reward points : 0
- Joined: 2020/11/26 07:52:41
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/27 01:40:25
(permalink)
After rma’ing the launch series of the ftw 3 3090 ultra oc (clown lips) I am Still waiting on a bios for 3090 ftw 3 ultra oc that will actually let me get close to 500w. We all know that even though it says we have the xoc 500w bios, we still can’t get close to it…. However I will give them the benefit of the doubt by saying that at least they fixed the load balance. But after paying $2000 for a gpu, I want to at least come close to 500w. Especially after spending close to another $1000 on a watercool setup just so I can oc the crap out of the card but can’t even come close to 500w….
|
d333s
New Member
- Total Posts : 31
- Reward points : 0
- Joined: 2004/08/11 13:48:28
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/27 03:57:12
(permalink)
While I prefer the Nvidia reference designed cards, for my latest PC upgrade I purchased a rather disappointing 12G-P5-3955-KR video card. In trying to increase its performance to "average", I've run into the limit of the Power Target setting of 105%.
In response to a question about Precision X1's ability to configure slightly high settings, I was told it's a firmware limitation. It would require a "higher power limit " BIOS.
Looking on the download page and video cards forum, the only BIOS appears to address the limit is the: "EVGA GeForce 30 Series HYBRID/XOC/Default BIOS" thread. (Although, most posts in the thread reference the FTX and Hybrid cards.)
Is this the only "officially" released BIOS that can permit increasing the Power Target?
Intel Core i7-12700KF Desktop Processor 12 (8P+4E) Cores up to 5.0 GHz Unlocked ASUS ROG Strix Z690-E Gaming WiFi 6E LGA 1700(Intel 12th Gen)ATX gaming motherboard CORSAIR Vengeance DDR5 32GB (2x16GB) DDR5 5600 (PC5-44800) C36 1.25V - Black EVGA GeForce RTX 3080 Ti XC3 ULTRA GAMING, 12G-P5-3955-KR, 12GB GDDR6X, iCX3 Cooling 2 x Samsung - 980 PRO 1TB PCIe Gen 4 x4 NVMe Gaming Internal Solid State Drive AX1200i Digital ATX Power Supply — 1200 Watt 80 PLUS® Platinum Certified Fully-Modular PSU 2 x PNY XLR8 CS3040 4TB M.2 NVMe Gen4 x4 Internal Solid State Drive (SSD) - M280CS3040-4TB-RB 2 x SAMSUNG 870 QVO SATA III 2.5" SSD 1TB (MZ-77Q1T0B) 1 x WD RE 4 TB Enterprise Hard Drive: 3.5 Inch, 7200 RPM, SATA III, 64 MB Cache - WD4000FYYZ
|
TiltedBox
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 2022/03/28 16:55:09
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/29 07:26:21
(permalink)
EVGATech_LeeM
vcast
@EVGATech_LeeM
Thank you for the info. I ran the BIOS for the 3080 FTW3 HYBRID, and I am now seeing that I have an ULTRA Hybrid in X1. Is this common for the FTW3 to show as an ULTRA after running the bios update?
I have been troubleshooting an issue where my aio radiator fans with the hybrid rev up on their own when I am in a game. Regardless of fan control settings in X1, or if I close it and try to use Afterburner, my fans will rev to 100%.
Technically, all the HYBRID cards in the 30 Series are considered "ULTRA", since they all are factory overclocked out of the box. Leaving aside that you can probably find some confusion on our marketing/naming on the products which don't necessarily say "ULTRA", there is only one version of each HYBRID card.
Regarding the fan issues, I'll send you a PM.
@ EVGATech_LeeM
I have the same fan issues. Could you help me if you found a fix for it?
post edited by TiltedBox - 2022/03/29 08:34:59
|
Talon2020
iCX Member
- Total Posts : 316
- Reward points : 0
- Joined: 2016/05/26 12:17:13
- Status: offline
- Ribbons : 3
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/03/30 10:38:05
(permalink)
Just out of curiosity, why does the RTX 3090 FTW3 card have a 500w vBIOS but the higher end 3090 Ti FTW3 have a 480w vBIOS? Is the XOC vBIOS for the 3090 Ti FTW3 coming? I would expect at a minimum 500w to match what crappy Zotac is offering for their cards or 515w that Asus is offering on their cards.
i9 13900K | EVGA Z690 DARK | NVIDIA RTX 4090 FE | 32gb DDR5 8000 CL36 SK Hynix A-Die | Samsung 980 Pro 2TB | EVGA 1000 P6 | LG C1 55 OLED 4K 120Hz G-Sync
|
aostang
New Member
- Total Posts : 34
- Reward points : 0
- Joined: 2017/06/11 21:32:35
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/01 13:14:45
(permalink)
Talon2020
Just out of curiosity, why does the RTX 3090 FTW3 card have a 500w vBIOS but the higher end 3090 Ti FTW3 have a 480w vBIOS? Is the XOC vBIOS for the 3090 Ti FTW3 coming? I would expect at a minimum 500w to match what crappy Zotac is offering for their cards or 515w that Asus is offering on their cards.
Agreed. Maybe they want to make sure everything is stable on the first cards out to the public before offering it. If they don't, I'm sure someone will bake one up and I think it would be in EVGA's interest to offer an official one so a ton of people aren't flashing some other random BIOS they found somewhere.
|
BattlePhenom
New Member
- Total Posts : 6
- Reward points : 0
- Joined: 2012/07/06 03:50:37
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/03 10:43:07
(permalink)
Better yet, how about 525w as the pci-e lane(75w) and 16 pin(450w) should be able to handle that.
|
madreag
New Member
- Total Posts : 16
- Reward points : 0
- Joined: 2010/08/19 23:44:26
- Status: offline
- Ribbons : 0
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/03 10:55:43
(permalink)
BattlePhenom
Better yet, how about 525w as the pci-e lane(75w) and 16 pin(450w) should be able to handle that.
I agree! ASUS currently has a 516W limit on their 3090 ti, so EVGA should at least be able to match this on their XOC bios. This card runs extremely cool for the amount of power running through it. It will handle 500W+ on the default cooler. I mention this because one could argue that the OG EVGA 3090 FTW3's cooling was borderline for that much power. EVGA have vastly improved their default coolers going from 3090 FTW3 to 3090 ti FTW3.
post edited by madreag - 2022/04/03 10:57:05
|
Talon2020
iCX Member
- Total Posts : 316
- Reward points : 0
- Joined: 2016/05/26 12:17:13
- Status: offline
- Ribbons : 3
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/03 11:37:50
(permalink)
Well right now EVGA hasn't even responded. I made a post about the power limits being lower then the old 3090 and it went unanswered. I'm hoping they are just tuning the XOC or higher PWL version for release soon.
i9 13900K | EVGA Z690 DARK | NVIDIA RTX 4090 FE | 32gb DDR5 8000 CL36 SK Hynix A-Die | Samsung 980 Pro 2TB | EVGA 1000 P6 | LG C1 55 OLED 4K 120Hz G-Sync
|
AHowes
CLASSIFIED ULTRA Member
- Total Posts : 6502
- Reward points : 0
- Joined: 2005/09/20 15:38:10
- Location: Macomb MI
- Status: offline
- Ribbons : 27
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/07 12:47:27
(permalink)
So i have a recent 3090 FTW3 Ultra card.. Is their any reason to flash to a Hybrid Bios if i'm now using a EK front and back block?? Does it give a higher power limit or is it just a Name change in PX1?
Intel i9 9900K @ 5.2Ghz Single HUGE Custom Water Loop. Asus Z390 ROG Extreme XI MB G.Skill Trident Z 32GB (4x8GB) 4266MHz DDR4 EVGA 2080ti K|NGP|N w/ Hydro Copper block. 34" Dell Alienware AW3418DW 1440 Ultra Wide GSync Monitor Thermaltake Core P7 Modded w/ 2x EK Dual D5 pump top,2 x EK XE 480 2X 360 rads.1 Corsair 520 Rad.
|
Jomama22
iCX Member
- Total Posts : 257
- Reward points : 0
- Joined: 2020/09/23 08:06:30
- Status: offline
- Ribbons : 19
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/07 13:04:55
(permalink)
AHowes
So i have a recent 3090 FTW3 Ultra card.. Is their any reason to flash to a Hybrid Bios if i'm now using a EK front and back block?? Does it give a higher power limit or is it just a Name change in PX1?
There shouldn't be any difference between the bios' interms of performance. I would shy away from using the hybrid bios as more than likely, the fans may not operate correctly (different rpm range/count).
|
AHowes
CLASSIFIED ULTRA Member
- Total Posts : 6502
- Reward points : 0
- Joined: 2005/09/20 15:38:10
- Location: Macomb MI
- Status: offline
- Ribbons : 27
Re: EVGA GeForce 30 Series HYBRID/XOC/Default BIOS Thread
2022/04/07 14:43:51
(permalink)
Jomama22
AHowes
So i have a recent 3090 FTW3 Ultra card.. Is their any reason to flash to a Hybrid Bios if i'm now using a EK front and back block?? Does it give a higher power limit or is it just a Name change in PX1?
There shouldn't be any difference between the bios' interms of performance. I would shy away from using the hybrid bios as more than likely, the fans may not operate correctly (different rpm range/count).
Yeah i'm not too worried about fans as i dont have any ;).. if theirs no difference then why bother.
Intel i9 9900K @ 5.2Ghz Single HUGE Custom Water Loop. Asus Z390 ROG Extreme XI MB G.Skill Trident Z 32GB (4x8GB) 4266MHz DDR4 EVGA 2080ti K|NGP|N w/ Hydro Copper block. 34" Dell Alienware AW3418DW 1440 Ultra Wide GSync Monitor Thermaltake Core P7 Modded w/ 2x EK Dual D5 pump top,2 x EK XE 480 2X 360 rads.1 Corsair 520 Rad.
|