degenerate
SSC Member
- Total Posts : 614
- Reward points : 0
- Joined: 2013/08/23 05:38:31
- Status: offline
- Ribbons : 0
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 01:33:11
(permalink)
emmett
degenerate
Ok so then can someone explain to me this chart on the guide page that specifies all 3 BIOS' as having a 360W power limit? I must be misunderstanding something...
The 360 watts is at default 100%
44% of 360 watts is 158.4
so 144% on slider is 518 watts
at least this is how i understood it.
Okay yeah that makes sense, but maybe mention that somewhere in the guide or in the graph for the apparent dunces like me lol. I looked at it and interpreted it as a 360W limit @ 144%. I did always think that was odd... guess I didn't think hard enough.  I haven't played with my KPE to the point where it would need to draw that much so don't really see more than 390W peaks in HWiNFO64.
 |5900x|MSI B550 Unify-X|2x16GB G.Skill 3800 C14 @ 1900 FCLK|2TB WD SN850 M.2|EVGA 3090 KPE|EVGA 1600T2|Alienware '25' & LG 48" CX OLED|
|
TwoEvilOne
SSC Member
- Total Posts : 716
- Reward points : 0
- Joined: 2018/06/12 10:55:57
- Location: NW Ohio. EVGA Associate Code: 2QME1VF65K9ZY8B
- Status: offline
- Ribbons : 4
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 01:45:43
(permalink)
|
degenerate
SSC Member
- Total Posts : 614
- Reward points : 0
- Joined: 2013/08/23 05:38:31
- Status: offline
- Ribbons : 0
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 01:49:18
(permalink)
Yeah, IIRC even TiN/Vince mentioned the 500W in one of the preview videos in Taiwan. That's why I thought it was odd when I looked at that chart.
Maybe if I had been pushing my card harder I would've noticed, investigated and been able to put 2 & 2 together lol...
|5900x|MSI B550 Unify-X|2x16GB G.Skill 3800 C14 @ 1900 FCLK|2TB WD SN850 M.2|EVGA 3090 KPE|EVGA 1600T2|Alienware '25' & LG 48" CX OLED|
|
Bepzinky
iCX Member
- Total Posts : 281
- Reward points : 0
- Joined: 2016/04/30 13:15:31
- Status: offline
- Ribbons : 2
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 02:14:48
(permalink)
Yes but the card also seems to have kind of hardware limit built in (eeprom)? I've flashed the LN2 BIOS to the OC one to be able to set fans to 100% but it was already hitting PL at ~420W.
|
sparetimepc
CLASSIFIED Member
- Total Posts : 2413
- Reward points : 0
- Joined: 2009/11/13 09:24:09
- Location: Altona, IL
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 04:05:42
(permalink)
I wonder if these results reflect using the Classified Tool while benching or if these results were aquired with just using voltages and boost curves in the factory bios specs.
Attached Image(s)
|
johnksss
CLASSIFIED Member
- Total Posts : 3567
- Reward points : 0
- Joined: 2008/06/21 10:18:46
- Location: Orange County, California
- Status: offline
- Ribbons : 3
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:00:23
(permalink)
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
MSI MEG Z690 UNIFY-X | I9-12900K | 32GB G.Skill Trident Z5 6400Mhz | 1600W EVGA T2 | EVGA 3090 K|ngP|n | Custom Water Cooling Loop | Praxis Wet Bench SX Pro - Flat Edition
HWBOT-PROFILE
|
bcavnaugh
The Crunchinator
- Total Posts : 38516
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:14:10
(permalink)
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
It is for a KP Card not that other FTW3 Card  But then you could just lay your RGB Strip on the Motherboard Under the Hydro Copper giving you have room. What Thermal Pads and TIM are you going with?
post edited by bcavnaugh - 2019/06/03 10:18:34
|
AHowes
CLASSIFIED ULTRA Member
- Total Posts : 6502
- Reward points : 0
- Joined: 2005/09/20 15:38:10
- Location: Macomb MI
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:17:19
(permalink)
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now? Planned on adding my own anyways.
Intel i9 9900K @ 5.2Ghz Single HUGE Custom Water Loop. Asus Z390 ROG Extreme XI MB G.Skill Trident Z 32GB (4x8GB) 4266MHz DDR4 EVGA 2080ti K|NGP|N w/ Hydro Copper block. 34" Dell Alienware AW3418DW 1440 Ultra Wide GSync Monitor Thermaltake Core P7 Modded w/ 2x EK Dual D5 pump top,2 x EK XE 480 2X 360 rads.1 Corsair 520 Rad.
|
Zeddivile
SSC Member
- Total Posts : 761
- Reward points : 0
- Joined: 2017/09/30 11:15:15
- Location: @ the tipity top of FPS mountain
- Status: offline
- Ribbons : 7
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:20:52
(permalink)
Thermal pads already pre orientated on the HC block is what I thought? I am going to start with kryonaut and see how it goes as always. Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping. @ johnksss for anti condensate I was just going to vaso. Thinking of doing more?
post edited by Zeddivile - 2019/06/03 10:23:02
"This stuff breaks my tiny often dehydrated and carb deprived hamster brain" -2019  
|
HawkOculus
iCX Member
- Total Posts : 456
- Reward points : 0
- Joined: 2019/04/10 10:50:51
- Status: offline
- Ribbons : 1
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:23:02
(permalink)
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
Yeah, pads already installed on the block. I won’t be swapping them. Just gonna use Kryonaut as well. I have some NT-1 as well but just gonna use the Grizzly.
|
bcavnaugh
The Crunchinator
- Total Posts : 38516
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:31:03
(permalink)
AHowes
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now?
Planned on adding my own anyways.
Where is this Strip on the FTW3 Hydro Copper Water Block?
|
bcavnaugh
The Crunchinator
- Total Posts : 38516
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:36:04
(permalink)
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
What brand of vaso?
|
AHowes
CLASSIFIED ULTRA Member
- Total Posts : 6502
- Reward points : 0
- Joined: 2005/09/20 15:38:10
- Location: Macomb MI
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:48:02
(permalink)
bcavnaugh
AHowes
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now?
Planned on adding my own anyways.
Where is this Strip on the FTW3 Hydro Copper Water Block?
From memory it was under the area with the water line connections. That's the area where the rgb cable comes out of the block to connect to the card.
Intel i9 9900K @ 5.2Ghz Single HUGE Custom Water Loop. Asus Z390 ROG Extreme XI MB G.Skill Trident Z 32GB (4x8GB) 4266MHz DDR4 EVGA 2080ti K|NGP|N w/ Hydro Copper block. 34" Dell Alienware AW3418DW 1440 Ultra Wide GSync Monitor Thermaltake Core P7 Modded w/ 2x EK Dual D5 pump top,2 x EK XE 480 2X 360 rads.1 Corsair 520 Rad.
|
johnksss
CLASSIFIED Member
- Total Posts : 3567
- Reward points : 0
- Joined: 2008/06/21 10:18:46
- Location: Orange County, California
- Status: offline
- Ribbons : 3
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:52:34
(permalink)
bcavnaugh
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
It is for a KP Card not that other FTW3 Card
But then you could just lay your RGB Strip on the Motherboard Under the Hydro Copper giving you have room.
What Thermal Pads and TIM are you going with?
And have water drip on it. That's a big 10/4 negative! :D But, that was close to my idea though. Only attach it to the bottom of the card. (Provided it does not already have lighting) AHowes
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now?
Planned on adding my own anyways.
Not sure. But I will check that out first. it has an 8 pin plug, but I also see two set of wires. One set going to the OLED and the other set going somewhere into the block.... Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
Vaso is the way to go for sure. Just looking at possible other spots for run off. HawkOculus
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
Yeah, pads already installed on the block. I won’t be swapping them. Just gonna use Kryonaut as well. I have some NT-1 as well but just gonna use the Grizzly.
Same here, no pad swap as of yet. In other news(For everyone else), it does come with pads preinstalled. bcavnaugh
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
What brand of vaso?
What brand do you use?
MSI MEG Z690 UNIFY-X | I9-12900K | 32GB G.Skill Trident Z5 6400Mhz | 1600W EVGA T2 | EVGA 3090 K|ngP|n | Custom Water Cooling Loop | Praxis Wet Bench SX Pro - Flat Edition
HWBOT-PROFILE
|
onMute
New Member
- Total Posts : 84
- Reward points : 0
- Joined: 2017/03/12 06:19:41
- Status: offline
- Ribbons : 1
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 10:55:23
(permalink)
HawkOculus
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
Yeah, pads already installed on the block. I won’t be swapping them. Just gonna use Kryonaut as well. I have some NT-1 as well but just gonna use the Grizzly.
I’ll be using grizzly as well.
|
bcavnaugh
The Crunchinator
- Total Posts : 38516
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 11:07:37
(permalink)
johnksss
bcavnaugh
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
It is for a KP Card not that other FTW3 Card
But then you could just lay your RGB Strip on the Motherboard Under the Hydro Copper giving you have room.
What Thermal Pads and TIM are you going with?
And have water drip on it. That's a big 10/4 negative! :D
But, that was close to my idea though. Only attach it to the bottom of the card. (Provided it does not already have lighting)
AHowes
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now?
Planned on adding my own anyways.
Not sure. But I will check that out first. it has an 8 pin plug, but I also see two set of wires. One set going to the OLED and the other set going somewhere into the block....
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
Vaso is the way to go for sure. Just looking at possible other spots for run off.
HawkOculus
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
Yeah, pads already installed on the block. I won’t be swapping them. Just gonna use Kryonaut as well. I have some NT-1 as well but just gonna use the Grizzly.
Same here, no pad swap as of yet.
In other news(For everyone else), it does come with pads preinstalled.
bcavnaugh
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
What brand of vaso?
What brand do you use?
I do not have any to say as why I asked.
|
johnksss
CLASSIFIED Member
- Total Posts : 3567
- Reward points : 0
- Joined: 2008/06/21 10:18:46
- Location: Orange County, California
- Status: offline
- Ribbons : 3
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 11:59:54
(permalink)
bcavnaugh
johnksss
bcavnaugh
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
It is for a KP Card not that other FTW3 Card
But then you could just lay your RGB Strip on the Motherboard Under the Hydro Copper giving you have room.
What Thermal Pads and TIM are you going with?
And have water drip on it. That's a big 10/4 negative! :D
But, that was close to my idea though. Only attach it to the bottom of the card. (Provided it does not already have lighting)
AHowes
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now?
Planned on adding my own anyways.
Not sure. But I will check that out first. it has an 8 pin plug, but I also see two set of wires. One set going to the OLED and the other set going somewhere into the block....
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
Vaso is the way to go for sure. Just looking at possible other spots for run off.
HawkOculus
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
Yeah, pads already installed on the block. I won’t be swapping them. Just gonna use Kryonaut as well. I have some NT-1 as well but just gonna use the Grizzly.
Same here, no pad swap as of yet.
In other news(For everyone else), it does come with pads preinstalled.
bcavnaugh
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
What brand of vaso?
What brand do you use?
I do not have any to say as why I asked.
I said that because I thought it was a trick question. :D Wasn't really sure how many different people made it. :D
MSI MEG Z690 UNIFY-X | I9-12900K | 32GB G.Skill Trident Z5 6400Mhz | 1600W EVGA T2 | EVGA 3090 K|ngP|n | Custom Water Cooling Loop | Praxis Wet Bench SX Pro - Flat Edition
HWBOT-PROFILE
|
sparetimepc
CLASSIFIED Member
- Total Posts : 2413
- Reward points : 0
- Joined: 2009/11/13 09:24:09
- Location: Altona, IL
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 12:05:15
(permalink)
So is anyone going to upload photos of the GPU with Vaseline applied, I would like to see
|
johnksss
CLASSIFIED Member
- Total Posts : 3567
- Reward points : 0
- Joined: 2008/06/21 10:18:46
- Location: Orange County, California
- Status: offline
- Ribbons : 3
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 12:08:07
(permalink)
dwexpress
So is anyone going to upload photos of the GPU with Vaseline applied, I would like to see
Yes, I'll take some when I do mine in a few hours. need to go get my new headlights and grill and drop them off at paint.
MSI MEG Z690 UNIFY-X | I9-12900K | 32GB G.Skill Trident Z5 6400Mhz | 1600W EVGA T2 | EVGA 3090 K|ngP|n | Custom Water Cooling Loop | Praxis Wet Bench SX Pro - Flat Edition
HWBOT-PROFILE
|
sparetimepc
CLASSIFIED Member
- Total Posts : 2413
- Reward points : 0
- Joined: 2009/11/13 09:24:09
- Location: Altona, IL
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 12:16:05
(permalink)
johnksss
dwexpress
So is anyone going to upload photos of the GPU with Vaseline applied, I would like to see
Yes, I'll take some when I do mine in a few hours. need to go get my new headlights and grill and drop them off at paint.
I have never had issues with condensation before but with a chiller I can surely see it happening
|
bcavnaugh
The Crunchinator
- Total Posts : 38516
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 12:22:39
(permalink)
johnksss
bcavnaugh
johnksss
bcavnaugh
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
It is for a KP Card not that other FTW3 Card
But then you could just lay your RGB Strip on the Motherboard Under the Hydro Copper giving you have room.
What Thermal Pads and TIM are you going with?
And have water drip on it. That's a big 10/4 negative! :D
But, that was close to my idea though. Only attach it to the bottom of the card. (Provided it does not already have lighting)
AHowes
johnksss
Got my shiny new water block today. :)
Looking it over to see about prepping for condensation.
Preliminary inspection reveals no where to just slide the led strip in.
Read reports both ways if it had a led strip or not.. last word was it did have rgb lighting. So no lights now?
Planned on adding my own anyways.
Not sure. But I will check that out first. it has an 8 pin plug, but I also see two set of wires. One set going to the OLED and the other set going somewhere into the block....
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
Vaso is the way to go for sure. Just looking at possible other spots for run off.
HawkOculus
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
Yeah, pads already installed on the block. I won’t be swapping them. Just gonna use Kryonaut as well. I have some NT-1 as well but just gonna use the Grizzly.
Same here, no pad swap as of yet.
In other news(For everyone else), it does come with pads preinstalled.
bcavnaugh
Zeddivile
Thermal pads already pre orientated on the HC block is what I thought?
I am going to start with kryonaut and see how it goes as always.
Speaking of that was sad to not find any traces of KPX when I tore the KPE down. Guess no one played with my card prior to shipping.
@johnksss
for anti condensate I was just going to vaso. Thinking of doing more?
What brand of vaso?
What brand do you use?
I do not have any to say as why I asked.
I said that because I thought it was a trick question. :D
Wasn't really sure how many different people made it. :D
Not sure why you think this was a trick question but OK. I found 8 different types and 4 different brand names. Enjoy your card.
post edited by bcavnaugh - 2019/06/03 12:28:46
|
johnksss
CLASSIFIED Member
- Total Posts : 3567
- Reward points : 0
- Joined: 2008/06/21 10:18:46
- Location: Orange County, California
- Status: offline
- Ribbons : 3
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:04:53
(permalink)
Because vaso stands for Vaseline and last i checked there was only one Vaseline company. Petroleum jelly is made by many. Thanks. I will enjoy my card.
post edited by johnksss - 2019/06/03 13:12:20
MSI MEG Z690 UNIFY-X | I9-12900K | 32GB G.Skill Trident Z5 6400Mhz | 1600W EVGA T2 | EVGA 3090 K|ngP|n | Custom Water Cooling Loop | Praxis Wet Bench SX Pro - Flat Edition
HWBOT-PROFILE
|
sparetimepc
CLASSIFIED Member
- Total Posts : 2413
- Reward points : 0
- Joined: 2009/11/13 09:24:09
- Location: Altona, IL
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:16:38
(permalink)
So it seems dielectric grease would be a good alternative to Vaseline then
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 31041
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 123
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:21:04
(permalink)
dwexpress
So it seems dielectric grease would be a good alternative to Vaseline then
Depends on how hard it would be to remove & knowing none of the ingredients would attack the PCB or plastic parts on the board
Learn your way around the EVGA Forums, Rules & limits on new accounts Ultimate Self-Starter Thread For New Members
I am a Volunteer Moderator - not an EVGA employee
Older RIG projects RTX Project Nibbler
When someone does not use reason to reach their conclusion in the first place; you can't use reason to convince them otherwise!
|
johnksss
CLASSIFIED Member
- Total Posts : 3567
- Reward points : 0
- Joined: 2008/06/21 10:18:46
- Location: Orange County, California
- Status: offline
- Ribbons : 3
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:23:45
(permalink)
I haven't use Dielectric grease in quite some time. I remember using that for the sockets back in the day. But now I just use Vaseline everywhere.
MSI MEG Z690 UNIFY-X | I9-12900K | 32GB G.Skill Trident Z5 6400Mhz | 1600W EVGA T2 | EVGA 3090 K|ngP|n | Custom Water Cooling Loop | Praxis Wet Bench SX Pro - Flat Edition
HWBOT-PROFILE
|
sparetimepc
CLASSIFIED Member
- Total Posts : 2413
- Reward points : 0
- Joined: 2009/11/13 09:24:09
- Location: Altona, IL
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:25:45
(permalink)
Cool GTX
dwexpress
So it seems dielectric grease would be a good alternative to Vaseline then
Depends on how hard it would be to remove & knowing none of the ingredients would attack the PCB or plastic parts on the board
Yeah I don't see how it could be any worse to remove then Vaseline but it's actually design is for repel of moisture and corrosion and it's not electric conducting. Either way I'm sure any warranty would go bye bye after it's applied.
post edited by dwexpress - 2019/06/03 13:30:42
|
Zeddivile
SSC Member
- Total Posts : 761
- Reward points : 0
- Joined: 2017/09/30 11:15:15
- Location: @ the tipity top of FPS mountain
- Status: offline
- Ribbons : 7
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:29:53
(permalink)
I use original formula original manufacturer. Wondering if system would run cooler if I used the Vic's vapor rub edition? lulz. Good ol original vasoline FTW.r Seriously please no one try Vapor rub. That is just a silly thought. Wifey walks in. "Why does your bench smell like eucalyptus ?" "That's because its spa day for the KPE"
post edited by Zeddivile - 2019/06/03 13:33:25
"This stuff breaks my tiny often dehydrated and carb deprived hamster brain" -2019
|
sparetimepc
CLASSIFIED Member
- Total Posts : 2413
- Reward points : 0
- Joined: 2009/11/13 09:24:09
- Location: Altona, IL
- Status: offline
- Ribbons : 27
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:32:59
(permalink)
Zeddivile
I use original formula original manufacturer.
Wondering if system would run cooler if I used the Vic's vapor rub edition? lulz. Good ol original vasoline FTW.r
Seriously please no one try Vapor rub. That is just a silly thought.
Yeah the Vic's vapor rub probably better yet, break up the congestion and let that video card breath
|
bcavnaugh
The Crunchinator
- Total Posts : 38516
- Reward points : 0
- Joined: 2012/09/18 17:31:18
- Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
- Status: offline
- Ribbons : 282
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 13:54:48
(permalink)
|
Crimsonghost99
New Member
- Total Posts : 95
- Reward points : 0
- Joined: 2016/03/18 00:14:45
- Status: offline
- Ribbons : 0
Re: EVGA NVIDIA GeForce RTX 2080 Ti KINGPIN is HERE!
2019/06/03 14:44:25
(permalink)
I bought a tub of Kingpin’s grease shortly after buying the KPE. Will let you guys know what I think of it as I’m out of Kryonaut. Not that I will load mine up anywhere near what you guys will.
|