EVGA

Helpful ReplyEVGA GeForce RTX 3090 FTW3 XOC BIOS

Page: << < ..226227228229230.. > >> Showing page 228 of 240
Author
Post
Essentials Only Full Version
vyoung1337
New Member
  • Total Posts : 4
  • Reward points : 0
  • Joined: 2021/02/03 12:38:34
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 14:04:38 (permalink)
Is the 3090 ftw3 ultra suppose to hit 500w? I emailed 3090oc saying my card can only hit 460w@119% and they say it is not guaranteed to hit 500w, only possible up to. But i feel 460w is so far from 500. What is the stock powerdraw at 100% tdp?
#6811
zaikk
Superclocked Member
  • Total Posts : 111
  • Reward points : 0
  • Joined: 2020/11/22 04:20:40
  • Location: Sweden, Europe
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 15:15:42 (permalink)
vyoung1337
Is the 3090 ftw3 ultra suppose to hit 500w? I emailed 3090oc saying my card can only hit 460w@119% and they say it is not guaranteed to hit 500w, only possible up to. But i feel 460w is so far from 500. What is the stock powerdraw at 100% tdp?



With the XOC bios 480-500 watts. 
 
Without 450 watts if I'm not mistaken. I myself are doing a RMA for a replacement card because my pcie slot draw over 80watts and I don't get close to 500 with the XOC bios. I got a maximum of 456 watts, while my pcie slot was drawing 80-81 watts. :/ 

AMD 5950x @4.7 GHZ 1.27 volt
Asus ROG Crosshair VIII Dark Hero
NZXT Kraken z73 360mm aio
4x8 G.Skill TridentZ RGB 4400 mhz cl16 clocked @3800 cl14
EVGA GeForce RTX 3090 24GB FTW3 Ultra
Lian-Li O11 Dynamic case
9x Lian-li SL120 fans
Lian Li Strimer Plus 24-pin
Lian Li Strimer Plus Triple 8-pin
 
#6812
KingEngineRevUp
FTW Member
  • Total Posts : 1030
  • Reward points : 0
  • Joined: 2019/03/28 16:38:54
  • Status: offline
  • Ribbons : 9
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 15:32:34 (permalink)
Guys, a user here did very thorough test using a metered clamp on a 3080 Ti.

It turns out that GPU-Z DOES NOT report power correctly.

https://www.overclock.net....1791823/post-28835729

It is HIGHLY likely that your cards are hitting 500W or close to it, GPU-Z does not accurately depict this.

For those too lazy to click the link, look here at a 3080 Ti.



Note, the 423W on the bottom left doesn't even have the PCI-E connector power added to it either.

This is supp to be a 450W bios, GPU-Z reports 420-425W but in reality it's pulling more, 480W!
post edited by KingEngineRevUp - 2021/07/06 15:37:00

Attached Image(s)

#6813
zaikk
Superclocked Member
  • Total Posts : 111
  • Reward points : 0
  • Joined: 2020/11/22 04:20:40
  • Location: Sweden, Europe
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 15:36:55 (permalink)
KingEngineRevUp
Guys, a user here did very thorough test using a metered clamp on a 3080 Ti.

It turns out that GPU-Z DOES NOT report power correctly.

https://www.overclock.net....1791823/post-28835729

It is HIGHLY likely that your cards are hitting 500W or close to it, GPU-Z does not accurately depict this.

For those too lazy to click the link, look here at a 3080 Ti.





I've checked mine using different methods, and I'm not even close to 500watts. If I'm lucky I get a little brief moment where I hit 450~ ish, but most of the times I'm 60 ish watts away from the golden 500 watts. So I'm going to do the RMA, hopefully it gets better. I got a spare 3080 from my streaming pc I can use whilst waiting for the new card.

AMD 5950x @4.7 GHZ 1.27 volt
Asus ROG Crosshair VIII Dark Hero
NZXT Kraken z73 360mm aio
4x8 G.Skill TridentZ RGB 4400 mhz cl16 clocked @3800 cl14
EVGA GeForce RTX 3090 24GB FTW3 Ultra
Lian-Li O11 Dynamic case
9x Lian-li SL120 fans
Lian Li Strimer Plus 24-pin
Lian Li Strimer Plus Triple 8-pin
 
#6814
KingEngineRevUp
FTW Member
  • Total Posts : 1030
  • Reward points : 0
  • Joined: 2019/03/28 16:38:54
  • Status: offline
  • Ribbons : 9
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 15:37:44 (permalink)
zaikk
KingEngineRevUp
Guys, a user here did very thorough test using a metered clamp on a 3080 Ti.

It turns out that GPU-Z DOES NOT report power correctly.

https://www.overclock.net....1791823/post-28835729

It is HIGHLY likely that your cards are hitting 500W or close to it, GPU-Z does not accurately depict this.

For those too lazy to click the link, look here at a 3080 Ti.





I've checked mine using different methods, and I'm not even close to 500watts. If I'm lucky I get a little brief moment where I hit 450~ ish, but most of the times I'm 60 ish watts away from the golden 500 watts. So I'm going to do the RMA, hopefully it gets better. I got a spare 3080 from my streaming pc I can use whilst waiting for the new card.


What method are you using to check the power draw? Are you using separate measuring equipment that's not software based in your PC?
#6815
talon951
FTW Member
  • Total Posts : 1026
  • Reward points : 0
  • Joined: 2020/10/06 02:41:19
  • Status: offline
  • Ribbons : 3
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 16:04:53 (permalink)
Most of the bios I've checked with ABE show a limit of 78watts on the PCIE slot, so they will stop around 80w probably. So that may be a separate problem. Only other fix is the KP XOC bios but it's not a great daily driver. I think it's limited to 90-100w. Can't remember the exact number.

KingEngineRevUp could be right but there's a decent chance the cards really are gimped. Easy to verify with a $50 clamp meter and some extension cables that allow easy separation of the wires.

The key to getting an RMA is probably showing the card is running above spec which is a potential liability issue for evga. Need to say the correct passphrase when calling evga. Lol

It is interesting the 3080ti runs well above spec on 8pin #2. Although hidden by the readings provided by the card. Helps explain why it runs so hot with the air cooler.
post edited by talon951 - 2021/07/06 16:07:31
#6816
talon951
FTW Member
  • Total Posts : 1026
  • Reward points : 0
  • Joined: 2020/10/06 02:41:19
  • Status: offline
  • Ribbons : 3
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 17:20:11 (permalink)
zaikk
vyoung1337
Is the 3090 ftw3 ultra suppose to hit 500w? I emailed 3090oc saying my card can only hit 460w@119% and they say it is not guaranteed to hit 500w, only possible up to. But i feel 460w is so far from 500. What is the stock powerdraw at 100% tdp?



With the XOC bios 480-500 watts. 
 
Without 450 watts if I'm not mistaken. I myself are doing a RMA for a replacement card because my pcie slot draw over 80watts and I don't get close to 500 with the XOC bios. I got a maximum of 456 watts, while my pcie slot was drawing 80-81 watts. :/ 




Yep, 82w max for the 3090 FTW3 XOC bios (Max Slot PL),
 

#6817
matrix1999
New Member
  • Total Posts : 1
  • Reward points : 0
  • Joined: 2020/11/19 16:49:06
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/06 22:08:05 (permalink)
Hi, newbie here.  My cousin managed to get a 3090 FTW3 Ultra recently and upon booting up the first time, Precision X1 asked him to update the  VBIOS (OC switch position) and now he is running the version 94.02.42.C0.02, whereas I have the same card and yet I am still running 94.02.32.80.27 (also in OC switch position).  Where can I download the BIOS for installation?  I tried rebooting my PC and I am running the latest version of Precision X1 but it doesn't offer me to upgrade the BIOS.
 
Any guidance is much appreciated.
 
#6818
EvgaUser2711201
Superclocked Member
  • Total Posts : 210
  • Reward points : 0
  • Joined: 2017/10/18 14:31:43
  • Location: Canada
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/07 00:56:32 (permalink)
my replacement ftw3 ultra preforms better than my kingpin lol
 


#6819
vyoung1337
New Member
  • Total Posts : 4
  • Reward points : 0
  • Joined: 2021/02/03 12:38:34
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/08 17:18:26 (permalink)
where is the download for this ABE tool available?
#6820
god503
Superclocked Member
  • Total Posts : 126
  • Reward points : 0
  • Joined: 2020/10/15 14:32:40
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/08 20:07:11 (permalink)
I was around when this thread started wayyyyyyy back in October. AND FOR THE LIFE OF ME I CANNOT BELIEVE EVERYONE IS STILL GETTING SUCKERED INTO THE STUPID PCI SLOT POWER DRAW THING OVER AND OVER. ITS BEEN ABOUT 10 MONTHS SINCE THIS CARD HAS BEEN OUT. CAN ANYONE POINT ME TO AT LEAST ONE PERSON WHOS MB FRIED BECAUSE OF THIS PROBLEM.... PLEASE JUST ONE!!!!!. u new guys are getting suckered in by the same people who wasted there time and money on rmas when there was nothing wrong with their cards just so they can justify their own actions. U even have one shmuck who is telling people the "normal" power draw from the slot is 66 watts when pci spec calls for 75... PER SLOT!!!!! Meaning a mobo can handle more to one slot if it needs to. NOONE ON THIS THREAD IS AN ELECTRICAL ENGINEER!!!! JUST ENJOY UR CARD PEOPLE!!!! I have been using the 1k bios since I slapped on an optimus water block in December.... my card sucks down 650 watts and PEAKS AT 103 WATTS AT THE SLOT!!!! GUESS WHAT????? STILL CHUGGING ALONG 7 MONTHS WITH NO ISSUE!!! RED LIPS AND ALL... slaying every game at 4k on max settings with DLSS off!!!

The problem was and still is by the way... heat!!!! Specifically the thermal pads and paste job. They were **** when I took off the fans. And the air cooling is not sufficient at all for this card as well. It definitely holds it back. Get it on water as soon as u can and stop listing to these people on this thread unless they can show you a college degree in electrical engineering or are on the evga design team that made the card.... FYI. I have a chemistry degree... for the record of course
#6821
dbro351
New Member
  • Total Posts : 4
  • Reward points : 0
  • Joined: 2021/06/10 09:01:58
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/08 22:04:33 (permalink)
Thank you EVGA. 4 days from Taipei to me. Card is pulling power as specified and I love it.
Cannot fault their service. Very impressed.
#6822
hallmark888
New Member
  • Total Posts : 76
  • Reward points : 0
  • Joined: 2010/12/16 11:53:36
  • Status: offline
  • Ribbons : 1
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/08 23:20:26 (permalink)
@matrix1999 You have an older revision card that doesn't need the update. 
post edited by hallmark888 - 2021/07/08 23:25:55
#6823
zaikk
Superclocked Member
  • Total Posts : 111
  • Reward points : 0
  • Joined: 2020/11/22 04:20:40
  • Location: Sweden, Europe
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 08:38:15 (permalink)
dbro351
Thank you EVGA. 4 days from Taipei to me. Card is pulling power as specified and I love it.
Cannot fault their service. Very impressed.



Glad to hear! How long did you wait for the RMA approval?

AMD 5950x @4.7 GHZ 1.27 volt
Asus ROG Crosshair VIII Dark Hero
NZXT Kraken z73 360mm aio
4x8 G.Skill TridentZ RGB 4400 mhz cl16 clocked @3800 cl14
EVGA GeForce RTX 3090 24GB FTW3 Ultra
Lian-Li O11 Dynamic case
9x Lian-li SL120 fans
Lian Li Strimer Plus 24-pin
Lian Li Strimer Plus Triple 8-pin
 
#6824
brandondies
New Member
  • Total Posts : 14
  • Reward points : 0
  • Joined: 2018/10/06 15:20:16
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 08:39:42 (permalink)
god503
I was around when this thread started wayyyyyyy back in October. AND FOR THE LIFE OF ME I CANNOT BELIEVE EVERYONE IS STILL GETTING SUCKERED INTO THE STUPID PCI SLOT POWER DRAW THING OVER AND OVER. ITS BEEN ABOUT 10 MONTHS SINCE THIS CARD HAS BEEN OUT. CAN ANYONE POINT ME TO AT LEAST ONE PERSON WHOS MB FRIED BECAUSE OF THIS PROBLEM.... PLEASE JUST ONE!!!!!. u new guys are getting suckered in by the same people who wasted there time and money on rmas when there was nothing wrong with their cards just so they can justify their own actions. U even have one shmuck who is telling people the "normal" power draw from the slot is 66 watts when pci spec calls for 75... PER SLOT!!!!! Meaning a mobo can handle more to one slot if it needs to. NOONE ON THIS THREAD IS AN ELECTRICAL ENGINEER!!!! JUST ENJOY UR CARD PEOPLE!!!! I have been using the 1k bios since I slapped on an optimus water block in December.... my card sucks down 650 watts and PEAKS AT 103 WATTS AT THE SLOT!!!! GUESS WHAT????? STILL CHUGGING ALONG 7 MONTHS WITH NO ISSUE!!! RED LIPS AND ALL... slaying every game at 4k on max settings with DLSS off!!!

The problem was and still is by the way... heat!!!! Specifically the thermal pads and paste job. They were **** when I took off the fans. And the air cooling is not sufficient at all for this card as well. It definitely holds it back. Get it on water as soon as u can and stop listing to these people on this thread unless they can show you a college degree in electrical engineering or are on the evga design team that made the card.... FYI. I have a chemistry degree... for the record of course



Wrong.
#6825
jevy_b
New Member
  • Total Posts : 3
  • Reward points : 0
  • Joined: 2021/05/15 10:11:14
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 10:32:59 (permalink)
dsffsdfsd
god503
I was around when this thread started wayyyyyyy back in October. AND FOR THE LIFE OF ME I CANNOT BELIEVE EVERYONE IS STILL GETTING SUCKERED INTO THE STUPID PCI SLOT POWER DRAW THING OVER AND OVER. ITS BEEN ABOUT 10 MONTHS SINCE THIS CARD HAS BEEN OUT. CAN ANYONE POINT ME TO AT LEAST ONE PERSON WHOS MB FRIED BECAUSE OF THIS PROBLEM.... PLEASE JUST ONE!!!!!. u new guys are getting suckered in by the same people who wasted there time and money on rmas when there was nothing wrong with their cards just so they can justify their own actions. U even have one shmuck who is telling people the "normal" power draw from the slot is 66 watts when pci spec calls for 75... PER SLOT!!!!! Meaning a mobo can handle more to one slot if it needs to. NOONE ON THIS THREAD IS AN ELECTRICAL ENGINEER!!!! JUST ENJOY UR CARD PEOPLE!!!! I have been using the 1k bios since I slapped on an optimus water block in December.... my card sucks down 650 watts and PEAKS AT 103 WATTS AT THE SLOT!!!! GUESS WHAT????? STILL CHUGGING ALONG 7 MONTHS WITH NO ISSUE!!! RED LIPS AND ALL... slaying every game at 4k on max settings with DLSS off!!!

The problem was and still is by the way... heat!!!! Specifically the thermal pads and paste job. They were **** when I took off the fans. And the air cooling is not sufficient at all for this card as well. It definitely holds it back. Get it on water as soon as u can and stop listing to these people on this thread unless they can show you a college degree in electrical engineering or are on the evga design team that made the card.... FYI. I have a chemistry degree... for the record of course



The PCI Express Card Electromechanical Specification Revision 2.0, section 4.2, note 4 states:
A x16 graphics card is limited to 75 W. The 75 W maximum can be drawn via the combination of +12V and +3.3V rails, but each rail draw is limited as defined in Table 4-1, and the sum of the draw on the two rails cannot exceed 75 W.
Table 4-1 states that the maximum current for the 12V power rail on this slot is 5.5 A. That's 66 W.
 
While I am an electronic engineer, I'm not on the EVGA design team that made the card. However - if power draws in excess of 66 W per slot were allowable, why would EVGA allow this as a reason for their special RMA?
 
I would suggest that you reduce your use of capital letters and punctuation, and consider that perhaps you have simply been lucky that you've been able (up till now) to draw 103 W on your PCIe slot without seeing any symptoms of serious damage. If the slot has been rated for certain electrical limits, it will in no way be guaranteed to work outside those limits. It might fail tomorrow; it might fail next year; it might never fail - but by continuing to use it outside its specified operating parameters, you are leaving this entirely to luck.
post edited by jevy_b - 2021/07/09 10:44:00
#6826
god503
Superclocked Member
  • Total Posts : 126
  • Reward points : 0
  • Joined: 2020/10/15 14:32:40
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 18:41:09 (permalink)
Then why would evga put a 10 amp fuse on the pcie slot power line???????? That means u need more than 120 watts to trip it...... and I am not wrong stating the SLOT provides 75 watts. You breaking down where the total come from doesn't change the fact that's its 75 watts. And as an electrician you do know all power specs come with an acceptable 10 percent variance, right???? So that really allows a max of almost 83 watts. So yes. If you say the slot is only 66 watts then your misrepresenting the truth and these gullible children on this tread belive it.
post edited by god503 - 2021/07/09 18:51:01
#6827
god503
Superclocked Member
  • Total Posts : 126
  • Reward points : 0
  • Joined: 2020/10/15 14:32:40
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 18:46:39 (permalink)
brandondies
god503
I was around when this thread started wayyyyyyy back in October. AND FOR THE LIFE OF ME I CANNOT BELIEVE EVERYONE IS STILL GETTING SUCKERED INTO THE STUPID PCI SLOT POWER DRAW THING OVER AND OVER. ITS BEEN ABOUT 10 MONTHS SINCE THIS CARD HAS BEEN OUT. CAN ANYONE POINT ME TO AT LEAST ONE PERSON WHOS MB FRIED BECAUSE OF THIS PROBLEM.... PLEASE JUST ONE!!!!!. u new guys are getting suckered in by the same people who wasted there time and money on rmas when there was nothing wrong with their cards just so they can justify their own actions. U even have one shmuck who is telling people the "normal" power draw from the slot is 66 watts when pci spec calls for 75... PER SLOT!!!!! Meaning a mobo can handle more to one slot if it needs to. NOONE ON THIS THREAD IS AN ELECTRICAL ENGINEER!!!! JUST ENJOY UR CARD PEOPLE!!!! I have been using the 1k bios since I slapped on an optimus water block in December.... my card sucks down 650 watts and PEAKS AT 103 WATTS AT THE SLOT!!!! GUESS WHAT????? STILL CHUGGING ALONG 7 MONTHS WITH NO ISSUE!!! RED LIPS AND ALL... slaying every game at 4k on max settings with DLSS off!!!

The problem was and still is by the way... heat!!!! Specifically the thermal pads and paste job. They were **** when I took off the fans. And the air cooling is not sufficient at all for this card as well. It definitely holds it back. Get it on water as soon as u can and stop listing to these people on this thread unless they can show you a college degree in electrical engineering or are on the evga design team that made the card.... FYI. I have a chemistry degree... for the record of course



Wrong.


Prove me wrong. Show me one board that got cooked because of an evga card. Please. Just one..... 10 months in... I'm sure you can find one board to prove your comment right?????
#6828
arestavo
CLASSIFIED ULTRA Member
  • Total Posts : 6801
  • Reward points : 0
  • Joined: 2008/02/06 06:58:57
  • Location: Through the Scary Door
  • Status: offline
  • Ribbons : 77
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 19:21:52 (permalink)
god503
Then why would evga put a 10 amp fuse on the pcie slot power line???????? That means u need more than 120 watts to trip it...... and I am not wrong stating the SLOT provides 75 watts. You breaking down where the total come from doesn't change the fact that's its 75 watts. And as an electrician you do know all power specs come with an acceptable 10 percent variance, right???? So that really allows a max of almost 83 watts. So yes. If you say the slot is only 66 watts then your misrepresenting the truth and these gullible children on this tread belive it.

If you have a problem with GPU-Z only reading 12V wattage and not 12V + 3V, complain to the GPU-Z folks. Maybe they'll fix whatever it is that prevents them from adding those two values together so we can see >75W being pulled, instead of 83W on 12V  and ~8W on the 3V that we have to assume is ~8W and not more. 
#6829
arestavo
CLASSIFIED ULTRA Member
  • Total Posts : 6801
  • Reward points : 0
  • Joined: 2008/02/06 06:58:57
  • Location: Through the Scary Door
  • Status: offline
  • Ribbons : 77
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 19:25:17 (permalink)
god503
brandondies
god503
I was around when this thread started wayyyyyyy back in October. AND FOR THE LIFE OF ME I CANNOT BELIEVE EVERYONE IS STILL GETTING SUCKERED INTO THE STUPID PCI SLOT POWER DRAW THING OVER AND OVER. ITS BEEN ABOUT 10 MONTHS SINCE THIS CARD HAS BEEN OUT. CAN ANYONE POINT ME TO AT LEAST ONE PERSON WHOS MB FRIED BECAUSE OF THIS PROBLEM.... PLEASE JUST ONE!!!!!. u new guys are getting suckered in by the same people who wasted there time and money on rmas when there was nothing wrong with their cards just so they can justify their own actions. U even have one shmuck who is telling people the "normal" power draw from the slot is 66 watts when pci spec calls for 75... PER SLOT!!!!! Meaning a mobo can handle more to one slot if it needs to. NOONE ON THIS THREAD IS AN ELECTRICAL ENGINEER!!!! JUST ENJOY UR CARD PEOPLE!!!! I have been using the 1k bios since I slapped on an optimus water block in December.... my card sucks down 650 watts and PEAKS AT 103 WATTS AT THE SLOT!!!! GUESS WHAT????? STILL CHUGGING ALONG 7 MONTHS WITH NO ISSUE!!! RED LIPS AND ALL... slaying every game at 4k on max settings with DLSS off!!!

The problem was and still is by the way... heat!!!! Specifically the thermal pads and paste job. They were **** when I took off the fans. And the air cooling is not sufficient at all for this card as well. It definitely holds it back. Get it on water as soon as u can and stop listing to these people on this thread unless they can show you a college degree in electrical engineering or are on the evga design team that made the card.... FYI. I have a chemistry degree... for the record of course



Wrong.


Prove me wrong. Show me one board that got cooked because of an evga card. Please. Just one..... 10 months in... I'm sure you can find one board to prove your comment right?????

Spoiler alert - there are a metric pot ton of EVGA 3090 cards that died. And while I cannot prove that the out of tolerance PCIE power draw is to blame, it very likely is the primary cause. 
 
With that said, it's obvious that you don't care to absorb this. That's perfectly fine, and I'm happily adding you to the ignore list as I'm tired of hearing this disinformation from you.
#6830
god503
Superclocked Member
  • Total Posts : 126
  • Reward points : 0
  • Joined: 2020/10/15 14:32:40
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 19:57:32 (permalink)
The idea was that it would kill the mobo... but we don't have 1 board that was ko'd. Those cards dying could be froem anything. But since u need 120 watts to bust the slot fuse on the card.... doent lead me to belive that had anything to do with it
#6831
dbro351
New Member
  • Total Posts : 4
  • Reward points : 0
  • Joined: 2021/06/10 09:01:58
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/09 20:36:42 (permalink)
zaikk
dbro351
Thank you EVGA. 4 days from Taipei to me. Card is pulling power as specified and I love it.
Cannot fault their service. Very impressed.



Glad to hear! How long did you wait for the RMA approval?

Only about 3-4 days after I sent through screenshots and info to support. I used HWinfo & GPUz for screenshots to record pcie slot draw, each 8 pin power’s, gpu max watts after 3dmark run and benchmarking a couple games.
#6832
vyoung1337
New Member
  • Total Posts : 4
  • Reward points : 0
  • Joined: 2021/02/03 12:38:34
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/10 12:36:05 (permalink)
So with a RMA'ed 3090 ftw3 ultra that couldnt get above 460ish watts at 119%, I flashed to 94.02.42.80.27 and it was able to get to 500w, and pcie slot power <65w which is good and what i was hoping for.

I wonder why the OC bios that came with the RMA card that supposedly has the xoc500w bios on it(94.02.42.c0.02) is capped at like around 110% tdp.  changes from 110%-119% does not make a difference. 
#6833
nuzzlet
New Member
  • Total Posts : 1
  • Reward points : 0
  • Joined: 2021/07/04 15:04:44
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS BETA 2021/07/11 12:27:43 (permalink)
Hey guys, I'm having an issue with my 3090 Ftw3 ultra where for a few milliseconds every few minutes a red light flashes on my GPU.

Any ideas how this can help? I'm having trouble following this forum.
#6834
marcus_andrews
New Member
  • Total Posts : 21
  • Reward points : 0
  • Joined: 2020/09/19 09:01:51
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS BETA 2021/07/11 19:21:09 (permalink)
I just launched precision x1 which needed to upgrade my card's firmware apparently -- do I need to reinstall the bios at all?

CPU: AMD Ryzen 9 5950x
CPU Cooler: Optimus Foundation CPU Block
Mobo: Gigabyte x570 Aorus Xtreme
GPU: EVGA RTX 3090 FTW3 Ultra Gaming
GPU Cooler: Optimus Absolute FTW3 GPU Block
RAM: 64 GB (4x16) G.Skill Trident Z Neo, 3600 MHz CL16
SSDs: 1x 2TB Sabrent Rocket 4 Plus NVMe 4.0 Gen4 PCIe M.2, 2x 2TB Sabrent Rocket NVMe 4.0 Gen4 PCIe M.2, 2x 4TB Samsung 860 EVO
PSU: Seasonic PRIME Ultra Titanium 1000W
Radiators: 3x Hardware Labs Black Ice Nemesis 360GTS
Fans: 10x Noctua NF-A12x25 PWM fans + 10x Phanteks Halos Lux Digital LED 120mm Fan Frames
Reservoir + Pump: Heatkiller Tube 200 D5 + Aquacomputer D5 Next RGB Pump
Coolant + Fittings + Tubing: Koolance 705 Clear coolant, Barrows fittings, EK ZMT tubing
Case: Lian-Li O11 Dynamic XL
Monitor: LG 27GL850-B

#6835
HeinzNeu
New Member
  • Total Posts : 35
  • Reward points : 0
  • Joined: 2013/04/06 10:45:28
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/12 00:51:31 (permalink)
vyoung1337
So with a RMA'ed 3090 ftw3 ultra that couldnt get above 460ish watts at 119%, I flashed to 94.02.42.80.27 and it was able to get to 500w, and pcie slot power <65w which is good and what i was hoping for.

I wonder why the OC bios that came with the RMA card that supposedly has the xoc500w bios on it(94.02.42.c0.02) is capped at like around 110% tdp.  changes from 110%-119% does not make a difference. 

I can confirm all of that.
My new replacement card (EVGA 227, Rev. 3) could not reach 500 watts until I flashed the 94.02.42.80.27.
Iam happy now.

AMD 5950X@EK-Monoblock@ ASUS Crosshair VIII Hero|EVGA FTW3 Ultra Gaming 3090 @H²O_EK_Waterblock H²O@Mo-Ra3|Corsair AV860W|4*8 GB G.Skill@3800 MHz@16-16-16 |Gigabyte Aorus NVMe Gen4| Cooler Master CoSmoS II |LG UltraGear 38GL950G-B, 37.5" |Win 10 Prof. 64 bit
#6836
zaikk
Superclocked Member
  • Total Posts : 111
  • Reward points : 0
  • Joined: 2020/11/22 04:20:40
  • Location: Sweden, Europe
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS 2021/07/12 03:22:49 (permalink)
dbro351
zaikk
dbro351
Thank you EVGA. 4 days from Taipei to me. Card is pulling power as specified and I love it.
Cannot fault their service. Very impressed.



Glad to hear! How long did you wait for the RMA approval?

Only about 3-4 days after I sent through screenshots and info to support. I used HWinfo & GPUz for screenshots to record pcie slot draw, each 8 pin power’s, gpu max watts after 3dmark run and benchmarking a couple games.



I did the same. sent them all of 3090oc@evga.com and now waiting RMA approval. Got my RMA sent late thursday, no response yet so hoping I'll get a response soon.

AMD 5950x @4.7 GHZ 1.27 volt
Asus ROG Crosshair VIII Dark Hero
NZXT Kraken z73 360mm aio
4x8 G.Skill TridentZ RGB 4400 mhz cl16 clocked @3800 cl14
EVGA GeForce RTX 3090 24GB FTW3 Ultra
Lian-Li O11 Dynamic case
9x Lian-li SL120 fans
Lian Li Strimer Plus 24-pin
Lian Li Strimer Plus Triple 8-pin
 
#6837
zaikk
Superclocked Member
  • Total Posts : 111
  • Reward points : 0
  • Joined: 2020/11/22 04:20:40
  • Location: Sweden, Europe
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS BETA 2021/07/12 03:25:21 (permalink)
nuzzlet
Hey guys, I'm having an issue with my 3090 Ftw3 ultra where for a few milliseconds every few minutes a red light flashes on my GPU.

Any ideas how this can help? I'm having trouble following this forum.



Are you using 3 individual pci-e cables from the psu? 1 for each slot?  If so, I have no clue.

AMD 5950x @4.7 GHZ 1.27 volt
Asus ROG Crosshair VIII Dark Hero
NZXT Kraken z73 360mm aio
4x8 G.Skill TridentZ RGB 4400 mhz cl16 clocked @3800 cl14
EVGA GeForce RTX 3090 24GB FTW3 Ultra
Lian-Li O11 Dynamic case
9x Lian-li SL120 fans
Lian Li Strimer Plus 24-pin
Lian Li Strimer Plus Triple 8-pin
 
#6838
zaikk
Superclocked Member
  • Total Posts : 111
  • Reward points : 0
  • Joined: 2020/11/22 04:20:40
  • Location: Sweden, Europe
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS BETA 2021/07/12 06:05:33 (permalink)
Still waiting for my RMA approval for the power draw issues, EU…..

AMD 5950x @4.7 GHZ 1.27 volt
Asus ROG Crosshair VIII Dark Hero
NZXT Kraken z73 360mm aio
4x8 G.Skill TridentZ RGB 4400 mhz cl16 clocked @3800 cl14
EVGA GeForce RTX 3090 24GB FTW3 Ultra
Lian-Li O11 Dynamic case
9x Lian-li SL120 fans
Lian Li Strimer Plus 24-pin
Lian Li Strimer Plus Triple 8-pin
 
#6839
ziems
New Member
  • Total Posts : 6
  • Reward points : 0
  • Joined: 2014/03/14 14:43:32
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3090 FTW3 XOC BIOS BETA 2021/07/12 10:02:17 (permalink)
I've received the shipping confirmation and serial number of the new card today...still Part No. 24G-P5-3987-KR
I thought the reworked PCB cards (rev1) got a new part number?!
 
#6840
Page: << < ..226227228229230.. > >> Showing page 228 of 240
Jump to:
  • Back to Mobile