So I ran a 7 minute stress/load test using OCCT 4.0 and it passed without errors. Im planning on running another one but for 4 hours to see how my beast holds up and what the temps are like.

I hope to be in here soon

Btw, i will update the thread later tonight.. so long since i've been properly on the forum, so sorry for that guys..!.. i will update and send pm to those who didn't write their #Batch to me..

if they don't write back any time soon i will have to be creative ;)

IstBarP

=TRA=T-Bone
I would like to be a part of the club! Check out my Mods Rigs I benched Both 3dmark11 and Vantage At 5.175GHz!!! With a 2700K and a Corsair H100!!!

You have to link pictures of linx and so on (see page 1 for more information) ;).. 

PanzerMensch 
I hope to be in here soon  

 
You have the same cpu and motherboard as me, so you should be able to reach about the same as me.. with my h60 i almost made it to 5.2 ghz!.. though at 5.2 ghz, it became to hot for me and reached 85 degrees under linx..  

 
Noice!

Here is my 5.366Ghz run. No linx run but it took me a couple hours of testing to get this score for Hwbot.
If that's not good enough here is a SuperPI 32m run @ 5.393Ghz for 7 plus mins.
Water cooled with H50. lol
Edit: 2600K
Batch# 3049A357
vcore 1.624v

 
Used validator, can't get you a new one until I finish installing my new crosshair V, but computer is the same minus that board. Went from SB to CV

I got linx to run with the settings that were laid out, but even though it ran for 17 minutes I got absolutely no progress like you guys did. Am I doing something wrong? screeny below
 

20000 problem size would normally take a min or two tops

lordshinro

I got linx to run with the settings that were laid out, but even though it ran for 17 minutes I got absolutely no progress like you guys did. Am I doing something wrong? screeny below
(Picture)
 

1. Can you upload a better picture? :).. cant see the numbers and such in the CPU-Z :).. 
2. finally and AMD in here ;).. your the first one with an AMD Cpu, that tries to join ;).. (Not because i am an AMD fanboy, but more that it is all 2500k and 2600k in here.. and ofc one 2700k :))


To everyone ELSE regarding benches!
All of those who are questioning whether their cpu-z validation and such (not to say 3DMark) is fine , It is not.. you have to go through the SAME benchmark as everyone else, and I made a guide that shows you how you should set it up at the front page of this thread!.. 

And Thread updated, to those who met the requirements! :)

lordshinro

If you right click and click view image it should give you the full rez image and let you xoom in. I'll post the direct link below

IMG Link: http://i.imgur.com/3BqXV.jpg

(image)     

nice, i am off to bed now, but for now you're on the list! ;) (gonna add you there tomorrow while i am in school anyways :D)

Welcome to the 5 ghz Club! ;) if you have time for it, see if you can get a package done :).. 

http://www.overclock.net/t/649258/the-amd-linx-stable-club

if you see that link, it seems like linx registers fine? :).. maybe you have to have an amd version? 

lordshinro

I'll do my best to find one that runs, otherwise will you take any other cpu tests? Prime95?

we'll look at it if you can't get the other linx to work, but for now you're in :) 

Here's my 2500k @ 5.0 ghz
 

lordshinro

Cool beans, I'll try running the linked linx test tonight. Thanks again!

Nice!.. looking forward to see it! :D Adding you now! ;) (pm me your cooling please! :D)

huf757

Here's my 2500k @ 5.0 ghz
(Picture) 

Welcome to the 5 Ghz Club, your welcome to take the 5 Ghz club banner at the front page for your signature and link it to your post! ;).. 

Adding you now :).. (PM me your batch and what cooling you used! :))

I will now experiment with getting to 5.3 ghz seems I have a good cpu.