EVGA

EVGA X299 DARK...external I/O shield is designed to fit over the pre-installed shield

Author
Post
Essentials Only Full Version
zerocool101
iCX Member
  • Total Posts : 473
  • Reward points : 0
  • Joined: 2006/04/18 20:05:33
  • Location: Wisconsin
  • Status: offline
  • Ribbons : 1
2018/12/10 19:01:37 (permalink)
Question on the below when installing mobo in a case.. what have people done so far? Did you take the pre-installed I/O shield off before installing the external I/O shield. I can't believe the alligment would be good with the added thickness. Asking before I build my PC this weekend.
 
The motherboard kit comes with an internal and external I/O shield 
 
The external I/O shield is designed to fit over the pre-installed shield, so you will not normally need to remove the pre-installed I/O shield.
post edited by zerocool101 - 2018/12/10 19:51:01

13900KS on Z690 Dark KP
FE 4090
#1

3 Replies Related Threads
    bcavnaugh
    The Crunchinator
    • Total Posts : 38516
    • Reward points : 0
    • Joined: 2012/09/18 17:31:18
    • Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
    • Status: offline
    • Ribbons : 282
    Re: EVGA X299 DARK...external I/O shield is designed to fit over the pre-installed shield 2018/12/10 19:39:33 (permalink)
    I left mine as is and snapped the back I/O Shield in place in the Case, no issue at all to note.
    A known issue with some X299 Dark Motherboards is some Battery are Bad and should be replaced before you install it.
    You have to remove the Chipset Cooler Cover to change the battery and need to remove some screws on the Back Side of the MB.

    post edited by bcavnaugh - 2018/12/16 17:12:02

    Associate Code: 9E88QK5L7811G3H


     
    #2
    PINKTULIP
    SSC Member
    • Total Posts : 698
    • Reward points : 0
    • Joined: 2007/06/03 16:01:19
    • Location: EARTH
    • Status: offline
    • Ribbons : 7
    Re: EVGA X299 DARK...external I/O shield is designed to fit over the pre-installed shield 2018/12/10 19:48:25 (permalink)
    zerocool101
    Question on the below when instaling mobol in a case.. what have people done so far? Did you take the pre-installed I/O shield off before installing the external I/O shield. I can't believe the alligment would be good with the added thickness. Asking before I build my PC this weekend.
     
    The motherboard kit comes with an internal and external I/O shield 
     
    The external I/O shield is designed to fit over the pre-installed shield, so you will not normally need to remove the pre-installed I/O shield.


    yes but it's little tough to fit in there, I had to remove padding from I/O

    MOBO :EVGA X299 DARK 151-SX-E299-KR  BIOS :1.29 CPU : Intel Core i9-10900X Skylake-X 10-Core 3.7 GHz  LCR :Corsair Hydro Series H80i V2 GPU :SAPPHIRE NITRO+ RX 6900 XT SE MEMORY: CORSAIR Dominator Platinum SE Torque 32GB (4 x 8GB) CMD32GX4M4C3200C14T SSD 01: SAMSUNG 970 PRO M.2 1TB NVMe SSD 02: SAMSUNG 860 PRO 256GBX2 Raid 0 PSU : Seosonic Prime Titanium SSR-1000TR 1000 Watts CASE :Thermaltake (Armor+) VH6000SWA SC :Creative Sound Blaster AE-9 5.1 Channels Monitor  Acer XR382CQK  IPS 3840x1600 @ 75HZ BD [/
    #3
    startekselva
    iCX Member
    • Total Posts : 300
    • Reward points : 0
    • Joined: 2018/10/23 00:47:45
    • Status: offline
    • Ribbons : 6
    Re: EVGA X299 DARK...external I/O shield is designed to fit over the pre-installed shield 2018/12/10 20:55:27 (permalink)
    the preinstalled io shield will hold the Wifi antenna IPEX Connector and you can install the provided io shield to cover the screw hold the IPEX Connector




    #4
    Jump to:
  • Back to Mobile