oh yea, i have windows 7 64-bit

1st Remove all modules and test each one individually in slot one.
If the all work clean the dust bunnies in all dim slots and reinstall.
Make sure when inserting you hear the click both sides.
 
2nd make sure your memory is in the right slot for triple channel that would be slots 1, 3, and 5 see below.
 

Good Luck!

Just so you guys know ( & have forgotten ? )  the memory is dual-channel = DDR 
  It sounds fine to me,... all DDR memory runs "dual-channel"
 When you put 6 sticks in, it isn't going to say sexa-channel , just like it is NOT going to say triple-channel....Doesn't matter how many sticks are in, it will always say dual-channel in the spot you are referring to.
 
My bad, in my haste I did not fully read what you were referring to NOR did I even look at your attached pic...
 I was thinking of Bios boot up post...
 
YES, everyone is right  CPUZ (reskin E-LEET)  will say dual or triple in the area you were referring to in your picture.  Mine also says triple !  

STEVEBABCOCK2002

Just so you guys know ( & have forgotten ? )  the memory is dual-channel = DDR 
It sounds fine to me,... all DDR memory runs "dual-channel"
When you put 6 sticks in, it isn't going to say sexa-channel , just like it is NOT going to say triple-channel....Doesn't matter how many sticks are in, it will always say dual-channel in the spot you are referring to.

DDR = Dual data rate, that has nothing to do with the memory channels.
Triple channel referes to the access mode from the system not the data rate internally of the chip.
 
I'm not sure what you aren't getting triple channel out of it though.  Mine is running in triple channel and I just have 3 sticks.

wow, what the hell is wrong with my system! it says right there, 6gb's and i have it all in slots 1,3, and 5.
 
what do you think it is ?windows 7??? 
 
i'll post after i have a chance to test each memory module. 
 
 

CRAPPPP
 
SO i'm running raid 0 and after i flashed my bios to the newer bios, i ran into some problems!
 
it wont boot up properly. of course i went into the bios and reset it from IDE to RAID again. It gets to the windows 7 logo and then reboots!!! im having windows 7 do that repair right now......see if it fixes it...
 
am i missing something??? hope not.... ****!!!!!

Mine says triple as well. Something is wrong with the board or the CPU. Probably the CPU since it has the memory controller in it. First I will try changing the cpu. But before that. Reset the bios to defaults or remove the battery. 

Set HPET to 64 bit
You cannot load a previously saved BIOS profile after flashing BIOS. If you did that, you need to reset CMOS and start the BIOS settings from scratch.
Regardless you must set all BIOS settings just like you just installed a new mobo.
Do you have a sound card installed? If so, did you disable onboard sound? You have a Windows driver loading that is conflicting with something, and it is due to a BIOS setting.

I had something similar to this happen to me:
I was RMAing my EVGA mobo and had Win7-64 installed on my Kingston V-series SSD. So I kept it for the replacement board (exact same model). In the meantime I used an Asus Rampage II extreme mobo, and used a Velociraptor boot drive with it. But when my EVGA RMA board came, and I tried to boot on the Kingston, it did just like yours is doing (not in RAID, but did have RAID 10 data - WD blacks). The RAID did not matter whether or not they were connected. By that time I had found out that drive did not support TRIM, so I bricked it. I just ran Windows7 on the velociraptor instead (it worked without re-install, just had to change a few drivers).
 
I don't know how that could help you, just tellin' my experience.

Mother Board ( EVGA X58 132-BL-e758 )                                                       
Drivers ( ????)
Bios ( 77)                                                                                                     
 CPU ( i7 920 d0)
CPU Cooler ( Vigor monsoon LT III)
Memory ( Corsair XMS3 6gb ddr3 1333 )
PSU ( Corsair 750watt)
GPU ( GTX260 )
Drivers ( nvidia 3.3.532.01 )                                                                                                  
Operating System ( Windows 7 64-bit pro)


Frequency Control
CPU Clock Ratio ( 20X )                                                                                         
CPU Host Frequency (Mhz) ( 133 )                                                                      
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) ( auto} )                                                
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )


Memory Feature        
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 1866Mhz / 2:10 )                                                                
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( 2.5 )
tCL Setting ( 9 )
tRCD Setting ( 9 )
tRP Setting ( 9 )
tRAS Setting ( 24 )
tRFC Setting ( 74 )
Command Rate ( 1t )
TREF: auto, 637
TRRD - auto, 5
TFRAW: auto, 20
TRTD: auto, 5


Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( auto, 1.26875)                                                                                                
CPU VTT Voltage ( auto, +0mv)
CPU PLL VCore ( auto, 1.800v)
DIMM Voltage ( 1.500v ) <------ CAN THAT BE IT?!?!?!?
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( auto, 1.100v )
IOH VCore ( auto, 1.100v)
IOH/ICH I/O Voltage ( auto, 1.500v )
ICH VCore ( Auto )
*PWM Frequency ( 800 KHZ )


CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( auto )
OC Recovery ( Disabled )
Turbo Performance ( Disabled ) used with 980X only 

PnP/PCI     PCI Express
Maximum Payload Size ( 128 )
 
Power Management Setup
ACPI Suspend Type ( s1)   
HPET Support ( Enabled )     
HPET Mode ( 64-bit ) 

Which one of these do you have?

TR3X6G1333C9

TR3X6G1333C7

Which one of these do you have?

TR3X6G1333C9

TR3X6G1333C7

 
On the start menu, type "msconfig" in "Search", then go to the boot tab. In there you will see more than one line, select the one that don't say:
"Windows 7 (C:\Windows) : Current OS"
and press "Delete" button and close msconfig. That will fix that.

wow that was really helpful! gosh i wish i knew all these little nicks and tricks.
 
 
i have the

TR3X6G1333C9

i linked it up there on my 1st post.

There are some other things you can do to improve performance:
 
Memory Low Gap ( 1 ) there is no reason to set this higher with your single vid card
 
Maximum Payload Size ( 4096 ) will speed up memory transfers to PCIe a little bit

 
And:
CxE Function ( C5 )
will get you more power savings in sleep mode