spit051261
SSC Member
- Total Posts : 930
- Reward points : 0
- Joined: 2019/12/26 16:32:33
- Location: Australia
- Status: offline
- Ribbons : 4
Hi all
Are there any guides / information regarding setting these up.
I thought they were just plug them in and that was that.
Dont want another one going bad .
Gaming Rig - Lian Li Dynamic XL, MSI Z490 Godlike, i9 10900k (SP 88) delidded with Rockit IHS, G-Skill 4266 RAM 2X8 , MSI Z Trio 2080ti, Aorus RGB 360 AIO, EVO 2Tb 970 Plus Nvme,1600watt P2, Acer Predator X27 Monitor, K95 Platinum, G502,G560, ST100 RGB, Void RGB Elite.OC Rig - Lian Li T70, Apex XII , i9 10900k (SP 93) delidded with direct die cooling, G-Skill 4000 2X8 Cl15-16-16 RAM , Evga KPE 2080ti, 2 x 1 Tb Evo 970 Plus Nvme, Evga 1600watt P2, EXC 800 Chiller.
|
Doomed83
Superclocked Member
- Total Posts : 139
- Reward points : 0
- Joined: 2018/02/01 09:06:36
- Status: offline
- Ribbons : 3
Re: kingpin inferno
2020/10/04 17:56:55
(permalink)
Are you using LN2? I personally don't even bother plugging mine in until I'm at -100C pot temperature because above that I don't find it necessary.
|
spit051261
SSC Member
- Total Posts : 930
- Reward points : 0
- Joined: 2019/12/26 16:32:33
- Location: Australia
- Status: offline
- Ribbons : 4
Re: kingpin inferno
2020/10/05 17:13:20
(permalink)
Gaming Rig - Lian Li Dynamic XL, MSI Z490 Godlike, i9 10900k (SP 88) delidded with Rockit IHS, G-Skill 4266 RAM 2X8 , MSI Z Trio 2080ti, Aorus RGB 360 AIO, EVO 2Tb 970 Plus Nvme,1600watt P2, Acer Predator X27 Monitor, K95 Platinum, G502,G560, ST100 RGB, Void RGB Elite.OC Rig - Lian Li T70, Apex XII , i9 10900k (SP 93) delidded with direct die cooling, G-Skill 4000 2X8 Cl15-16-16 RAM , Evga KPE 2080ti, 2 x 1 Tb Evo 970 Plus Nvme, Evga 1600watt P2, EXC 800 Chiller.
|
Doomed83
Superclocked Member
- Total Posts : 139
- Reward points : 0
- Joined: 2018/02/01 09:06:36
- Status: offline
- Ribbons : 3
Re: kingpin inferno
2020/10/05 18:03:32
(permalink)
So my personal experience is that the inferno just doesn't have enough of a benefit on DICE, but your case may vary. Do not plug in the heater until the pot/cpu/mobo is cold, as I said in my previous post I do not bother turning it on until I hit -100C pot temperature. I find that the included thermal pad that is the same shape as the heater sticks a bit too well once you remove the included plastic covering, so a tip I got from another over clocker was to use plastic wrap on both sides of the thermal pad. Once you have the thermal pad on the heater you will need to actually jab the mounting rods through the thermal pad to screw them into the heater. Then I lower the motherboard onto the rods and mount my CPU pot. Imgur link below so you can see how I setup. (start at the bottom) https://imgur.com/a/APEyPpw
|
jab383
New Member
- Total Posts : 36
- Reward points : 0
- Joined: 2015/02/21 14:06:43
- Status: offline
- Ribbons : 1
Re: kingpin inferno
2020/10/24 10:08:12
(permalink)
I do use the Inferno with DICE and it works to limit condensation in and around the socket. I plug it in while temperature is dropping, usually around 0C and unplug at about that point while warming after the session.
|
spit051261
SSC Member
- Total Posts : 930
- Reward points : 0
- Joined: 2019/12/26 16:32:33
- Location: Australia
- Status: offline
- Ribbons : 4
Re: kingpin inferno
2020/10/25 14:39:09
(permalink)
Gaming Rig - Lian Li Dynamic XL, MSI Z490 Godlike, i9 10900k (SP 88) delidded with Rockit IHS, G-Skill 4266 RAM 2X8 , MSI Z Trio 2080ti, Aorus RGB 360 AIO, EVO 2Tb 970 Plus Nvme,1600watt P2, Acer Predator X27 Monitor, K95 Platinum, G502,G560, ST100 RGB, Void RGB Elite.OC Rig - Lian Li T70, Apex XII , i9 10900k (SP 93) delidded with direct die cooling, G-Skill 4000 2X8 Cl15-16-16 RAM , Evga KPE 2080ti, 2 x 1 Tb Evo 970 Plus Nvme, Evga 1600watt P2, EXC 800 Chiller.
|