Can we get hotkey for profiles in flow control like we have in OCX for profiles? 

I just got an EVGA clc 280 and installed it in my system yesterday. The Flow software does not read my CPU temperature and any time I try to interact with any part of the software that is supposed to use CPU temp to modify behavior it instantly crashes. The device was recognized fine and installed fine with no issues, the pump runs at full speed and the fans are spinning up and down as intended however this leaves me unable to make a custom fan curve based on CPU temps (the one that makes the most sense) without plugging the fans directly into my mobo and bypassing the FLOW software entirely. The preset fan curve is slightly too aggressive for my tastes, I find this to be annoying, and I would like to see this software interact with my system properly. 
 
Ryzen 1700 @ 3.7ghz (1.275v)
MSI x370 Gaming pro carbon (plugged into CPU_fan1 running in PWN mode at manual 100%, fans plugged into the clc itself.)
16 gb ddr4 2933 cl14
MSI gtx 1070 gaming X

DTurenne
Just going to throw my new problem in here. Hopefully it'll do some good to the development team.
I have an EVGA 1080 ti FTW3 and a CLC 280. At first I was just setting the lighting manually on both using Precision XOC and Flow Control respectively but then LED Sync was released but only detected GPU.
Now, a short time later, it detects both gpu and clc but only if Flow Control is not running. If I attempt to run Flow Control while LED Sync is running I get the CPUWB "device not found" error while if I run Flow Control first and then open LED Sync, my cooler doesn't show up for synchronization.
So I can basically have control of my fans and pump speeds or I can sync my lights. Not both.

It should also be noted that I have g.skill trident z rgb ram on a x99 sabertooth motherboard running g.skills lighting software which does come along with its own problems. Non of which, I believe, should be effecting the issues at hand.

I don't have your exact CLC but this is my issue, same graphics card. am trying to downgrade precision OC software version as suggested in this thread. 120mm clc from evga

scarface9636
so ive read alot and it seems like the software cant read fan speeds or cpu temps on a ryzen based system. is that right? if so thats a pretty big oversight.

Still waiting for this :(

zoglog
Any updating coming? 
 
I haven't been able to use the waterblock software since the new LED update on precision. It refuses to detect my CLC

And this!

I am having the exact problem. how do i get the previous version?

I am running a Z270 MB, (2) 1070ti's in SLI and getting the same issue (device not found)  I have current Precision XOC and DG Tuner running as well.  Everything works but the Flow COntrol Software.

I have tried that and makes no difference. Uninstalled and reinstalled all EVGA software...makes no difference...I know it's seen because LED sync works

Still conflicting with the latest XOC and LED sync. Whenever I boot up it says device not found. I have to physically unplug and plug back in the usb cable.
 
It's silly these programs still essentially have the same issue with LED sync where you either have to choose LED sync or actual control of your waterblock/rad fans. Pretty annoying since on the 7700 the default auto fan curve ramps it up to an unbearable noise by default.

Get the CPUWB device not found error box every 1st time I try to load the software after a bootup with the latest version. The second time it works correctly. Any idea why this would occur?

fearpoint
Get the CPUWB device not found error box every 1st time I try to load the software after a bootup with the latest version. The second time it works correctly. Any idea why this would occur?

I've been getting the same thing.  A restart of the app fixes it for me as well.
 

Where is this option? "

• Added an option to select fan curve based on CPU temperature or coolant temperature"

 
I'm running version 2.0.7 ... CPU temp is still wrong for AMD Ryzen cpu with it's (stupid) built in 20C offset. And this throws the whole CPU Curve off.  Could you (beg) please add a field in options for CPU Off Set. 
 
Nigel.

You're absolutely right about the 60 degree K threshold.   These fans are way too loud when gaming or encoding video.  Cannot recommended to others.
 

Phil2940
1) My custom curbe (profil2) doesn't work normaly, the  fan turn at 2500rpm / default curbe (profil1) 1500rpm in game at 57°C at the same time   (screens tress test join : same result in game at 57°C)  
 ive got a helicopter on my office  for less 100$ (noise) 
 Problem with your max T° target: 60°C   or your software?????
 
2) after one hour of play, although the temperature of the cpu falls to 35 ° C, the fan continues to rotate at 1500rpm  (screen join)  

Hello everyone,
 
Using CLC 280 on a ASUS Maximus Code X, 8086k cpu, Windows 10 1809 update.
If FlowControl starts automatically with Windows I get a CPUWB Device Not Found message. If I try to manually load FlowControl it works. Using FlowControl 2.0.9.0 - Firmware 2.10.0.0
 
I tried to use plug the pump even on different USB ports (instead of the internal USB), same issue. If manually started, it works as intended, if Windows starts it automatically at boot, it fails to load. Its really annoying to manually load it every time I turn on the computer - this is definitely a EVGA FlowControl software issue with Windows 10 1809. EVGA, could you please fix this issue?
 
I already have a ticket open with EVGA support, but its being a painful process so far as all the information requested was superficial and not logs or anything that could help debug the issue were not required so far. So looks like a guessing game - try this, try that, .... same results. Ins't it better to gather logs and have a software engineer to analyse it?