EVGA

Helpful ReplyInstalled Bykski Water Block on EVGA 3080 FTW3 ULTRA

Page: < 123 > Showing page 2 of 3
Author
Post
Essentials Only Full Version
kikkoman123
New Member
  • Total Posts : 64
  • Reward points : 0
  • Joined: 2020/11/21 11:05:45
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/10 19:11:56 (permalink)
ComputersAre8ad
How thick is the water block from slot down? My Alphacool block is a fatty and I'm trying to see if I can shave down a few mm so better airflow in my SFF case


 does this help? 


i7 10700K OC by AI 39%
Asus z490-H STRIX
Corsair Vengeance RGB 3200 C16
EVGA 3080 FTW ULTRA Bykski WB 
Corsair Hydro X Cooling:
XC7 - XD5 - XR7 P&P - XR5 - 4 x 120mm QL - 3 x 120mm LL - 2 Noctua 
Lian Li ROG Certified O11 XL THICC
Pic - https://imgur.com/qQkJpEB
 
#31
Lord Winchester
Superclocked Member
  • Total Posts : 222
  • Reward points : 0
  • Joined: 2017/12/25 16:49:25
  • Status: offline
  • Ribbons : 3
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/11 00:43:34 (permalink)
kikkoman123
ComputersAre8ad
How thick is the water block from slot down? My Alphacool block is a fatty and I'm trying to see if I can shave down a few mm so better airflow in my SFF case


does this help? 



Oh heck! 
 
I totally forgot, that technical specs are a thing😂.
 
The mounting instructions where so useless, that I ignored everything else from the website😅


#32
micfogas
New Member
  • Total Posts : 52
  • Reward points : 0
  • Joined: 2020/02/18 16:06:52
  • Location: Southern California
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 05:45:46 (permalink) ☄ Helpfulby kikkoman123 2021/03/12 20:05:22
I ordered my Bykski block for the 3080 ftw3 ultra, from a seller on amazon. I talked with him a bit. I paid for expedited and it got to me from china in ... 3 days? Took him a couple days to ship. But I ended up getting my block well before my card, which is actually arriving today.

I didn't go for the backplate, but now I'm kinda thinking I should have. I'm vertical mounting it tho, in my view 51. I got a new PCIe 4.0 16x capable riser ribbon, since the one I've got now is the cheap thermaltake one (not the premium). I've had a new psu all week, to put in. I've been slacking and still haven't. I got sleeved white cables (I have the view 51 Snow) for my 24pin, both eps, and all 3 PCIe.

I'm also tempted to get the addon display module for the Bykski, just because it looks neat. Displays temp I think. Haven't found the back plate for sale by itself but I might talk to that guy from Amazon and see if I can get one.

I've got a lot of work to do today on my system .. 🙂
#33
Lord Winchester
Superclocked Member
  • Total Posts : 222
  • Reward points : 0
  • Joined: 2017/12/25 16:49:25
  • Status: offline
  • Ribbons : 3
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 06:50:44 (permalink)
micfogas
I ordered my Bykski block for the 3080 ftw3 ultra, from a seller on amazon. I talked with him a bit. I paid for expedited and it got to me from china in ... 3 days? Took him a couple days to ship. But I ended up getting my block well before my card, which is actually arriving today.

I didn't go for the backplate, but now I'm kinda thinking I should have. I'm vertical mounting it tho, in my view 51. I got a new PCIe 4.0 16x capable riser ribbon, since the one I've got now is the cheap thermaltake one (not the premium). I've had a new psu all week, to put in. I've been slacking and still haven't. I got sleeved white cables (I have the view 51 Snow) for my 24pin, both eps, and all 3 PCIe.

I'm also tempted to get the addon display module for the Bykski, just because it looks neat. Displays temp I think. Haven't found the back plate for sale by itself but I might talk to that guy from Amazon and see if I can get one.

I've got a lot of work to do today on my system .. 🙂




As far as i know, they always come with Backplate. Are you sure you don´t have one?
 


#34
micfogas
New Member
  • Total Posts : 52
  • Reward points : 0
  • Joined: 2020/02/18 16:06:52
  • Location: Southern California
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 14:21:58 (permalink)
Lord Winchester

As far as i know, they always come with Backplate. Are you sure you don´t have one?
 


100% positive. They had it for sale with and without. I figured since I'm vert mounting, it's not necessary. And it's not. I'm not worried about the temps. my loop should keep it well within comfort levels. But the asthetic. 🙂 I can order the back plate separate. I seem to have an issue with back plates...
#35
rangerscott
iCX Member
  • Total Posts : 348
  • Reward points : 0
  • Joined: 2008/04/27 20:31:40
  • Location: USA
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 14:50:10 (permalink)
Is there anything in the back side of a 3080 that gets hot like that 3090's?

12900k
Z690 Dark
7900 XTX Nitro
32gb Trident z5 @ 6000
Corsair RM1000X psu
 
#36
Lord Winchester
Superclocked Member
  • Total Posts : 222
  • Reward points : 0
  • Joined: 2017/12/25 16:49:25
  • Status: offline
  • Ribbons : 3
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 14:57:07 (permalink)
micfogas
I seem to have an issue with back plates...



Then you´re going to hate this Backplate :-D.


I mean, it´s more or less straight forward, but i mounted and unmounted it about 15times changing Thermal Pad Configurations before i was happy (or maybe fed up) with the Backplate allignment and how the Cooler sits.


Just be very very carefull when removing the stock Aircooler. There is not much room to wiggle and twist, before you collide the aircooler wit some Capacitors.





#37
Lord Winchester
Superclocked Member
  • Total Posts : 222
  • Reward points : 0
  • Joined: 2017/12/25 16:49:25
  • Status: offline
  • Ribbons : 3
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 15:00:16 (permalink)
rangerscott
Is there anything in the back side of a 3080 that gets hot like that 3090's?



Not really. But you can passively take some heat away from behind GPU Die


#38
micfogas
New Member
  • Total Posts : 52
  • Reward points : 0
  • Joined: 2020/02/18 16:06:52
  • Location: Southern California
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 16:22:32 (permalink)
Lord Winchester
micfogas
I seem to have an issue with back plates...



Then you´re going to hate this Backplate :-D.


I mean, it´s more or less straight forward, but i mounted and unmounted it about 15times changing Thermal Pad Configurations before i was happy (or maybe fed up) with the Backplate allignment and how the Cooler sits.


Just be very very carefull when removing the stock Aircooler. There is not much room to wiggle and twist, before you collide the aircooler wit some Capacitors.





My issue is more... Umm.. losing them. 😂 Almost cost me my step up. Thankfully I found it. Ups should be here within the hour. And I haven't even pulled my old PSU out yet. I better get moving on it.
#39
micfogas
New Member
  • Total Posts : 52
  • Reward points : 0
  • Joined: 2020/02/18 16:06:52
  • Location: Southern California
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 16:24:11 (permalink)
How picky is this block with pad thickness/position? I mean obviously they have to line up, but anyone have an issue with the cold plate not making good enough contact with the die?
#40
kikkoman123
New Member
  • Total Posts : 64
  • Reward points : 0
  • Joined: 2020/11/21 11:05:45
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/03/12 20:07:33 (permalink)
micfogas
How picky is this block with pad thickness/position? I mean obviously they have to line up, but anyone have an issue with the cold plate not making good enough contact with the die?



ive read some people in the past had some issues with 2080/1080 blocks. haven’t read anything on the 3080/90 block so far. it’s cnc machined if that matters. 

i7 10700K OC by AI 39%
Asus z490-H STRIX
Corsair Vengeance RGB 3200 C16
EVGA 3080 FTW ULTRA Bykski WB 
Corsair Hydro X Cooling:
XC7 - XD5 - XR7 P&P - XR5 - 4 x 120mm QL - 3 x 120mm LL - 2 Noctua 
Lian Li ROG Certified O11 XL THICC
Pic - https://imgur.com/qQkJpEB
 
#41
critofur
New Member
  • Total Posts : 68
  • Reward points : 0
  • Joined: 2021/02/23 15:00:56
  • Location: Central USA
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/12 09:08:36 (permalink)
Lord Winchester
The Build is done BTW [pic removed]



Very nice, but, one thing would drive me nuts: the angle of your GPU card - how come it's angled like that? 
#42
kikkoman123
New Member
  • Total Posts : 64
  • Reward points : 0
  • Joined: 2020/11/21 11:05:45
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/12 21:52:55 (permalink)
critofur
Lord Winchester
The Build is done BTW [pic removed]



Very nice, but, one thing would drive me nuts: the angle of your GPU card - how come it's angled like that? 


its angled horizontal. do u see something else?

i7 10700K OC by AI 39%
Asus z490-H STRIX
Corsair Vengeance RGB 3200 C16
EVGA 3080 FTW ULTRA Bykski WB 
Corsair Hydro X Cooling:
XC7 - XD5 - XR7 P&P - XR5 - 4 x 120mm QL - 3 x 120mm LL - 2 Noctua 
Lian Li ROG Certified O11 XL THICC
Pic - https://imgur.com/qQkJpEB
 
#43
Rustlinjimmies
New Member
  • Total Posts : 7
  • Reward points : 0
  • Joined: 2020/09/25 19:28:00
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/15 22:09:00 (permalink)
So I ordered a byski block but found someone selling an ek block local never used so I said screw it but then I stuumbled on the thread of the ek blocks bricking the ftw3 cards so now im on the fence if I should just a avoid the ek block now. Any advice would be lovely thank you 
#44
phroze
SSC Member
  • Total Posts : 799
  • Reward points : 0
  • Joined: 2018/09/17 20:09:17
  • Location: WA State
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/16 07:50:04 (permalink)
kikkoman123
critofur
Lord Winchester
The Build is done BTW [pic removed]



Very nice, but, one thing would drive me nuts: the angle of your GPU card - how come it's angled like that? 


its angled horizontal. do u see something else?


I think he is talking about Lord Winchester's. Looks like it is running down hill. I used the EK bracket to avoid that issue.

Case: Lian Li O11 Dynamic XL
Mobo: Asrock X570 Taichi
CPU: Ryzen 5900x
GPU: EVGA RTX 3090 FTW3 Ultra
RAM: Crucial Ballistix OC to 3800 16 18 18 1:1
PSU: EVGA SuperNova G2 1600w
Cooling: Custom hardline loop: optimus blocks, primochill stuff, lian li stuff, HW Labs 60mm radiators, custom stuff
#45
kikkoman123
New Member
  • Total Posts : 64
  • Reward points : 0
  • Joined: 2020/11/21 11:05:45
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/18 01:23:34 (permalink)
Rustlinjimmies
So I ordered a byski block but found someone selling an ek block local never used so I said screw it but then I stuumbled on the thread of the ek blocks bricking the ftw3 cards so now im on the fence if I should just a avoid the ek block now. Any advice would be lovely thank you 


can u post a link to the thread about ek blocks bricking?
 
u cancel yer order for the bykski block?
 
side note: i changed my setup to bottom intake, side exhaust p/p rad and top exhaust rad, rear single intake.
 
 
post edited by kikkoman123 - 2021/04/18 01:34:41

i7 10700K OC by AI 39%
Asus z490-H STRIX
Corsair Vengeance RGB 3200 C16
EVGA 3080 FTW ULTRA Bykski WB 
Corsair Hydro X Cooling:
XC7 - XD5 - XR7 P&P - XR5 - 4 x 120mm QL - 3 x 120mm LL - 2 Noctua 
Lian Li ROG Certified O11 XL THICC
Pic - https://imgur.com/qQkJpEB
 
#46
rrusek
New Member
  • Total Posts : 12
  • Reward points : 0
  • Joined: 2020/10/17 13:18:15
  • Location: CA
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/21 17:58:39 (permalink)
Can you please PM me with guide/breakdown video of putting a Bykski water block on a 3080 FTW3 ULTRA.
 
I would PM you but am new to the forum so I do not have enough posts to be able to pm people.
 
Thanks,
RJR

--
RJR
#47
rrusek
New Member
  • Total Posts : 12
  • Reward points : 0
  • Joined: 2020/10/17 13:18:15
  • Location: CA
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/28 19:56:24 (permalink)
Can anyone confirm that they have or have not used the supplied washer / spacers for the 3080?
 
I have been reading that they are only required for the 3090?
 
Thanks,
RJR

--
RJR
#48
rrusek
New Member
  • Total Posts : 12
  • Reward points : 0
  • Joined: 2020/10/17 13:18:15
  • Location: CA
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/28 19:59:55 (permalink)
Also can the supplied thermal pads be used for the installation?  I have read that you need 1mm pads for the vram and 1.5 for everything else.
 
Thanks,
RJR

--
RJR
#49
rrusek
New Member
  • Total Posts : 12
  • Reward points : 0
  • Joined: 2020/10/17 13:18:15
  • Location: CA
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/28 20:02:01 (permalink)
Can someone specify what temps you are getting for the memory under load?  I am getting 80c, is that normal?
 
Thanks,
RJR

--
RJR
#50
ddog661
Superclocked Member
  • Total Posts : 112
  • Reward points : 0
  • Joined: 2021/04/14 23:11:33
  • Status: offline
  • Ribbons : 0
Flagged as Spam (1)
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/28 20:02:33 (permalink)
Nice!

EVGA Associate Code: S7J93UZF57CEOFM
Elite Program Referral Link: https://www.evga.com/member/elite/?referralid=NHS68RYWQ0PFNE7WHFBB
 
Use the associate code when purchasing an item or use the link when you meet the requirements to become an elite member (if you so desire)
#51
rrusek
New Member
  • Total Posts : 12
  • Reward points : 0
  • Joined: 2020/10/17 13:18:15
  • Location: CA
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/28 20:14:58 (permalink)
Also has anyone stacked pads on the inductors so that they touch the water block?
 
Thanks,
RJR

--
RJR
#52
D3_GX
Superclocked Member
  • Total Posts : 102
  • Reward points : 0
  • Joined: 2021/04/29 18:54:53
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/04/30 19:46:01 (permalink)
Nice but please use temps in Celsius next time.
#53
Dabadger84
CLASSIFIED Member
  • Total Posts : 3426
  • Reward points : 0
  • Joined: 2018/05/11 23:49:52
  • Location: de_Overpass, USA
  • Status: offline
  • Ribbons : 10
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/01 01:38:07 (permalink)
So how are your temps with this thing on standard loads, like say a single run of Port Royal?  I'd love to compare notes now that I have a HydroCopper block on my Kingpin.

ModRigs: https://www.modsrigs.com/detail.aspx?BuildID=42891  
Specs:
5950x @ 4.7GHz 1.3V - Asus Crosshair VIII Hero - eVGA 1200W P2 - 4x8GB G.Skill Trident Z Royal Silver @ 3800 CL14
Gigabyte RTX 4090 Gaming OC w/ Core: 2850MHz @ 1000mV, Mem: +1500MHz - Samsung Odyssey G9 49" Super-Ultrawide 240Hz Monitor
 
#54
kikkoman123
New Member
  • Total Posts : 64
  • Reward points : 0
  • Joined: 2020/11/21 11:05:45
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/02 03:05:41 (permalink)
rrusek
Can you please PM me with guide/breakdown video of putting a Bykski water block on a 3080 FTW3 ULTRA.
 
I would PM you but am new to the forum so I do not have enough posts to be able to pm people.
 
Thanks,
RJR


Its less of a breakdown but more of just a light guide. Bascially follow the gamers nexus breakdown then follow the bykski instructions.
 
rrusek
Can anyone confirm that they have or have not used the supplied washer / spacers for the 3080?
 
I have been reading that they are only required for the 3090?
 
Thanks,
RJR


Do not use the spacers for the 3080.
 
rrusek
Also can the supplied thermal pads be used for the installation?  I have read that you need 1mm pads for the vram and 1.5 for everything else.
 
Thanks,
RJR


Of course they can be used, thats what it comes with. They are 1.7 or 1.8 mm.
 
rrusek
Can someone specify what temps you are getting for the memory under load?  I am getting 80c, is that normal?
 
Thanks,
RJR


80c for a air cooled or water cooled? high for air but WAY too high for water. im getting max 120f (48c) with undervolt with 80F (26C) ambient, and thats on a hot day.
 
D3_GX
Nice but please use temps in Celsius next time.




No. Merica.
 
Dabadger84
So how are your temps with this thing on standard loads, like say a single run of Port Royal?  I'd love to compare notes now that I have a HydroCopper block on my Kingpin.




I dont do synthetic benchmarks. I play games. I will say that in the Shadow of the Tomb Raider bench mark this is the result. Stock AVG FPS - 102, Min 80. OC 2160mhz - 106, Min 84. UnderVolt 1890mhz - 100, Min 73.

i7 10700K OC by AI 39%
Asus z490-H STRIX
Corsair Vengeance RGB 3200 C16
EVGA 3080 FTW ULTRA Bykski WB 
Corsair Hydro X Cooling:
XC7 - XD5 - XR7 P&P - XR5 - 4 x 120mm QL - 3 x 120mm LL - 2 Noctua 
Lian Li ROG Certified O11 XL THICC
Pic - https://imgur.com/qQkJpEB
 
#55
Dabadger84
CLASSIFIED Member
  • Total Posts : 3426
  • Reward points : 0
  • Joined: 2018/05/11 23:49:52
  • Location: de_Overpass, USA
  • Status: offline
  • Ribbons : 10
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/02 03:10:00 (permalink)
kikkoman123
 
 
Dabadger84
So how are your temps with this thing on standard loads, like say a single run of Port Royal?  I'd love to compare notes now that I have a HydroCopper block on my Kingpin.




I dont do synthetic benchmarks. I play games. I will say that in the Shadow of the Tomb Raider bench mark this is the result. Stock AVG FPS - 102, Min 80. OC 2160mhz - 106, Min 84. UnderVolt 1890mhz - 100, Min 73.


 
Temperatures mate, not FPS.  Also Port Royal is a great example of how RTX titles would play on a GPU, which is why it's a standard thing folks run to check out their new hardware or new cooling.

ModRigs: https://www.modsrigs.com/detail.aspx?BuildID=42891  
Specs:
5950x @ 4.7GHz 1.3V - Asus Crosshair VIII Hero - eVGA 1200W P2 - 4x8GB G.Skill Trident Z Royal Silver @ 3800 CL14
Gigabyte RTX 4090 Gaming OC w/ Core: 2850MHz @ 1000mV, Mem: +1500MHz - Samsung Odyssey G9 49" Super-Ultrawide 240Hz Monitor
 
#56
kalebg1
Superclocked Member
  • Total Posts : 117
  • Reward points : 0
  • Joined: 2018/07/24 13:11:45
  • Location: Olympic Peninsula, Wa
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/02 12:29:55 (permalink)
Lord Winchester

 
 
 
This is the MP5WORKS Backplatecooler
 


Watercooled backplate. Seems excessive....Now I want one lol

12G-P5-3967-KR6/3/2021 7:30:26 AM PT No
12G-P5-3958-KR6/3/2021 7:41:25 AM PT YES
10G-P5-3881-KR 9/17/2020 2:20:58 PM PT No
10G-P5-3883-KR 9/17/2020 2:21:40 PM PT No
#57
AMerexican
New Member
  • Total Posts : 100
  • Reward points : 0
  • Joined: 2021/04/29 02:22:24
  • Status: offline
  • Ribbons : 0
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/02 14:44:00 (permalink)
Isn't excessive the whole point of custom loops? :P
#58
Dabadger84
CLASSIFIED Member
  • Total Posts : 3426
  • Reward points : 0
  • Joined: 2018/05/11 23:49:52
  • Location: de_Overpass, USA
  • Status: offline
  • Ribbons : 10
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/02 15:44:35 (permalink)
kalebg1
Lord Winchester

 
 
 
This is the MP5WORKS Backplatecooler
 


Watercooled backplate. Seems excessive....Now I want one lol


If you're going to put a block on the card, the backside just needs a pad upgrade & some heatsinks as I've shown with my memory Temps.

ModRigs: https://www.modsrigs.com/detail.aspx?BuildID=42891  
Specs:
5950x @ 4.7GHz 1.3V - Asus Crosshair VIII Hero - eVGA 1200W P2 - 4x8GB G.Skill Trident Z Royal Silver @ 3800 CL14
Gigabyte RTX 4090 Gaming OC w/ Core: 2850MHz @ 1000mV, Mem: +1500MHz - Samsung Odyssey G9 49" Super-Ultrawide 240Hz Monitor
 
#59
kikkoman123
New Member
  • Total Posts : 64
  • Reward points : 0
  • Joined: 2020/11/21 11:05:45
  • Status: offline
  • Ribbons : 2
Re: Installed Bykski Water Block on EVGA 3080 FTW3 ULTRA 2021/05/03 06:08:00 (permalink)
Dabadger84
kikkoman123
 
 
Dabadger84
So how are your temps with this thing on standard loads, like say a single run of Port Royal?  I'd love to compare notes now that I have a HydroCopper block on my Kingpin.




I dont do synthetic benchmarks. I play games. I will say that in the Shadow of the Tomb Raider bench mark this is the result. Stock AVG FPS - 102, Min 80. OC 2160mhz - 106, Min 84. UnderVolt 1890mhz - 100, Min 73.


 
Temperatures mate, not FPS.  Also Port Royal is a great example of how RTX titles would play on a GPU, which is why it's a standard thing folks run to check out their new hardware or new cooling.




The only thing that really pushes its power level that I play is quake II rtx, 120f max in a hot 80f room

i7 10700K OC by AI 39%
Asus z490-H STRIX
Corsair Vengeance RGB 3200 C16
EVGA 3080 FTW ULTRA Bykski WB 
Corsair Hydro X Cooling:
XC7 - XD5 - XR7 P&P - XR5 - 4 x 120mm QL - 3 x 120mm LL - 2 Noctua 
Lian Li ROG Certified O11 XL THICC
Pic - https://imgur.com/qQkJpEB
 
#60
Page: < 123 > Showing page 2 of 3
Jump to:
  • Back to Mobile