lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Hey. I have a question whether hwinfo can bugged read temperature and voltage?  this tempeatures buuged always and this normal or what is tath  like that now 10 min in anthem
post edited by lmatyja - 2019/04/02 10:47:34
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: dark x299 and seensors
2019/04/02 11:51:11
(permalink)
Software readings can be inaccurate. For voltages it's best to use a multimeter to get an accurate reading.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/04/02 11:56:10
(permalink)
but my friend have same settings and working good :(
and oki
uncore offset 1.25V its oki in bios is 295
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: dark x299 and seensors
2019/04/02 12:00:53
(permalink)
Your temps show the system at idle & load which is normal.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/04/02 12:02:50
(permalink)
normal is 1.15V uncore offset in bios and hw info buuged to 1.23V
same tmeps for 63
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/04/02 12:37:57
(permalink)
and i want 4000 mhz memory uncore offset its ok to 24/7 1.245V?
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: dark x299 and seensors
2019/04/02 14:56:49
(permalink)
lmatyja
its ok to 24/7 1.245V?
Yeah.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/04/02 21:58:54
(permalink)
|
Sajin
EVGA Forum Moderator
- Total Posts : 49168
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: online
- Ribbons : 199
Re: dark x299 and seensors
2019/04/02 22:42:06
(permalink)
Haha. No problem. 
|
TiN_EE
Yes, that TiN
- Total Posts : 377
- Reward points : 0
- Joined: 2010/01/22 21:30:49
- Location: xDevs.com
- Status: offline
- Ribbons : 14
Re: dark x299 and seensors
2019/04/10 00:22:37
(permalink)
Stuff like you seeing could be caused by other software interfacing motherboard SMBus controller. Perhaps you have some other software that runs in background, and causing interface collisions and error packets, resulting in wrong values in HWiNFO. Typical example of such software is RGB software for DIMMs or fan control software. Try to close everything except HWiNFO to see if issue persists.
If you have question, please post in public forum. I do not reply PMs, so all in community can benefit the answer.
|
bcavnaugh
The Crunchinator
- Total Posts : 38977
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: dark x299 and seensors
2019/04/10 12:22:20
(permalink)
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/05/06 01:00:35
(permalink)
oki tell me thane witch sensore give true DIMM voltage  ???????????????
|
TiN_EE
Yes, that TiN
- Total Posts : 377
- Reward points : 0
- Joined: 2010/01/22 21:30:49
- Location: xDevs.com
- Status: offline
- Ribbons : 14
Re: dark x299 and seensors
2019/05/06 01:14:27
(permalink)
They both do. DIMM 0/1 show memory voltage on the left side (near rear I/O) and 2/3 shows right side (near power connectors).
Each side use independent power regulator and can be controlled separately in BIOS.
If you have question, please post in public forum. I do not reply PMs, so all in community can benefit the answer.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/05/06 01:21:18
(permalink)
obi but we have 4 sensor which is true ?
this 2 on up or 2 on down ?
|
TiN_EE
Yes, that TiN
- Total Posts : 377
- Reward points : 0
- Joined: 2010/01/22 21:30:49
- Location: xDevs.com
- Status: offline
- Ribbons : 14
Re: dark x299 and seensors
2019/05/06 01:31:58
(permalink)
Difference is within margin of error +/-5%. If you want accurate voltage down to millivolt, you'll have to use DMM (that's not just for EVGA HW, but for any PC hardware).
If you have question, please post in public forum. I do not reply PMs, so all in community can benefit the answer.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/05/06 01:40:26
(permalink)
and last question where i find spread spectrum ? is on bios or no
|
TiN_EE
Yes, that TiN
- Total Posts : 377
- Reward points : 0
- Joined: 2010/01/22 21:30:49
- Location: xDevs.com
- Status: offline
- Ribbons : 14
Re: dark x299 and seensors
2019/05/06 01:54:18
(permalink)
There is no SS setting available in BIOS, it's always on.
If you have question, please post in public forum. I do not reply PMs, so all in community can benefit the answer.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/05/06 01:57:42
(permalink)
it's bad for this, some times my frequency going up to 4.789 and voltage up to 1.281 or going dow to 4.679, normal stable is 4.7 1.265V, temps is under 78C for full load
post edited by lmatyja - 2019/05/06 02:02:38
|
TiN_EE
Yes, that TiN
- Total Posts : 377
- Reward points : 0
- Joined: 2010/01/22 21:30:49
- Location: xDevs.com
- Status: offline
- Ribbons : 14
Re: dark x299 and seensors
2019/05/06 02:06:25
(permalink)
You can bump BCLK to 100.2 in BIOS to get even numbers for frequency. Clock spread spectrum improve EMI/RFI issues, that's why this was designed in for modern CPU/GPUs.
post edited by TiN_EE - 2019/05/06 02:10:16
If you have question, please post in public forum. I do not reply PMs, so all in community can benefit the answer.
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/05/06 02:07:16
(permalink)
|
lmatyja
Superclocked Member
- Total Posts : 180
- Reward points : 0
- Joined: 2017/10/14 08:45:06
- Status: offline
- Ribbons : 1
Re: dark x299 and seensors
2019/05/06 04:57:33
(permalink)
not hlep this, is but is not now 4789 now is 4749 :)
|