kraade

Nice looking rig, kraade

Oh , I might add, the air cooler did a fantastic job, but it started out a run at 2040mhz but soon would saturate about 65-67c and by the end would be running 2010-1995mhz . This block is able to maintain the 2040, "stock " boost throughout a full 20 loop 4k pass.
This is a "gaming tier" card (83) and had 2040 wrote on the side if the GPU just like Steve's sample.

talon951

kraade
Its IN ,  did not have the patience to put in the third rad, so I am on the same system as the KPE HC, first PR run it was about 6 C cooler than the HC flat footed stock (418w KPE , 438w 90 TI ) AND<< left off the RGB cable , not a header or cable I could reach without tearing it down
Time Spy Ex stress test 20 pass
Clock 2040  - Average clock maintained was 2039
GPU temp 50.1 average
Hot spot 61 highest reading
mem junction 50
Perf cap VRel
mem1 42
mem2 41
mem3 41
pwr 1 41
pwr2 41
pwr3 42
pwr3 41 
pwr4 43
pwr4 41
1 360 SE  and 1 360 PE radiators , fans 60 %  , D5 @60% , 
just did a boosted PR run 15508 - +155clk +701mem , clock was a steady 2190 (which is where my old KPE would crash without massive messaging of the classy tool) , average temp 45 in run , 23.5 ambient and the thing cools off when at idle much faster. 
 
SO,  there you have it, any questions?
 

No water temp sensor?  What was the ambient temp?  How much does your gpu core temp change when you go to 100% pump?  
 
Based on the 50C max and 2x360, I'd say that is a good result though.  Mount is good given your hot spot delta is ~11C.  That's about the best I've done with either of my blocks.  The only criticism I'd have with your loop is that you have a lot of 90° fittings that hurt flow quite a bit.  

I did not know that , thanks. I did not add the third 360 because it would have been a full tear down, and I didn't have the time to do that right. This is the Dynamic not the xl and had to do some Dremel work to get this far.

newls1
awesome results sir!  Happy for you.  Cant wait for mine to ship any year now.......

May your wait be shorter than you hope,

kraade
It is assembled 

 
How difficult was it to remove the stock cooler?  I'm assuming it's easier than the 3090 since the 3090 ti stock cooler uses thermal pads instead of that thick putty.
 

talon951

kraade
Its IN ,  did not have the patience to put in the third rad, so I am on the same system as the KPE HC, first PR run it was about 6 C cooler than the HC flat footed stock (418w KPE , 438w 90 TI ) AND<< left off the RGB cable , not a header or cable I could reach without tearing it down
Time Spy Ex stress test 20 pass
Clock 2040  - Average clock maintained was 2039
GPU temp 50.1 average
Hot spot 61 highest reading
mem junction 50
Perf cap VRel
mem1 42
mem2 41
mem3 41
pwr 1 41
pwr2 41
pwr3 42
pwr3 41 
pwr4 43
pwr4 41
1 360 SE  and 1 360 PE radiators , fans 60 %  , D5 @60% , 
just did a boosted PR run 15508 - +155clk +701mem , clock was a steady 2190 (which is where my old KPE would crash without massive messaging of the classy tool) , average temp 45 in run , 23.5 ambient and the thing cools off when at idle much faster. 
 
SO,  there you have it, any questions?
 

No water temp sensor?  What was the ambient temp?  How much does your gpu core temp change when you go to 100% pump?  
 
Based on the 50C max and 2x360, I'd say that is a good result though.  Mount is good given your hot spot delta is ~11C.  That's about the best I've done with either of my blocks.  The only criticism I'd have with your loop is that you have a lot of 90° fittings that hurt flow quite a bit.  

Running a new TSE stress test , Ambient is 75F , put the pump at 100% @ 35C or better, results soon

kraade
Clock 2040  - Average clock maintained was 2012 97.8 % stable
GPU temp 48 average
Hot spot 60.1 highest reading
mem junction 49
Perf cap VRel
mem1 41
mem2 40
mem3 40
pwr 1 41
pwr2 41
pwr3 41
pwr3 41
pwr4 43
pwr5 40
so 100% pump from 60 % pump can be seen but is it worth it for a daily driver?
Benching, it can get you to the next tier but wear and tear on your components ?
card TPD was about 10 w lower too, not sure why

Probably isn't worth it to run 100% pump unless you just want the lowest possible temps. Looks solid though. Based on your power level and rad area, I'd guess your block delta is pretty good. Probably as good as my Alphacool block.

Good to see EK getting back to being more competitive possibly. They are usually one of the first with blocks so it's quite possible I'll end up with one for my 4090.

Kraade,
Thanks for sharing info on the Ti with the EK block.  It looks great and the performance numbers are pretty strong.  Getting three rads in the Dynamic case is not easy, but your's look clean.  
 
Using a medium thickness rad and a slim to cool your loop gives you room to grow cooling potential when you can add an additional 45mm rad to the side location and route the tubing.  The temps do look good though.  Not sure you will really need it though based on your temp numbers.  Would be interesting to see what your coolant temps are, but the bottom line is your component temps are good. 
 
Enjoy your build and thank for sharing.  

Kraade,
In the side mount location, you can fit up to a I believe a 47mm rad.  The EK Coolstream Classic PE (45mm) or their new Quantum P360M should fit in that location.  I haven't bought the Quantum rad yet, but for sure the Coolstream Classic will fit.  I've used the Coolstream classic there in my O11 builds with now issues.  It's a tight fit, but it will go there.  You will need to be sure to route the cables for the front panel effectively around the rad but I have done it on both the XL and the Dynamic.  
 
The dimensions for the new Quantum rad as far as thickness would fit, but the only thing I haven't looked at is the port spacing and making sure those clear the mounting tabs in the case.  The ports look to be recessed but I haven't had one in my hands yet.  I believe the rad comes with adapters to be used for the input/output ports. I haven't bought one yet but I've been thinking about it.  The problem for me as I already bought the rads I would need for my personal needs even when I move to my new 1000D Obsidian case.  I already have a matching 480mm rad to the one I have in my Phantecs build right now and I went out and got the 360mm rads I need if I decide to stick with the either of the following setups which would be twin Coolstream Classic 360mm rads, or Coolstream classic and one 360mm long Alphacool 44mm thick crossflow rad, or two 360mm long 54mm thick hardware labs rads.  
 
 

Kraade,
I missed that one about the disto plate.  

That is going to be a tight squeeze fitting the S model of the rad in there with the fans on the back side.  I was looking at those new EK rads and was  kicking myself a bit after they came out but I had already bought more rads than I need and while I am tempted to go all EK on the rads I can't see myself going through with it knowing I already have 500 plus in rads that would be sitting around if I did.  
 
Great build and glad it's working well for you.  The numbers you shared gives me confidence when the 4000 series comes out that I will go with the EK option when the time comes.  

Nereus, did you install your block yet?

I would say off hand it's longer than the air cooler because the 12pin pigtail goes inside that piece of acetal on the end of the card. The exact dementions of both are in the description and spec sheets available on the web pages of each piece.

RichK

kraade
I would say off hand it's longer than the air cooler because the 12pin pigtail goes inside that piece of acetal on the end of the card. The exact dementions of both are in the description and spec sheets available on the web pages of each piece.

Thanks, I was afraid of that. The amount of hot air this beast pumps into my case is crazy. Now I need to figure out a new spot for the second D5 so the card with the block installed will actually fit.

Yes I feel you, I decided to build in the Dynamic O11 , should have got an XL but I thought it was too big at the time. Now I am finding creative ways around it. That air cooler does great at dissipating heat but it has to go somewhere, when I was on air I left the glass pannel off.

Is it dual D5s on the distribution plate?

kraade
Nereus, did you install your block yet?

Unfortunately not - have been stupidly busy for months. Finally just finished my Mrs' build, which was months behind schedule lol, so maybe the next little block of time I have I can work on my own rig rebuild.