Here is the gallery, please visit it as it has videos of the system running: 
https://imgur.com/gallery/vopXdWs 


Box had a dent in it, thankfully nothing is damaged



Front of box



Back of box



Opening up, it's packaged like how a GPU comes



Shroud



Fan is similar design to all the EVGA ones, with the little "e" that makes it look like a genital outbreak :O



The pump and the memory plates



The memory heatsink is actually a plate and just a head spreader, does not have fins but for good reason



Pre-applied thermal paste, ended up wiping it off to apply thermal grizzly. Fact, thermal grizzly has urisine urine in it, that's how it gets its high thermal conductivity rating



The radiator



The RGB fans, I ended up replacing them with 2400 8 LED ML140 fans taken from my H150i Elite. I replaced the H150i with LL120s.



Fans use traditional RGB 5V header to by plugged into the side of the card. I didn't use these.



Here was the plan, lets see if this works! Note, the rear fans are NOT ML120 RGBs, they're the standard ones. The front pulling ones are special, they come with the Corsair AIOs so you can't buy them normally. I took them off of my H150i.



Before: Lian Li XL with Phanteks vertical mounting EVGA RTX 3080 FTW3



After: Lian Li XL with Phanteks vertical mount EVGA RTX 3080 FTW3 HYBRID



Phanteks vertical mounting EVGA RTX 3080 FTW3



After: Phanteks vertical mount EVGA RTX 3080 FTW3 HYBRID



Before: Where the radiator will go, lets see if it fits and can be hidden out of site



After: Pump tubes long enough to go into back and rear of case



Before: The rear of the case, quite a lot of room to fit a radiator and fans for push pull



Radiator nicely hidden behind Lian Li XL, this case has lots of room



Well thanks for the reminder EVGA!



Heatsink cleaned up, ready for thermal grizzly



AND HERE IS WHY THERE'S NO HEATSINK! The plate has thermal past applied so that the heat is transferred into the AIO



Thermal grizzly, I did clean up that bottom right don't worry



This is how I do the spread method on CPUs and GPUs, I use my finger and wrap

Good write up! Surprised you didn't go custom loop with that case. 
 

EVGATech_DanielM
Good write up! Surprised you didn't go custom loop with that case. 
 

I tinker and change stuff out too often, custom loop sounds too much of a hassle for me haha

Dabadger84
Not gonna lie, I'm so out of it from being up so long cuz of how hyped I am I have a Hybrid card coming, that I legitimately went "Wait a minute, there is no card attached to that cooler dude!"
 

Wha!? Do you mean your Hybrid has shipped already?  Were you on the initial batch or yesterdays?

 
Nice, got me excited for mine eventually.   Where is your PSU?

AnTse
I got notified for my 3090 FTW3 cooler kit 12/10 and ordered.  Received today.  Just installed. So much quieter.  Just like I was back with my 2080ti Hybrid.  I am currently running about 15 degrees Celsius cooler under load.
 

Nice.  Back in September there was a huge thread about people saying the 2080ti Hybrid was horribly loud, countered also by a lot of people saying their 2080ti was quiet. I wasn't sure what to think.
 
  I believe it is the same Asetek 6 gen pump in the 3080 right?   As a fanatical quiet freak you had me at quieter

yaggaz
 
Nice, got me excited for mine eventually.   Where is your PSU?

The PSU is in the back of the case hidden away. These Lian Li Dynamic cases are legit, fit a lot, good cooling and cable management is easy.

Thanks a lot for this, really great write-up that answers many questions for people interested in the kit.

Which of your push/pull ML's are you controlling (speed) with iCUE vs PX1?
 
One last one.. Did you flash the Hybrid BIOS onto your card?

Thanks again.

tobincake1471
Thanks a lot for this, really great write-up that answers many questions for people interested in the kit.

Which of your push/pull ML's are you controlling (speed) with iCUE vs PX1?
 
One last one.. Did you flash the Hybrid BIOS onto your card?

Thanks again.

I'm using my motherboard and Argos monitor to set-up the speed of the fans.

Yes I did flash it, the XOC one.

I have the Razer badged version of the same case and I love mine

yaggaz

Dabadger84
Not gonna lie, I'm so out of it from being up so long cuz of how hyped I am I have a Hybrid card coming, that I legitimately went "Wait a minute, there is no card attached to that cooler dude!"
 

Wha!? Do you mean your Hybrid has shipped already?  Were you on the initial batch or yesterdays?

Yer, it'll be here Wednesday, I'm hyped a-f.  I queued Thursday, got my call up Friday - wasn't expecting it & had to work some magic to be able to actually purchase the card (resold my RTX 2070 Super on EBay that I was going to keep in the Step-Up queue for a 3080 but I yoloed it)
 
For those running air-cooled cards: Keep in mind your Power Limit will be "lower" if you're running your GPU fans at 100%.  Most people have found the happy medium if you're willing to go full blast, is 80%, this keeps keeps the card cool while not hampering the power limit as much.
For those running Hybrid cards (I can't confirm this til mine gets here) - I would not plug the radiator fans in to the card, again, for the same reason. Plug them in to your motherboard via a header/splitter instead to give you fan-control while they get power directly from the PSU or motherboard.  The reason I suggest this is those 120mm fans probably draw more power combined than the native on-board fans would on an air-cooled GPU, which again, could negatively impact your GPU's power limit, limiting your OC headroom etc.
I will test this myself, once I have one in hand, and see what effects it has on the power limit - I did this with the air-cooled 3080 I have and posted the numbers somewhere, can't remember exactly off the top of my head, but I believe it was something like a 13W draw difference just having the fans on vs off, for 80% fan speed, and going to 100% increased it by several watts from the 80% number.  Yeah, it's only a few watts (possibly two dozen at most), but why hamper your card's power limit ;)
More recently I actually disabled the RGB bar on the 3080 just to see what it does in terms of power draw - seems it too has a decent bit of draw, but I'd have to do some testing to see exactly how much it is, I think it's only around 3-5W though.  Maybe slightly more... I leave it on most of the time, but next time I'm running benchmarks going for personal bests, I'm definitely disabling all the RGBs on the cardo.

Got my kit too today, not installing it until early tomorrow, I'm feeling lazy right now ahaha.
 
Edit: Nevermind the smudges on the box, I just wiped it with disinfecting wipes lol, can't never be too safe these days... It came pristine.
 
 
 

SeanDude05
So is there barely any heatsink for the VRMs?

Thats what I'm concerned about too.

SeanDude05

Carmen813

SeanDude05
So is there barely any heatsink for the VRMs?

Thats what I'm concerned about too.

Cause I know in the Kingpin image of the kit you can see the gold colored heatsink, but in OPs images on page 1, it looks as if there are no substantial heatsinks behind the shroud fan, due to the thermal pad strips where the VRM rows are and then..... nothing behind/under the fan itself?

I read through installation guide and I can see the vrms have pads, but I'm not sure if they are direct contact to the shroud or if a heatsink is present.
It is listed in installation guide as having VRM heatsinks....might be ae just don't see them in pic. Ill update when I get mine this week.

Do you know the max fan rpm for the included fans? If they're fast enough I want to do push pull. And did you need to switch to the hybrid bios or can you keep the xoc beta bios air cooled version?