EVGA

Hot!Z20 Problem with "Lighting Effect - Preset" , no led light.

Author
freeasabird
New Member
  • Total Posts : 4
  • Reward points : 0
  • Joined: 2021/06/28 02:43:53
  • Status: offline
  • Ribbons : 0
2021/11/08 09:36:35 (permalink)
Hi 
I sadly i have keep my a Z20 Keyboars. All lightning Effect in Preset does not work anymore. I have update Firmware to 1.28 and the unleashRGB to the last one. I have reset the factory settings. Noting helped.
All Keyboard Lights are off. I can config what ever i want in unleashRGB - Lightning Effect - Preset with Static On or other , like red or something else, but all Keycap lights are allways off. 
Unter "unleashRGB - Lightning Effect - Custom " i can set the color of the keycaps and the led light up right.
Any good advice to get the light back under "Lighting Effect - Preset"?
#1

4 Replies Related Threads

    EVGA_James
    EVGA Product Manager
    • Total Posts : 1026
    • Reward points : 0
    • Joined: 2012/12/14 14:54:29
    • Status: offline
    • Ribbons : 3
    Re: Z20 Problem with "Lighting Effect - Preset" , no led light. 2021/11/08 11:07:08 (permalink)
    Check the TOF settings tab under the Leaving. If you have it set to dark and depending on the time set to activate as well as the distance it will turn off the LED. I would suggest setting Leaving to None or increasing the time slider and distance slider. Also make sure not to leave Unleash on the TOF tab when you close or minimize. Switch it over to any one of the other tabs before closing and or minimizing Unleash
     

    post edited by EVGA_James - 2021/11/08 13:20:29


    #2
    freeasabird
    New Member
    • Total Posts : 4
    • Reward points : 0
    • Joined: 2021/06/28 02:43:53
    • Status: offline
    • Ribbons : 0
    Re: Z20 Problem with "Lighting Effect - Preset" , no led light. 2021/11/09 03:35:07 (permalink)
    Hello
     
     
    History . The keyboard works with the setting 6 month. Then suddenly yesterday the keyboard light went off. I sat in front of the keyboard the hole time. I  changed the Profile with "FN + 1- 9" to an other configured Profile, but no keycap light.
     
    Settings now ,i cant remeber the old on because i have reset the settings.
     
    TOF = "on or off",  Time = 0S , None
    Leaving = Time = 10s  , dark
    Distance = 120 cm 
    These setting should do in TOF = on ." after leaving the 120cm area the led lights for 10sec and then they go dark. or?
     
     
    If i have "TOF = 0ff" = i have light. If i change to "TOF = on" and push the "Apply Button", i have immediately no light
     
     
    Can i use TOF only in the mode "Lighting Effect - Preset" and not in the mode "Lighting Effect - Custom"?
     
     
     
     
     
     
     
     

     
    post edited by freeasabird - 2021/11/09 06:20:33
    #3
    EVGA_James
    EVGA Product Manager
    • Total Posts : 1026
    • Reward points : 0
    • Joined: 2012/12/14 14:54:29
    • Status: offline
    • Ribbons : 3
    Re: Z20 Problem with "Lighting Effect - Preset" , no led light. 2021/11/09 09:57:17 (permalink)
    If you don't plan on using the TOF sensor and features you can set it of off. After you set it to off make sure to click apply after any changes you make. Then switch over to the lighting tab to adjust the LEDs and click apply again. 


    #4
    dagamer2020
    New Member
    • Total Posts : 18
    • Reward points : 0
    • Joined: 2008/05/28 22:30:32
    • Status: offline
    • Ribbons : 0
    Re: Z20 Problem with "Lighting Effect - Preset" , no led light. 2024/02/25 17:09:44 (permalink)
    i had a similar problem, i was able to fix my RGB lights to show again by using the FN+ 1-0 keys.  example: key + 1  or FN+2 or "FN and 3" or "FN and 4"... in other words holding down the FN key when then pushing a number key on the top of the keyboard (not the ones on the side).
    #5
    Jump to:
  • Back to Mobile