i was about to ask the question, my 970 is not listed but the connector looks good lol

Vlada011
Is it possible to turn these connectors upside down.
Because on my GPU locker is on top.  But still I have problem fan connector. I could remove him because GPU is on water but I would like to stay connected.
 
 

 
 
If not I need to bend VGA Cable on side because it's only 3.5cm to side panel. 
GPU barely fit, but he fit 1cm is from glass to widest part of graphic card. 
 
 
 
 

Update: NO, they are Not reversible.  You Would reverse the Ground & Power - So, they are Made to Only install 1 way  

[The locking clip on the removable adapter would stop you from accidentally reversing those parts]



 
I'm not sure - the documents do not actually say they do ---> I'll check the one I have on the shelf & report back
 
https://www.evga.com/supp...s/PowerLink_Manual.pdf
 
https://www.evga.com/products/pdf/600-PL-2816-LR_spec_sheet_v2.pdf
 
 

Nice! Too bad this tech is slowly dying

Nice

Thanks 

Confirmed that an EVGA PowerLink will fit the EVGA RTX 3060 XC (12G-P5-3655-KR, 12G-P5-3657-KR).  Guessing it will also fit the similar RTX 3060Ti XC (08G-P5-3663-KR).
 
Also confirm (no pic yet) that it will NOT fit the RTX 3070 XC3 (08G-P5-3755-KR).  Presumably this means that it won't fit the nearly identical RTX 3070 XC3's (08G-P5-3751-KR, 08G-P5-3753-KR) and RTX 3060Ti FTW3's (08G-P5-3665-KR, 08G-P5-3667-KR).  RTX 3080 and 3090 XC3's look similar to the 3070 design, but no idea if the fitment is also an issue.  No samples to test...
 
 

looks like a solution to a problem they can fix lol

Armons account
looks like a solution to a problem they can fix lol

It could be done with a new product I guess. It does clean up the cables a bit but I wonder on a 3090 about the room since it could be blocking airflow for such a wide card.

Dude that looks so nice! 

Despite being on the compatibility list the PowerLink is NOT compatible with the 2080 Ti XC Hydro Copper...... 

Under compatibility on the EVGA PowerLink product page.

It is listed as an 11G-P4-2389-BR.

(Got it as a refurb from EVGA so mine actually ends with RX.)

charlesborner

CrayolaTheTitan
Despite being on the compatibility list the PowerLink is NOT compatible with the 2080 Ti XC Hydro Copper...... 

Where's the compatibility list you're finding that on?

https://www.evga.com/support/faq/FAQdetails.aspx?faqid=59659

Your card is 11G-P4-2389-KR, which is NOT on that list.

It would be nice if they could update this list for 3000 series.  Also confirming it works on the 3060 12GB(12G-P5-3657-KR) but definitely not the 3070 TI FTW3  (08G-P5-3797-KL). 

Governator
I like the concept but after reading many posts, the construction just seems a bit on the cheap side and also many complaints of fitment, since what they needed to do is build 2 versions, one for Type-A (clips on bottom) and Type-B (clips on top), surprised this never came up during development. I hope they reconsider one for the 30 series and clean up the development some.

EVGA only has clips facing one way, and EVGA created a piece of hardware for their own products, so why would they make it compatible to other companies? That should be on the other companies to make their own.