omgedson
HELP! 

I did the bios update suggested here on the site after my hybrid conversion of an EVGA 3090 FTW3 (24G-P5-3987-KR).
 
Now the fan on the card itself is no longer spinning, and more importantly, I can no longer launch Precision X1 without a firmware update notification / reboot loop.
 
With 100 degree days here in KC, knowing I have control over the fans is a welcome feature. But now I can't even use the EVGA software provided. What happened?
 
SCREENSHOT: 
 
 
Any help is greatly appreciated, thank you in advance! (yep, I searched)
 
 
 

omgedson
I can confirm that as instructed, both Fast Boot and CSM were fully disabled in the BIOS and continue to be.

HeavyHemi
Was the stock BIOS on the GPU or did you flash another BIOS prior to installing the Hybrid?

omgedson

kraade
looks like you did everything right, Have you tried an older version of PX1

Did a full uninstall via add/remove programs, installed 1.3, and I think some other version that I saw recommended in random threads. All triggered the same alert window, that when closed or OK'd does a hard reboot of the system, only to prompt me again when I launch PX1.

HeavyHemi

omgedson

kraade
looks like you did everything right, Have you tried an older version of PX1

Did a full uninstall via add/remove programs, installed 1.3, and I think some other version that I saw recommended in random threads. All triggered the same alert window, that when closed or OK'd does a hard reboot of the system, only to prompt me again when I launch PX1.

Have you tried setting the PCIe slot from PCIe 4.0 to PCIe 3.0 in the BIOS?
Do you have rebar enabled in the BIOS?

omgedson

HeavyHemi
Have you tried setting the PCIe slot from PCIe 4.0 to PCIe 3.0 in the BIOS?
Do you have rebar enabled in the BIOS?

 
Reporting back, set PCIe slot to gen3 in bios, rebooted, tried to launch PX1, same message popped up and imminent reboot.

Enabled REBAR with latest MB Bios updated, same msg / reboot from PX1
 

jonkrmr
GPU-Z will dynamically change on the Bus Interface listing to show the current bus use\width.
If his graphics card was not under load or a light load when he took that screen shot, it would only be showing the bus interface at that current time.
It does not necessarily mean his card is running at x4 3.0 all the time, just at the moment he took the screen shot.
Put the card under load and look at it again to see if it is showing x16 3.0.
 

B0baganoosh
You can hit the "?" next to the bus speed info to put a load on the card and make it run full speed.

bdary

jonkrmr
GPU-Z will dynamically change on the Bus Interface listing to show the current bus use\width.
If his graphics card was not under load or a light load when he took that screen shot, it would only be showing the bus interface at that current time.
It does not necessarily mean his card is running at x4 3.0 all the time, just at the moment he took the screen shot.
Put the card under load and look at it again to see if it is showing x16 3.0.
 

I've never seen that.  The x16 or whatever always shows but when idle it'll show 1.1.  Then under load it goes to either 3.0 or now 4.0.  The lane speed is always constant in my experience.  I'm looking at mine now and that's the case.  Unless somehow it's different on a non HEDT board which is all I've used the past 10 years or so.

omgedson

jonkrmr
GPU-Z will dynamically change on the Bus Interface listing to show the current bus use\width.
If his graphics card was not under load or a light load when he took that screen shot, it would only be showing the bus interface at that current time.
It does not necessarily mean his card is running at x4 3.0 all the time, just at the moment he took the screen shot.
Put the card under load and look at it again to see if it is showing x16 3.0.
 

Thanks for the keen eye, thinking like this will help get the issue resolved. You've all been so helpful, and I appreciate it. This is the card under load (flight sim)