EVGA

Helpful ReplyOverclocking 1070 Ti FTW2

Page: < 12 Showing page 2 of 2
Author
Post
Essentials Only Full Version
shadowviper0
New Member
  • Total Posts : 19
  • Reward points : 0
  • Joined: 2017/12/11 23:43:57
  • Status: offline
  • Ribbons : 0
Re: Overclocking 1070 Ti FTW2 2017/12/13 20:27:20 (permalink)
Alright, Im not sure if it actually has a switch that I saw when I put it in.
#31
The_Limit
New Member
  • Total Posts : 89
  • Reward points : 0
  • Joined: 2012/03/23 10:52:19
  • Location: Monroe, LA
  • Status: offline
  • Ribbons : 1
Re: Overclocking 1070 Ti FTW2 2017/12/14 04:33:48 (permalink)
gtx480rocks
OP; I have this card as well; make sure to switch over to slave bios to unlock 130% power limit. Here is what I have with Afterburner (Precision X doesnt track cpu usage)


I totally forgot about this and just switched to the slave BIOS, but I'm still capping at 120%. Thoughts?


BIOS 86.04.85.01.72 (slave) & 86.04.85.00.72 (master) seem to hit the same target


   


~ "I think I'm drunk enough to perfectly know what good is." ~
#32
The_Limit
New Member
  • Total Posts : 89
  • Reward points : 0
  • Joined: 2012/03/23 10:52:19
  • Location: Monroe, LA
  • Status: offline
  • Ribbons : 1
Re: Overclocking 1070 Ti FTW2 2017/12/14 05:19:06 (permalink)
Nevermind. I fixed the issue with a clean reinstall of Precision XOC. Apparently I still must have had some old config files lying around on the SSD.

   


~ "I think I'm drunk enough to perfectly know what good is." ~
#33
shadowviper0
New Member
  • Total Posts : 19
  • Reward points : 0
  • Joined: 2017/12/11 23:43:57
  • Status: offline
  • Ribbons : 0
Re: Overclocking 1070 Ti FTW2 2017/12/16 06:48:24 (permalink)
I do not see a switch, unless I'm not looking in the right spot.
#34
AHowes
CLASSIFIED ULTRA Member
  • Total Posts : 6502
  • Reward points : 0
  • Joined: 2005/09/20 15:38:10
  • Location: Macomb MI
  • Status: offline
  • Ribbons : 27
Re: Overclocking 1070 Ti FTW2 2017/12/16 06:52:58 (permalink)
Usually its to the left of the power connectors on the edge.. its tiny.

Make sure to power off the pc before hand. Drain power from the pc by pulling the psu main plug and hold the power button in for 20-30 secs. Then flip the switch. Then power back on.

Sometimes you msh need to reinstall pxoc afterwards to see the difference.

Intel i9 9900K @ 5.2Ghz Single HUGE Custom Water Loop.
Asus Z390 ROG Extreme XI MB
G.Skill Trident Z 32GB (4x8GB) 4266MHz DDR4 
EVGA 2080ti K|NGP|N w/ Hydro Copper block.  
34" Dell Alienware AW3418DW 1440 Ultra Wide GSync Monitor
Thermaltake Core P7 Modded w/ 2x EK Dual D5 pump top,2 x EK XE 480 2X 360 rads.1 Corsair 520 Rad.
#35
shadowviper0
New Member
  • Total Posts : 19
  • Reward points : 0
  • Joined: 2017/12/11 23:43:57
  • Status: offline
  • Ribbons : 0
Re: Overclocking 1070 Ti FTW2 2017/12/16 06:58:16 (permalink)
Alright, what does switching over to slave do? I haven't really ever messed with graphics cards that much, so this is all completely new to me.
#36
AHowes
CLASSIFIED ULTRA Member
  • Total Posts : 6502
  • Reward points : 0
  • Joined: 2005/09/20 15:38:10
  • Location: Macomb MI
  • Status: offline
  • Ribbons : 27
Re: Overclocking 1070 Ti FTW2 2017/12/16 07:08:39 (permalink)
shadowviper0
Alright, what does switching over to slave do? I haven't really ever messed with graphics cards that much, so this is all completely new to me.


Should raise the power limit on the card and make the fans more agressive. Though you can adjust the fan curve either way.. so really more power potential for higher sustained overclocks.

Intel i9 9900K @ 5.2Ghz Single HUGE Custom Water Loop.
Asus Z390 ROG Extreme XI MB
G.Skill Trident Z 32GB (4x8GB) 4266MHz DDR4 
EVGA 2080ti K|NGP|N w/ Hydro Copper block.  
34" Dell Alienware AW3418DW 1440 Ultra Wide GSync Monitor
Thermaltake Core P7 Modded w/ 2x EK Dual D5 pump top,2 x EK XE 480 2X 360 rads.1 Corsair 520 Rad.
#37
shadowviper0
New Member
  • Total Posts : 19
  • Reward points : 0
  • Joined: 2017/12/11 23:43:57
  • Status: offline
  • Ribbons : 0
Re: Overclocking 1070 Ti FTW2 2017/12/16 07:10:38 (permalink)
Alright, I will work on doing that today then. Thanks
#38
Page: < 12 Showing page 2 of 2
Jump to:
  • Back to Mobile