If Comodo is uninstalled does the problem still occur? Has the problem only occurred recently? If the problem occurred only recently then I recommend you try and find a system restore point prior to when the troubles began.

Was this a fresh install of Windows 7 or did you upgrade?

I don't think this is a Windows 7 problem. Go to the X58 section and download the X58 template from the sticky section. Fill this out and then post back with it.

Mother Board ( EVGA X58 FTW3 E768 )                                                       
Drivers ( 1025 )
Bios ( 74 )                                                                                                     
 CPU ( 930 ) ( 3002A822 ) (DO)                    
CPU Cooler ( Corsair  H50 )
Memory ( Corsair Dominator 8-8-24-2T)
PSU ( Ultra X3 1000W )
GPU ( GTX260 )
Drivers ( 258.96)                                                                                                  
Operating System ( Windows 7 64 Pro )


Frequency Control
CPU Clock Ratio (  21 ) 
CPU Host Frequency (3770Mhz) (180*21  )                                                                      
MCH Strap (   Auto   )
CPU Uncore Frequency (Mhz) (  Auto  )                                                
CPU Clock Skew (  0ps  )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 ) If using SSDs, Check with your SSD manufacturer before raising above 100. The higher you raise the PCI-e Frequency the more problems you will see. Any problems with NICs or USB return this setting to 100.  


Memory Feature        
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency 1067Mhz / 2:8 )                                                                
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap  (3 )
tCL Setting ( 8 )
tRCD Setting ( 8 )
tRP Setting ( 8 )
tRAS Setting ( 24 )
tRFC Setting ( Auto   74  )
Command Rate ( 2t )
tRL ( +0 )

Voltage Control
EVGA VDroop Control ( With VDroop )
CPU VCore ( Auto )                                                                                                
CPU VTT Voltage ( Auto)
CPU PLL VCore (Auto)
**IOH PLL VCore (  No Option on FTW3 Mobo    ) 
DIMM Voltage (Auto)
DIMM DQ Vref (Auto)
QPI PLL VCore (   Auto)  Raising this will help you lower your VTT
IOH VCore ( Auto ) Set to 1.2 if you are using more then 1 video card 
IOH/ICH I/O Voltage ( Auto )
**BR04 ( NF200) Voltage ( ### ) (only on E-759)
**VTT PWM Frequency (  No option of FTW3 Mobo )
**CPU PWM Frequency ( No option of FTW3 Mobo)
**CPU Impedance ( No option of FTW3 Mobo )
**QPI Signal Compensation ( No option of FTW3 Mobo)
ICH VCore ( Auto )
*PWM Frequency ( 800KHz )


CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Disabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s )
OC Recovery ( Disabled )
Turbo Performance ( Disabled ) used with 980X only 
PnP/PCI Express
Maximum Payload Size (128)
Power Management Setup
ACPI Suspend Type ( S1)
HPET Support ( Enabled)
Hpet Mode ( 64-bit)

When dealing with installation of major programs that integrate themselves into your os and installing an os you really should be running your hardware at stock to make sure things do not go wrong. It can happen might need to do a fresh install of windows with your hardware not overclocked.

donta1979

When dealing with installation of major programs that integrate themselves into your os and installing an os you really should be running your hardware at stock to make sure things do not go wrong. It can happen might need to do a fresh install of windows with your hardware not overclocked.

My system was stock when I installed Win7,  yes i ran memtest no errors were reported
Stock or overclocked I'm having the same problems

donta1979

possilby just a bad install might want to install it one more time, I have had this happen before but it was with vista.

Great something i am not looking forward to. lol

rjohnson11

If you reinstall Windows 7 or do a repair install do so at the default PC settings with no overclocking

i know that