So I decided to get some more memory and see what I could do.
 
I got 16GB of the Corsair Dominator GT (CMT8GX3M2A2000C9). It's rated to run 9-10-9-27 @ 1000Mhz, 1.65V
 
I put it in a 790i Ultra with a QX9770 running LC
 
I ran the thing overnight on max stress, v2.5 IBT it was fine. Between 46 and 50 GFlops
 
AIDA read is about 10.3 MB/s
 
I'm running the bus at 1600Mhz, at 1800 things are actually quite a bit slower. I'd love any advice on tweaking out some performance, also, please, any places where the voltages seem too high :) I don't know if I can reduce any of them, but the temps seem good
 
Max Temp MCP is about 58C, Max Temp Cores was 68C
 
BIOS Version: P10
**System **
CPU Freq, MHz: 3600 GHZ
FSB Reference Clock, MHz: 1600
CPU Multiplier: [9X]
PCle x16-1 & 16-2, MHz: [100]
PCle x16-3, MHz: [100]
SPPc->MCP Ref Clock, MHz: [200]
nForce SPP --> nForce MCP: [5X]
nForce SPP c-- nForce MCP: [5X]
**Spread Spectrum**
CPU Spread Spectrum: [Disabled]
HT Spread Spectrum: [Auto]
PCle Spread Spectrurn(SPP): [Disabled]
PCle Spread Spectrurn(MCP): [Auto]
SATA Spread Spectrum: [Disabled]
**FSB & Memorv Config**
FSB - Memory Clock Mode: [Linked]
FSB - Memory Ratio: Sync
FSB (QDR), MHz: [1600]
Actual FSB (QDR), MHz: 1600 
x MEM (DDR), MHz: Linked 
Actual MEM (DDR), MHz: 1600
P1: [AUTO]
P2: [AUTO]
**Memory Timing Setting**
Memory Timing Setting: [manual]
tCL (CAS Latency): 8
tRCD: 9
tRP: 8
tRAS: 27
Command Per Clock: [2T]
** Advanced Memory Settings **
tRRD: [1]
tRC: [26]
tWR: [10]
tWTR: [19]
tFAW: [20]
tREF: [Auto] 7.7 
tRFC: 90
**System Voltages**
CPU Core: [1.3875]
CPU FSB: [1.2]
Memory: [1.65]
nForce SPP: [1.45]
nForce MCP: [1.55]
GTLVREF Lane 0: [-35]
GTLVREF Lane 1: [-35]
GTLVREF Lane 2: [-35]
GTLVREF Lane 3: [-35]
**CPU Configuration**
Limit CPUlD Maxval: Disabled
Intel Speedstep: Disabled
xPPM Mode: [Native]
CPU Thermal Control: [Disabled]
C1E Enhanced Halt State: [Enabled]
Execute Disable Bit: [Enabled]
Virtualization Technology: [Disabled]
CPU Core 0: [Enabled]
CPU Core 1: [Enabled]
CPU Core 2: [Enabled]
CPU Core 3: [Enabled]

* Red areas need to be filled out

Thank you sir!
 
i was hoping you'd weigh in, adjusted per the above, seems to be running pretty well so far!
 
The SPP is at 50C when idle and the MCP 57, under load they are +2 or +3.  Everything else is only a few degrees above room temperature, except the GPU, which is at 37C