Part List
Stable Overclock
For sale thread for parts I don't need, fans, grommet, MDPC sleeve 
 

 
moar pics

Here are instructions on how to fit a NH-D14 to push air over the rear I/O panel of an e758 mobo
NH-D14 Solution:

1. Remove the VRM HS, two tiny screws on the back of the MB, careful not to tear the long thermal pad
2. Optional: Remove DIMM 0 and 1 Dominator HS if you want to fit the 120mm fan perfectly. If Dom HS remains the 120mm fan will be raised by about 2cm.
3. Install the NH D14, installation manual, with the 120mm fan over the RAM pushing air towards the I/O shield (Be sure to follow your Intel install manual)
4. Tighten all the appropriate screws as per installation manual 
5. Then drop the heatsink back on pressing firmly so the thermal pads stick to the chips 
6. Flip the MB so it is perpendicular to your work surface, be sure to keep a slight hold, left hand, on the NH-D14 from the top of the MB 
7. Screw in the top part of the HS first, not tOo much leave space to pivot the HS, pressing down on it with your left index finger to catch the screw
8. Align the bottom half, by the NB HS, with the screw hole 
9. Reaching over the HS with your left index finger press down on the middle of the HS to catch the screw (at this time i was still holding the NH-D14 with my left pinkY, ring and middle fingers as a precaution)
10. Once you have both screws in, tighten them accordingly and you're all set

 The NH-D14 will be touching the HS but only at the tips of the heatpipes.
**DISCLAIMER** I am not responsible or liable for any damages to your board, heatsink, cpu or any other components. **DISCLAIMER**

Some items came in today, take a look

cant wait see finished article cool !!

Stable OC of 4.2GHz temps peaked at 77*C with 100 runs of IBT


turbo disabled 
VDroop Control Without VDroop 
VCore 1.375v 
VTT +300mV 
PLL Auto 
DIMM 1.65v 
DIMM DQ Vref 0mV 
QPI PLL VCore 1.4v 
IOH VCore 1.4v 
IOH/ICH I/O 1.65v 
ICH VCore 1.25v
PWM Freq 800KHz 

Multiplier 21
Bclock 200 
FSB:RAM 2:8

Nice build. That is one massive air cooler though.

everything came in today except my ven x fans, log updated

I didnt order enough grommet from perf. PCs so the window is going to have to wait until next week

be sure to check out my for sale thread that has fans, sleeves, etc. that wont be needed 

thanks.... i think i need a clipboard manager lol

well updated the log a bit, removed the HDD cage completely because I had to move the 200mm fan up because it was blocking the push pin holes for the front panel

also my akasa fans came in today for the VEN-X, but I can't seem to take the blades off to paint them, they dont have a rubber stopper to access the axel, it's all sealed up except for this tiny 1x2mm hole that i can see the PCB

Very well done Hugh.  I like it a lot!

Build complete for the most part

Corsair dominators have become so expensive since last yr when they were just $150 for 6gb and now $220-$280 depending on CAS. SMH.

692 and 3x monitors FTW!!!!!!!!!!!!! What monitor stand is that, im in dire need

Hugh: Post some more pics (close up shots of the chassis) and maybe I can give you a BR.

rjohnson11

Hugh: Post some more pics (close up shots of the chassis) and maybe I can give you a BR.

 
but.... but... but... check the picasa web album :'(
 
http://picasaweb.google.c...SQ&feat=directlink

Nicce 3 monitors!