Each Task fails as soon as they start.
Returning to Driver 373.06 Corrects any issues and Folding will start back up normally.
 
*********************** Log Started 2016-10-23T14:22:50Z ***********************
14:23:18:WU02:FS02:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:23:20:WU03:FS03:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:23:22:WARNING:WU02:FS02:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
14:23:23:WARNING:WU03:FS03:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
14:23:24:WU01:FS01:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:23:28:WARNING:WU01:FS01:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
14:23:31:WU04:FS02:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:23:34:WARNING:WU04:FS02:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
14:23:39:WU01:FS01:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:23:42:WU00:FS00:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:23:42:WARNING:WU01:FS01:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
14:23:45:WARNING:WU00:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
14:24:08:WU04:FS01:0x21:ERROR:exception: Error downloading array interactionCount: clEnqueueReadBuffer (-5)
14:24:09:WU04:FS01:0x21:WARNING:Console control signal 1 on PID 4852
14:24:10:WU01:FS00:0x18:WARNING:Console control signal 1 on PID 6716
14:24:10:WARNING:WU02:FS03:FahCore returned an unknown error code which probably indicates that it crashed
14:24:10:WU01:FS00:0x18:ERROR:103: Lost client lifeline
14:24:10:WARNING:WU02:FS03:FahCore returned: UNKNOWN_ENUM (-1073741510 = 0xc000013a)
14:24:10:WARNING:WU03:FS02:FahCore returned an unknown error code which probably indicates that it crashed
14:24:10:WARNING:WU03:FS02:FahCore returned: UNKNOWN_ENUM (-1073741510 = 0xc000013a)
 
 
If you allow the Client to run it will fail all task and download another one and will not stop or it will Hard Lock Your Computer.
This is on Base Clocks No Tools to set Overclocking or Fan Speeds.

kmarch
If you go into windows event viewer it shows that the driver has crashed to.

Yes it is the NVIDIA Driver and DX Crashed on 193

kmarch
You would think that nvidia would fully test these things before releasing them.

You would think, but Folding is Not Gaming!

MrEnigma
I updated last night, but haven't noticed any change in points since a little after 1 this morning, so I'm wondering whether I'm going to need to rollback when I get home later.....

Are you running Windows 10 or 7/8?
No Folding Tasks would run on my Windows 10 Rig. That is why I posted Not To Use This 375.63 WHQL Driver.
Because they failed on my Win10 Rig I see not point in thanking the time on my Win7/8 Rigs.

MrEnigma
Windows 10......going to check it out when i get home and roll back to 373.06 most likely

 
If you are Folding ok on Driver 375.63 then it looks like you are fine.
MrEnigma27 Active 10.23, 6am last completed Task.

Thanks for that update drougnor,
I dare not post on their site that their is any problem no mater what it might be.

MrEnigma
Got home and checked FAHControl and I saw 'Failed' as the status of my work unit.  Closed it out, rebooted and started it back up and it started to download a work unit, but after a few seconds, would stop (and this is with the folding power on 'medium' - appears that each task would fail as soon as it tried to start).  Rather than check the logs or anything, I rolled back to the previous driver and as of right now, things seems to be back to normal.

You may want to update your Post Above: http://forums.evga.com/FindPost/2568003

I was able to complete one work unit after clean install of 375.63 but I noticed lower than normal power%, GPU usage and thermals. When the 2nd WU began the GPU again would not clock properly and the WU would not start. Then the driver crashed and my monitor started flickering.

EllBrad
I was able to complete one work unit after clean install of 375.63 but I noticed lower than normal power%, GPU usage and thermals. When the 2nd WU began the GPU again would not clock properly and the WU would not start. Then the driver crashed and my monitor started flickering.

EllBrad you are lucky my computer hard locked and I had to press the reset button.
Thank you for Joining the Team this month and remember the TZC next week.
Did you setup your Passkey for the Bonus Points? 

EllBrad

bcavnaugh

EllBrad
I was able to complete one work unit after clean install of 375.63 but I noticed lower than normal power%, GPU usage and thermals. When the 2nd WU began the GPU again would not clock properly and the WU would not start. Then the driver crashed and my monitor started flickering.

EllBrad you are lucky my computer hard locked and I had to press the reset button.
Thank you for Joining the Team this month and remember the TZC next week.
Did you setup your Passkey for the Bonus Points? 

Yes I did yesterday I hope I did it right. How do I tell if I am receiving bonus points? And what is TZC

Have successfully returned at least 10 bonus-eligible WUs, then you will start to see Bonus Points.
Looking this up now!~  http://folding.stanford.edu/home/faq/faq-points#ntoc6
https://folding.stanford.edu/home/faq/faq-passkey/
 

bcavnaugh
Thanks for that update drougnor,
I dare not post on their site that their is any problem no mater what it might be.

Know how that feels Bruce has used his voodoo on me in the past.

My guess is that they are still working on it, unless they fixed something by mistake without meaning to... which would be odd.

Yep
Still no good 

Opolis
Thanks for the investigation work guys.  I game on my main rig a lot and usually update my driver regularly.
Gonna stick it out on 373.06 for the TZC.  Works fine on win10.

Same here. Going to remember to check back here first before i bother updating again