EVGA

Still Trying! Help 4.0Ghz and higher!

Page: 12 > Showing page 1 of 2
Author
badass1982
iCX Member
  • Total Posts : 304
  • Reward points : 0
  • Joined: 2009/09/26 05:25:10
  • Location: CT, USA
  • Status: offline
  • Ribbons : 0
2011/07/01 11:02:12 (permalink)
Here is my current setup, please no bashing me I'm pretty new to this!
 
                My System Template



    Components   

Mother Board (EVGA x58 Classified E760)
Drivers (Mobo Drivers 9.1.2.1008)
Bios (EVGA version 82)
CPU (Intel Core I7 970@ 2.9 GHz)
CPU Cooler (Water Cooled with an EK Supreme waterblock for CPU)
Memory (OCZ Gold 6GB Budget RAM Kit PN - OCZ3G2000LV6GK)
PSU (Corsair AX 1200 Modular PSU)
GPU (EVGA Radeon 5970 Black Edition w/EK full coverage water block for 5970)
Drivers (11.6)
Operating System ( Windows 7 64 Ultimate )



    Power Management Settings

ACPI function            [ENABLED]
ACPI suspend type        [S1 (POS)]
xrunvgabios if S3 RESUME AUTO
Soft off by power button    [Instant-Off]
wake up by PCI card        [ENABLED]
xUSB KB wake-up from S3         DISABLED
resume by alarm            [DISABLED]
xdate(of month) alarm        0
xtime(hh:mm:ss) alarm        0 : 0 : 0
HPET support            [ENABLED]
HPET mode             [32-bit mode]
power on function        [DISABLED]
xhot key power on          CTRL- F1
PWRON after PWR-FAIL        [OFF]

    PNP/PCI CONFIGURATIONS

Init display first        [PCI SLOT]
Reset configuration data    [DISABLED]
Resources controlled by        [AUTO(ESCD)]
xIRQ Resources            Press Enter
PCI/VGA Palette snoop        [DISABLED]
INT PIN 1            [AUTO]
INT PIN 2            [AUTO]
INT PIN 3            [AUTO]
INT PIN 4            [AUTO]
INT PIN 5            [AUTO]
INT PIN 6            [AUTO]
INT PIN 7            [AUTO]
INT PIN 8            [AUTO]
Reserved RC for bridge        [DISABLED]


**PCI EXPRESS RELATIVE ITEMS**
Maximum payload size [128]

    Frequency/Voltage Control

Dummy OC            [DISABLED]
Extreme Cooling            [DISABLED]
CPU clock ratio            [22x]
CPU host frequency        [133]
xTarget CPU frequency        2933Mhz (133x22)
xTarget Memory frequency    1067Mhz
MCH strap            [AUTO]
CPU Uncore frequency (Mhz)    [AUTO]
CPU Clock Skew            [0PS]
IOH Clock Skew            [0PS]
Spread Spectrum            [DISABLED]
PCIE Frequency         (Mhz)    [100]
OC Recovery            [DISABLED]
Turbo Performance        [ENABLED]

EVGA VDROOP control        [With VDROOP]
CPU V CORE            [AUTO]            1.07500V
CPU VTT VOLTAGE            [AUTO]            +0mv
CPU PLL VOLTAGE            [AUTO]            1.800V
IOH PLL VCORE            [AUTO]            1.800V
QPI PLL VCORE            [AUTO]            1.100V
DIMM VOLTAGE            [AUTO]            1.500V
DIMM DQ VREF            [+0Mv]            +0mv
IOH VCORE            [AUTO]            1.100V
IOH/ICH I/O VOLTAGE        [AUTO]            1.500V
ICH VCORE            [AUTO]            1.100V
VTT PWM FREQUENCY        [250MHz]        250MHz
CPU PWM FREQUENCY        [800MHZ]        800MHz
CPU IMPEDANCE            [AUTO]            AUTO
QPI SIGNAL COMPENSATION        [AUTO]            AUTO

    Memory Feature
Memory SPD            [STANDARD]
Memory control setting        [ENABLED]
Memory Frequency        [AUTO]
xTarget memory frequency        1067Mhz
Channel Interleave Setting    [6 way]
Rank interleave setting        [4 way]
Memory low gap            [AUTO]

Parameters                Setting                Current


tCL                    AUTO                7
tRCD                    AUTO                7
tRD                    AUTO                7
tRAS                    AUTO                18
tRFC                    AUTO                59
tREF                    AUTO                509
Command Rate                AUTO                1T
tRRD                    AUTO                4
tRAW                    AUTO                20
tRTP                    AUTO                4
tWR                    AUTO                8
CH1 Round Trip Latency            AUTO                44
CH2 Round Trip Latency            AUTO                46
CH3 Round Trip Latency            AUTO                46
Back to back CAS delay            AUTO                0
tddWrTRd Setting            AUTO                6
tdrWrTRd Setting            AUTO                6
tsrWrTRd Setting            AUTO                14
tddRdTWr Setting            AUTO                9
tdrRdTWr Setting            AUTO                9
tsrRdTWr Setting            AUTO                9
tddRdTRd Setting            AUTO                7
tdrRdTRd Setting            AUTO                6
tsrRdTRd Setting            AUTO                4
tddWrTWr Setting            AUTO                7
tdrWrTWr Setting            AUTO                7
tsrWrTWr Setting            AUTO                4
tRL                    [+0]
tWL                    [+0]


    CPU Feature

Intel Speedstep            [ENABLED]
XTurbo Mode Function        DISABLED
CxE Function            [DISABLED]
Execute Disable Bit        [ENABLED]
virtualization Technology    [DISABLED]


xxxxxLogical Processor Settingxxxxx
Intel HT Technology        [ENABLED]
Active Processor Cores        [ALL]

xxxxxQPI Controller Settingsxxxxx
QPI Control Settings        [ENABLED]
QPI Link Fast Mode        [ENABLED]
QPI Frequency Selection        [AUTO]  
 
 
#1

47 Replies Related Threads

    mistermister
    CLASSIFIED ULTRA Member
    • Total Posts : 5306
    • Reward points : 0
    • Joined: 2008/03/29 02:38:09
    • Location: San Diego
    • Status: offline
    • Ribbons : 13
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/01 11:40:47 (permalink)
    Im at work, and I am not familiar with your specific i7, however I will take a stab.
     
    Try an odd number multiplier like x21, make sure the memory is clocked at factory specs (including voltage), and turn off the VDroop function. Also, VTT should be ~+175 to +200 mv.


    AMD 3700x / X-570 Aorus Ultra / RTX-3090 FTW3
    #2
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/01 11:49:55 (permalink)
    Thanks will try that and let you know!


    #3
    KMoore4318
    Pistoj Doulos Unum Pluribus
    • Total Posts : 13863
    • Reward points : 0
    • Joined: 2008/12/04 04:20:57
    • Location: Atlanta, Ga
    • Status: offline
    • Ribbons : 238
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/01 13:13:27 (permalink)
     Frequency/Voltage Control

    Dummy OC [DISABLED]
    Extreme Cooling [DISABLED]
    CPU clock ratio [22x]
    CPU host frequency [133]  < Start working this # up until  you BSOD in 5 clock increments until you reach 160 and then 2 clock increments above that test in between for stability and temp. as this # goes up so does your CPU speed and memory speed.
    rxTarget CPU frequency 2933Mhz (133x22)
    xTarget Memory frequency 1067Mhz ( if you set your memory to 2:10 and unacore to 20X) you will hit 1600 memory speed at 160 clocks and 2000 speed at 200 clocks ) ( NOT ALL CPU"S WILL BE ABLE TO HIT 2000)
    MCH Strap [AUTO]
    CPU Uncore frequency (Mhz) [AUTO]  < this must be twice the last # in your memory divider, so for 2:8 this would be 16X. for 2:10 20X and 2:12, 24 X
    CPU Clock Skew [0PS]
    IOH Clock Skew [0PS]
    Spread Spectrum [DISABLED]
    PCIE Frequency (Mhz) [100]
    OC Recovery [DISABLED]
    Turbo Performance [ENABLED] < ALWAYS LEAVE THIS OFF, it's a 980 feature ( will lock your memory at 2:8 and cause BSOD's )  

    EVGA VDROOP control [With VDROOP] < you need about .5 volts more for with Vdroop than you need without. W/O with sets vcore setting as MIN and allows it to go up as needed, with sets Vcore as MAX and allows to drop as necessary )  
    CPU V CORE [AUTO] 1.07500V
    CPU VTT VOLTAGE [AUTO] +0mv
    CPU PLL VOLTAGE [AUTO] 1.800V
    IOH PLL VCORE [AUTO] 1.800V
    QPI PLL VCORE [AUTO] 1.100V
    DIMM VOLTAGE [AUTO] 1.500V < you will need 1.65 as you approach 1600 memory speed and above
    DIMM DQ VREF [+0Mv] +0mv
    IOH VCORE [AUTO] 1.100V
    IOH/ICH I/O VOLTAGE [AUTO] 1.500V
    ICH VCORE [AUTO] 1.100V
    VTT PWM FREQUENCY [250MHz] 250MHz
    CPU PWM FREQUENCY [800MHZ] 800MHz
    CPU IMPEDANCE [AUTO] AUTO
    QPI SIGNAL COMPENSATION [AUTO] AUTO

    Memory Feature
    Memory SPD [STANDARD]
    Memory control setting [ENABLED]
    Memory Frequency [AUTO]
    xTarget memory frequency 1067Mhz
    Channel Interleave Setting [6 way]
    Rank interleave setting [4 way]
    Memory low gap [AUTO]

    Parameters Setting Current
    tCL AUTO 7 ( Set ALL memory timing to specs on the memory for the speed your running it at, should be on the box or the memory itself. ) You can use CPU-z the SPD tab to see various JEDEC settings
    tRCD AUTO 7
    tRD AUTO 7
    tRAS AUTO 18
    tRFC AUTO 59
    tREF AUTO 509
    Command Rate AUTO 1T  < 1T for 6G 2T for 12G
    tRRD AUTO 4
    tRAW AUTO 20
    tRTP AUTO 4
    tWR AUTO 8
    CH1 Round Trip Latency AUTO 44
    CH2 Round Trip Latency AUTO 46
    CH3 Round Trip Latency AUTO 46
    Back to back CAS delay AUTO 0
    tddWrTRd Setting AUTO 6
    tdrWrTRd Setting AUTO 6
    tsrWrTRd Setting AUTO 14
    tddRdTWr Setting AUTO 9
    tdrRdTWr Setting AUTO 9
    tsrRdTWr Setting AUTO 9
    tddRdTRd Setting AUTO 7
    tdrRdTRd Setting AUTO 6
    tsrRdTRd Setting AUTO 4
    tddWrTWr Setting AUTO 7
    tdrWrTWr Setting AUTO 7
    tsrWrTWr Setting AUTO 4
    tRL [+0]
    tWL [+0]


    CPU Feature

    Intel Speedstep [ENABLED] < turn off, this allows downclocking to conserve power.
    XTurbo Mode Function DISABLED < This is the one you want on for Turbo ( NOT TURBO PERFORMANCE )
    CxE Function [DISABLED]
    Execute Disable Bit [ENABLED]
    virtualization Technology [DISABLED]


    xxxxxLogical Processor Settingxxxxx
    Intel HT Technology [ENABLED]
    Active Processor Cores [ALL]

    xxxxxQPI Controller Settingsxxxxx
    QPI Control Settings [ENABLED]
    QPI Link Fast Mode [ENABLED]
    QPI Frequency Selection [AUTO]
    You should break 4.0 around 175 clocks. with a 2:10 tiye memory would be just shy of 1750 and show about 875 on E-leet. expect to be just over 1.32 -1.35 vcore there (??? Guess .)   
    Increase Vcore if you see this BSOD.




    Increase VCORE or CPU VTT if you see this BSOD (you must test by bumping each voltage watching for a change to see which one is needing an increase).

     



    There is a lot of other good information at:
     How to Overclock the I7 (Ported): http://forums.evga.com/fb.ashx?m=7528
    post edited by KMoore4318 - 2011/07/01 13:47:38

      
    Just clink Link to Register >  My Affiliate Code:VTJPDC4OMB 
    1)965 V-8  E761(77)
    2)980X AX1200 E760(77) 980 ti
    3) E770 (77)2(590) SLI AX1200 
    4) X299 FTW K, 9980XE 2 2080 supers on AX1200
    #4
    mistermister
    CLASSIFIED ULTRA Member
    • Total Posts : 5306
    • Reward points : 0
    • Joined: 2008/03/29 02:38:09
    • Location: San Diego
    • Status: offline
    • Ribbons : 13
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/01 19:40:25 (permalink)
    ^^this^^

    AMD 3700x / X-570 Aorus Ultra / RTX-3090 FTW3
    #5
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/02 08:26:59 (permalink)
    Ok guys I appreciate all the help thus far......
     
    Quick update so far so good using the above settings given to me , however i do have one question.....
    what are the IDEAL sort of temperatures i should be running at if i have my cpu at 3.4Ghz at the mo under full load I'm getting like mid 40's across the board on 5 of my 6 cores, under prime 95 maximum heat test!??
     
    thanks.
    Martin
    #6
    KMoore4318
    Pistoj Doulos Unum Pluribus
    • Total Posts : 13863
    • Reward points : 0
    • Joined: 2008/12/04 04:20:57
    • Location: Atlanta, Ga
    • Status: offline
    • Ribbons : 238
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/02 09:08:43 (permalink)
    Your system will shut itself down ( after a down clock attempt at TJ max ( aprox 100 degrees) Most of the guides recommend no more than 85, in an attempt to insure that 100 is never hit. ( this is the number I have been using folding for two plus years. Honestly cooler is better, less temp means longer life. This guide http://hothardware.com/Articles/Intel-Core-i7-Overclocking--A-HotHardware-HowTo/ recommends 65, under stress test.
    How much risk are you willing to take ?
    Mine

    post edited by KMoore4318 - 2011/07/02 09:12:58

      
    Just clink Link to Register >  My Affiliate Code:VTJPDC4OMB 
    1)965 V-8  E761(77)
    2)980X AX1200 E760(77) 980 ti
    3) E770 (77)2(590) SLI AX1200 
    4) X299 FTW K, 9980XE 2 2080 supers on AX1200
    #7
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/02 13:40:57 (permalink)
    OK I'm now running at a nice 3.9Ghz and will probably leave it at 4Ghz as I'm getting what i assume are acceptable temps at 3.9 of 67 degrees and that's only on a maximum of 3 of my 6 cores, please advise if these temps are dangerous , oh btw that's at full load on Prime 95, also how long should i let prime run before i can assume my clocks are bulletproof stable?
     
    Thx
    Martin
     
    #8
    mistermister
    CLASSIFIED ULTRA Member
    • Total Posts : 5306
    • Reward points : 0
    • Joined: 2008/03/29 02:38:09
    • Location: San Diego
    • Status: offline
    • Ribbons : 13
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/02 17:26:08 (permalink)
    You will want to tun 20 iteration of LinX (with the newest 64 bit binaries) at "maximum memory". If you pass that, then run P95 for ~24 hours.
     
    If no BSOD, and it never gets hotter than you want, then you are good to go. 

    AMD 3700x / X-570 Aorus Ultra / RTX-3090 FTW3
    #9
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/02 18:02:27 (permalink)
    Damn just got to 4 hours or so of prime 95 and my computer restarted but i have no idea if i had a bsod as i had my monitor turned off to conserve energy as i was going to stress test for 24 hours!
     
    suggestions!
    ?????
      OK a small update, so i just updated all my overclocking progs to the latest versions:: LinX, Prime95 64bit version, RealTemp etc, and  ran Linx 64 bit without error for 20 passes, however my last attempt at a 24 hour Prime95 run as i sed before only lasted 8 hours!
     
     
    post edited by badass1982 - 2011/07/02 18:59:25
    #10
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/03 03:54:41 (permalink)
    OK so i ran LinX without issue twice for 20 passes on max memory and it was fine, tried Prime95 overnight and I've yet to see a BSOD although when i woke this morning Prime95 had hung on 51 mins, so far that means running Prime 95 at 4.00GHz all i have had is 1 system hang and 1 auto system restart, any ideas as to what is likely to be causing this??? haven't changed any voltages except the cpu vcore, which is now at!: 1.3500v
     
     
    post edited by badass1982 - 2011/07/03 15:09:40
    #11
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/13 07:06:19 (permalink)
    BUMP!
    #12
    KMoore4318
    Pistoj Doulos Unum Pluribus
    • Total Posts : 13863
    • Reward points : 0
    • Joined: 2008/12/04 04:20:57
    • Location: Atlanta, Ga
    • Status: offline
    • Ribbons : 238
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/13 07:36:55 (permalink)
    You will just have to play with both Vcore and Vtt. Every chip is deferent, No two the same, even each chip, in another board with deferent memory can be deferent, vdroop on or off makes a deference, the internal resistance of your components, strength of your IMC, and to some degree, even what you consider stability to mean. What LinX or prime 95 says is stable, Folding SMP at stanford, may disagree.

      
    Just clink Link to Register >  My Affiliate Code:VTJPDC4OMB 
    1)965 V-8  E761(77)
    2)980X AX1200 E760(77) 980 ti
    3) E770 (77)2(590) SLI AX1200 
    4) X299 FTW K, 9980XE 2 2080 supers on AX1200
    #13
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/26 07:08:12 (permalink)
    Ok so just an update I set my settings accordingly and I can use my computer for most all tasks clocked at 4.12Ghz however I cannot for the life of me get it stable (In terms of bulletproof stable) , EVERY time i run either Prime 95 or Linx for an extended period of time (5 hours of more i get errors, (however i have yet to see a BSOD) and my system rarely hangs if ever, i just get errors reported, Is there a setting i should be checking to try to make it stable??? , will post updated settings later on!

    Thx

    Martin
    #14
    KMoore4318
    Pistoj Doulos Unum Pluribus
    • Total Posts : 13863
    • Reward points : 0
    • Joined: 2008/12/04 04:20:57
    • Location: Atlanta, Ga
    • Status: offline
    • Ribbons : 238
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/26 07:12:51 (permalink)
    usually this means your just a smidgen off Vcore or Vtt, what are you at on these two settings. Im running 1.375 vcore, and 1.425 total Vtt with a +225, ( this is with 12G of 2K memory)

      
    Just clink Link to Register >  My Affiliate Code:VTJPDC4OMB 
    1)965 V-8  E761(77)
    2)980X AX1200 E760(77) 980 ti
    3) E770 (77)2(590) SLI AX1200 
    4) X299 FTW K, 9980XE 2 2080 supers on AX1200
    #15
    konsetsu
    New Member
    • Total Posts : 9
    • Reward points : 0
    • Joined: 2010/04/04 04:46:23
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/26 07:32:29 (permalink)
    Sorry bit of a n00b question but 
    HPET support            [ENABLED] 
    HPET mode             [32-bit mode] 
     
    Shouldnt this be set to 64 bit mode for 64 bit OS? 
     
    Im also testing Linx at the moment and have found that the app might crash but adding a few more V's to the core fix's this as KMoore4318 states.
    However I also have cooling issue's on my NB and VRM area's that are causing crash's. I dont know what temps your's are at however. E-leet tool can inform you tho. 
    post edited by konsetsu - 2011/07/26 07:36:45
    #16
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/26 08:03:40 (permalink)
    OK Kmoore i just checked my settings in my BIOS and my CPU Vtt is listen in BIOS as : +200mv and my CPUVcore: 1.35000v
     
    also the cpu vtt is listed as 1.40000v in EVGA E-Leet tool!
    #17
    KMoore4318
    Pistoj Doulos Unum Pluribus
    • Total Posts : 13863
    • Reward points : 0
    • Joined: 2008/12/04 04:20:57
    • Location: Atlanta, Ga
    • Status: offline
    • Ribbons : 238
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/26 09:58:38 (permalink)
    Set HPET ( High percision event timer) to 64, the applacations that can not utilize the 64 will automaticaly drop to what they can use.

      
    Just clink Link to Register >  My Affiliate Code:VTJPDC4OMB 
    1)965 V-8  E761(77)
    2)980X AX1200 E760(77) 980 ti
    3) E770 (77)2(590) SLI AX1200 
    4) X299 FTW K, 9980XE 2 2080 supers on AX1200
    #18
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/26 11:30:03 (permalink)
    OK here is my updated template , running with these settings i can boot my computer and i don't get a BSOD when running LINX and I'm relatively happy with my temps the only ones that are annoying are the MOSFET temps (VREG's) which are approaching the 80 degree Celsius point. Any idea how i can get this overclock stable now???
     
    Template of Current System:
     
    My System Template



        Components   

    Mother Board (EVGA x58 Classified E760)
    Drivers (Mobo Drivers 9.1.2.1008)
    Bios (EVGA version 82)
    CPU (Intel Core I7 970@ 2.9 GHz)
    CPU Cooler (Water Cooled with an EK Supreme waterblock for CPU)
    Memory (OCZ Gold 6GB Budget RAM Kit PN - OCZ3G2000LV6GK)
    PSU (Corsair AX 1200 Modular PSU)
    GPU (EVGA Radeon 5970 Black Edition w/EK full coverage water block for 5970)
    Drivers (11.6)
    Operating System ( Windows 7 64 Ultimate )



        Power Management Settings

    ACPI function            [ENABLED]
    ACPI suspend type        [S1 (POS)]
    xrunvgabios if S3 RESUME AUTO
    Soft off by power button    [Instant-Off]
    wake up by PCI card        [ENABLED]
    xUSB KB wake-up from S3         DISABLED
    resume by alarm            [DISABLED]
    xdate(of month) alarm        0
    xtime(hh:mm:ss) alarm        0 : 0 : 0
    HPET support            [ENABLED]
    HPET mode             [64-bit mode]
    power on function        [DISABLED]
    xhot key power on          ANYKEY
    PWRON after PWR-FAIL        [OFF]

        PNP/PCI CONFIGURATIONS

    Init display first        [PCI EX]
    Reset configuration data    [DISABLED]
    Resources controlled by        [AUTO(ESCD)]
    xIRQ Resources            Press Enter
    PCI/VGA Palette snoop        [DISABLED]
    INT PIN 1            [AUTO]
    INT PIN 2            [AUTO]
    INT PIN 3            [AUTO]
    INT PIN 4            [AUTO]
    INT PIN 5            [AUTO]
    INT PIN 6            [AUTO]
    INT PIN 7            [AUTO]
    INT PIN 8            [AUTO]
    Reserved RC for bridge        [DISABLED]


    **PCI EXPRESS RELATIVE ITEMS**
    Maximum payload size [128]

        Frequency/Voltage Control

    Dummy OC            [DISABLED]
    Extreme Cooling            [DISABLED]
    CPU clock ratio            [24x]
    CPU host frequency        [188]
    xTarget CPU frequency        4520Mhz (188x24)
    xTarget Memory frequency    1883Mhz
    MCH strap            [AUTO]
    CPU Uncore frequency (Mhz)    [3766Mhz (20 X)]
    CPU Clock Skew            [0PS]
    IOH Clock Skew            [0PS]
    Spread Spectrum            [DISABLED]
    PCIE Frequency         (Mhz)    [100]
    OC Recovery            [DISABLED]
    Turbo Performance        [DISABLED]

    EVGA VDROOP control        [Without VDROOP]
    CPU V CORE            [1.40000V]        1.40000V
    CPU VTT VOLTAGE            [+275mv]            +275mv
    CPU PLL VOLTAGE            [AUTO]            1.800V
    IOH PLL VCORE            [AUTO]            1.800V
    QPI PLL VCORE            [AUTO]            1.100V
    DIMM VOLTAGE            [1.650V]        1.650V
    DIMM DQ VREF            [+0Mv]            +0mv
    IOH VCORE            [AUTO]            1.100V
    IOH/ICH I/O VOLTAGE        [AUTO]            1.500V
    ICH VCORE            [AUTO]            1.100V
    VTT PWM FREQUENCY        [250MHz]        250MHz
    CPU PWM FREQUENCY        [800MHZ]        800MHz
    CPU IMPEDANCE            [AUTO]            AUTO
    QPI SIGNAL COMPENSATION        [AUTO]            AUTO

        Memory Feature
    Memory SPD            [STANDARD]
    Memory control setting        [ENABLED]
    Memory Frequency        [1333Mhz / 2:10]
    xTarget memory frequency        1883Mhz
    Channel Interleave Setting    [6 way]
    Rank interleave setting        [4 way]
    Memory low gap            [AUTO]

    Parameters                Setting                Current


    tCL                    10                10
    tRCD                    10                10
    tRD                    10                10
    tRAS                    30                18
    tRFC                    AUTO                59
    tREF                    AUTO                509
    Command Rate                AUTO                1T
    tRRD                    AUTO                4
    tRAW                    AUTO                20
    tRTP                    AUTO                4
    tWR                    AUTO                8
    CH1 Round Trip Latency            AUTO                44
    CH2 Round Trip Latency            AUTO                46
    CH3 Round Trip Latency            AUTO                46
    Back to back CAS delay            AUTO                0
    tddWrTRd Setting            AUTO                6
    tdrWrTRd Setting            AUTO                6
    tsrWrTRd Setting            AUTO                14
    tddRdTWr Setting            AUTO                9
    tdrRdTWr Setting            AUTO                9
    tsrRdTWr Setting            AUTO                9
    tddRdTRd Setting            AUTO                7
    tdrRdTRd Setting            AUTO                6
    tsrRdTRd Setting            AUTO                4
    tddWrTWr Setting            AUTO                7
    tdrWrTWr Setting            AUTO                7
    tsrWrTWr Setting            AUTO                4
    tRL                    [+0]
    tWL                    [+0]


        CPU Feature

    Intel Speedstep            [DISABLED]
    XTurbo Mode Function        DISABLED
    CxE Function            [AUTO]
    Execute Disable Bit        [ENABLED]
    virtualization Technology    [ENABLED]


    xxxxxLogical Processor Settingxxxxx
    Intel HT Technology        [ENABLED]
    Active Processor Cores        [ALL]

    xxxxxQPI Controller Settingsxxxxx
    QPI Control Settings        [ENABLED]
    QPI Link Fast Mode        [ENABLED]
    QPI Frequency Selection        [AUTO]  
     
    Thanks
    Martin
    #19
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 08:34:49 (permalink)
    OK so just a quick update, I managed to get my OC stable according to LinX over 20 passes at full memory (yet to try Prime95 overnight),
    however I am currently not happy with my temps heres my current settings/temps:
     
    VREG TEMPS : Maxes out at 92D which IMHO is WAY to hot!
    CPU CORES: range from 74D - 89D although only 1 core hit 89D (Still a little to high for me, I'm aiming for late 70's max)
     
    VOLTAGES:
    CPU VTT: 1.52V OR +200MV
    CPU VCORE: 1.141250
     
    CURRENT BCLOCK/MULTIPLIER: 192X23 = 4.400Ghz ISH
     
    Any suggestions on any voltages i should be able to lower slightly whilst remaining stable?
     
    thanks
     
    Martin
    #20
    HalloweenWeed
    CLASSIFIED Member
    • Total Posts : 4792
    • Reward points : 0
    • Joined: 2009/11/13 03:32:55
    • Location: Maine, USA
    • Status: offline
    • Ribbons : 37
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 09:10:13 (permalink)
    Now drop your VTT, it will lower CPU core temp and drastically lower Vreg temp. Go 50 per test. Your present VTT is dangerously high. You may need to add a notch or two of CPU Vcore to compensate. If that don't work try increasing QPI PLL Vcore (and decreasing VTT) instead. 1.3V is a good value for QPI PLL. KMoore has a prob W/recommending adding too much VTT. I have achieved 4.35GHz W/0 added VTT (but that was a 920). I had many BSOD 124's during my OC and they never meant to add VTT unlike popular belief. It is true however, for some ppls, they need to add a lot of VTT. Personally, I would never go over +250 VTT, it is too hard on the CPU.
    post edited by HalloweenWeed - 2011/07/27 09:12:52

    Main (gaming) rig: i7-3930K; Asus Rampage IV Extreme; H100 W/p-p Excaliburs, AS5; MSI 7870 2GD5/OC; Crucial M4 SSD 256GB.
    See my primary ModsRigs: Adam for the rest, and I have a second (wife's) rig Asus Rampage III Extreme & 960: Eve.

       
    Overclocking is useless to me if it is not rock stable.
    #21
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 14:15:36 (permalink)
    So halloweed Finally it appears I'm getting somewhere, the following are the latest settings (and temps) that have finished without errors in 20 runs of LinX on full memory:
     
    CPU VTT @ +100mv
    CPUVCore @ 1.40625
    QPI PLL @ 1.300v
    Multiplier @ 23x
    Bclock @ 192
     
    Question on the Multiplier/Bclock: Does it make any difference whether i have a higher Bclock or a higher Multiplier or does diff combinations just work with different chips.
     
    As for temps well i only had one core on the cpu hit 83D this time 2 others maxed at 80D (still a litte high for my preference but A LOT better)
     
    as for the VREG well It's a whole new ball game the temps drastically dropped and before i nipped out to the store they hadnt gone higher than 77D so I'm going to run again just to verify!
     
    Oh 1 more question i ran Prime95 randomly and it gave me MUCH higher temps across the board (excusing the VREG's) is this because of the way it processes data???
     
    Thanks again
     
    Martin
     
     
    So to update the above, I am currently running Prime95 and the VREG and Core temps are a little higher than when LinX is running however they are not too too bad I'm vurrently looking at :
     
    VREG : 92D (bit higher than I'm happy with)
    CPU cores Max:
    1:80D
    2:81D
    3:69D
    4:73D
    5:87D
    6:82D
     
    Had to stop P95 as i wasnt happy AT ALL with these LOAD temps I'm getting .
    post edited by badass1982 - 2011/07/27 14:57:39
    #22
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 14:59:01 (permalink)
    arrrgggghhhh i don't get it when i test with Linx i get respectable results but as soon as i run P95 it kills my system is there any way I'll be able to get to 4.5Ghz stable???
    #23
    HalloweenWeed
    CLASSIFIED Member
    • Total Posts : 4792
    • Reward points : 0
    • Joined: 2009/11/13 03:32:55
    • Location: Maine, USA
    • Status: offline
    • Ribbons : 37
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 16:15:23 (permalink)
    badass1982

    Question on the Multiplier/Bclock: Does it make any difference whether i have a higher Bclock or a higher Multiplier or does diff combinations just work with different chips.

    It don't really matter exc for your memory. You should do whichever runs your mem at the highest speeds stable. Glad to see you are making positive progress.


    badass1982

    Oh 1 more question i ran Prime95 randomly and it gave me MUCH higher temps across the board (excusing the VREG's) is this because of the way it processes data???

    No that's really odd. Typically, for almost everyone, LinX produces higher load temps across the board.
    I'm afraid it might be due to your OCZ RAM. Most ppl on this forum have not had good luck W/OCZ, it's known not to work well with EVGA OCs.
    But there are some more things to try:
    Raise CPU PLL to 2.0Vcore.
    I see your tRAS and tRFC look very low. This can cause memory instability. Try reading what those values should be in AIDA64 (free 30-day trial period), CPU-Z will also show the tRAS in the "spd" tab - but not tRFC. In AIDA64 you would read these values in "Motherboard" --> "spd" --> "Extreme memory profile" --> 1000MHz. Perhaps I will think of something else later, right now have to eat supper. GL.

    Main (gaming) rig: i7-3930K; Asus Rampage IV Extreme; H100 W/p-p Excaliburs, AS5; MSI 7870 2GD5/OC; Crucial M4 SSD 256GB.
    See my primary ModsRigs: Adam for the rest, and I have a second (wife's) rig Asus Rampage III Extreme & 960: Eve.

       
    Overclocking is useless to me if it is not rock stable.
    #24
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 17:26:05 (permalink)
    using that tool it is trying to tell me that my memory is :
     
    @ 533 MHz    7-7-7-16  (CL-RCD-RP-RAS) / 27-59-4-8-4-4  (RC-RFC-RRD-WR-WTR-RTP)
     
    however it is rated at 2000Mhz not 533Mhz x 2 (as it's ddr) which would equal 1066Mhz which is still way off 2000Mhz, also i cannot see in that program "extreme memory profile" I'm using version 1.80 of that program!
    #25
    HalloweenWeed
    CLASSIFIED Member
    • Total Posts : 4792
    • Reward points : 0
    • Joined: 2009/11/13 03:32:55
    • Location: Maine, USA
    • Status: offline
    • Ribbons : 37
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 18:37:20 (permalink)
    Srry I took so long, was meaning to check more often, but the wife and I just watched "Season of the Witch" - excellent movie.

    You should see something like this:



    only the lower circled area should say 1000MHz. Perhaps you need to scroll down? If not, you may have a counterfeit memory prob. Where did you buy it?
    post edited by HalloweenWeed - 2011/07/27 18:49:07

    Main (gaming) rig: i7-3930K; Asus Rampage IV Extreme; H100 W/p-p Excaliburs, AS5; MSI 7870 2GD5/OC; Crucial M4 SSD 256GB.
    See my primary ModsRigs: Adam for the rest, and I have a second (wife's) rig Asus Rampage III Extreme & 960: Eve.

       
    Overclocking is useless to me if it is not rock stable.
    #26
    HalloweenWeed
    CLASSIFIED Member
    • Total Posts : 4792
    • Reward points : 0
    • Joined: 2009/11/13 03:32:55
    • Location: Maine, USA
    • Status: offline
    • Ribbons : 37
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 18:47:13 (permalink)
    When you run P95, are you running "blend"? If so, and your memory is wonky, that would explain your wonky results W/P95. You see it hits memory harder than LinX, more of a workout for the memory than LinX, I think; and much more of a workout than Memtest86+ gives.
    post edited by HalloweenWeed - 2011/07/27 18:51:23

    Main (gaming) rig: i7-3930K; Asus Rampage IV Extreme; H100 W/p-p Excaliburs, AS5; MSI 7870 2GD5/OC; Crucial M4 SSD 256GB.
    See my primary ModsRigs: Adam for the rest, and I have a second (wife's) rig Asus Rampage III Extreme & 960: Eve.

       
    Overclocking is useless to me if it is not rock stable.
    #27
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 19:10:28 (permalink)
    I was running the test that says Maximum heat the middle selection not blend but Large FFT and Im also aware that my RAM is **** so i just want to make sure my CPU MOBO OC is rock solid bulletproof stable, but every time i try to stress test with large FFT it gives an error/locks up or is wayyyy to hot.
     
    My brain is actually hurting now I'll give it another go tomorrow as I'm determined that i can get this 4.5Ghz overclock bulletproof stable on this machine!
     
    Thanks for all your help!
     
    Martin
    #28
    HalloweenWeed
    CLASSIFIED Member
    • Total Posts : 4792
    • Reward points : 0
    • Joined: 2009/11/13 03:32:55
    • Location: Maine, USA
    • Status: offline
    • Ribbons : 37
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 19:18:36 (permalink)
    But do you find anything under 1000MHz in AIDA64 where I showed you? If not, we need to switch gears about the way you are setting your mem.

    Main (gaming) rig: i7-3930K; Asus Rampage IV Extreme; H100 W/p-p Excaliburs, AS5; MSI 7870 2GD5/OC; Crucial M4 SSD 256GB.
    See my primary ModsRigs: Adam for the rest, and I have a second (wife's) rig Asus Rampage III Extreme & 960: Eve.

       
    Overclocking is useless to me if it is not rock stable.
    #29
    badass1982
    iCX Member
    • Total Posts : 304
    • Reward points : 0
    • Joined: 2009/09/26 05:25:10
    • Location: CT, USA
    • Status: offline
    • Ribbons : 0
    Re:Still Trying! Help 4.0Ghz and higher! 2011/07/27 19:43:25 (permalink)
    No nothing at all it doesn't list the Extreme Memory Profiles at all here is a screenie:
     
    http://imageshack.us/phot...mages/225/aida64w.png/
    (couldn't figure out how to insert pic so included the link instead!) 

    #30
    Page: 12 > Showing page 1 of 2
    Jump to:
  • Back to Mobile