Xmp Profile was designed for a stock clocked cpu.

I got a problem with the last few bios update, including this one.
Sometime, no matter what CPU voltage I choose in bios, after get into Windows, open CPU-Z, my voltage auto bumped up to 1.564V. Don't know if it is problem on my board or bios.

Any comment? Suggestion?

i7 920 on EVGA X58 Micro ATX.

schumi69

Went to update last night and it did not take and now I have to RMA the motherboard. :( at least EVGA has the best warranty in the biz and advanced RMA. 

UPDATE I just want to say that it was not the MB it was the powersupply that failed at that moment. So I had to RMA the powersupply to Thermaltake. I am glad they have a 3 year warranty. :)

Mother Board ( EVGA X58 Micro ATX E-756 )                                                       
Bios ( 51 )                                                                                                     
CPU ( 920 DO )               
CPU Cooler ( Corsair H50 )
Memory (Corsair 1600 8 8 8 24 )
PSU ( Corsair HX620W )
GPU ( XFX 5770 )                                                              
Operating System ( Windows 7 64 Professional )

Frequency Control
CPU Clock Ratio ( 20X )                                                                                         
CPU Host Frequency (Mhz) ( 201)                                                                      
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) (  { 16X } )                                                
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )

Memory Feature        
Memory Speed (Standard)
Memory Control Setting ( Enabled )
Memory Frequency (  2:8 )                                                                
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( Auto )
tCL Setting ( 8 )
tRCD Setting ( 8 )
tRP Setting ( 8 )
tRAS Setting ( 24 )
tRFC Setting ( 88 )
Command Rate ( 1t )


Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.2875 )                                                                                               
CPU VTT Voltage ( +200 )
CPU PLL VCore ( Auto)
DIMM Voltage ( 1.65 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( Auto )
IOH VCore ( Auto )
IOH/ICH I/O Voltage ( Auto )
ICH VCore ( Auto )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Disabled )
CxE Function ( Auto )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s )
OC Recovery ( Disabled )
Turbo Performance ( Disabled )
PnP/PCI     PCI Express
Maximum Payload Size ( 128 ) 
 
Power Management Setup
ACPI Suspend Type ( S1 (POS) )   
HPET Support ( Enabled )     
HPET Mode ( 64-bit )

Randomly bump up my cpu voltage to 1.5-1.6v range as if i set the voltage range is in 1.26 to 1.275v. Tried a lot of voltage setting, couldn't get it stable even with excessive voltage than it needs when I used the cpu on another board. I want to RMA the board because i never have it run stable on this board; however, I can't point out where it has problem. =/ The same setting sometimes passes IBT,sometime not......Not a memory issue for use as I tried to run below the spec.

Hello Comrades,

next week i´ll get my hands on a xeon w3680 processor.
will there be any problems with my 760 mobo? bios version = No.51

there are rumors at www, that only desktop version i7 980 is supported (at the moment).
if so, is there any beta bios released yet?

thanks in advance & sorry for my broken english ;)

just get the latest bios and run with it.

Updated just now for like no reason (E758), everything seems to be perfectly fine so far.

I have a question for EVGA when are they planing on making a bios ONLY for QUAD core cpu as all the bios after S61J do not work correctly with my setup and I know I am not the only one ? I know that six cores are  new and all but don't forget about all your QUAD core users plz