EVGA

Issues with Marvell Sata 6 Controller

Author
Post
Essentials Only Full Version
rjradical
New Member
  • Total Posts : 13
  • Reward points : 0
  • Joined: 2010/08/03 11:52:34
  • Status: offline
  • Ribbons : 0
2011/08/18 17:56:45 (permalink)
The problem is that on initial boot up the computer hangs for about 3 minutes with the following message:
Marvell 88SE91xx Adapter - BIOS Version 1.0.0.1029.
Initializing...
 
Originally the message was for BIOS version 1.0.0.1012 and also hung for 3 minutes, but I just updated the firmware in anticipation of getting a SATA III SSD. Still the computer hangs and the driver (1.0.0.1042) has been updated. I went into  the Marvell Bios with Control-M and could not get anything but the pop-up [wizard configuration] (or something along those lines).
 
Inside the Marvell Bios was the following information.
Vendor ID:1B4B
Device ID: 9123
Revision ID: B1
BIOS: 1.0.0.1029
Firmware Version: 2.2.0.118
PCIe Speed Rate: 5.0 GPS
Configure SATA as: AHCI Mode
Support Mode: Raid0 Raid1
 
Any idea what is going on or do I need to RMA this board? 
EDIT: Nothing is currently connected to the SATA III ports
 
post edited by rjradical - 2011/08/18 21:01:54

Motherboard: EVGA 770 
Video Card: EVGA GTX460 1GB
Optical : 2 Combo units
Memory: 3 X 2GB Mushkin Redline
Crucial M4 128GB
2 1TB Seagates
Case: Silverstone TJ07
PSU: Enermax MODU87+ 900W
#1

5 Replies Related Threads
    PINKTULIP
    FTW Member
    • Total Posts : 1158
    • Reward points : 0
    • Joined: 2007/06/03 16:01:19
    • Location: EARTH
    • Status: offline
    • Ribbons : 7
    Re:Issues with Marvell Sata 6 Controller 2011/08/18 19:01:31 (permalink)
    Go to the Bios load default then save and exit..see it fix also chk the Sata cable along with power cable just to make sure they are connected properly..

    MOBO :EVGA X299 DARK 151-SX-E299-KR  BIOS :1.29 CPU : Intel Core i9-10900X Skylake-X 10-Core 3.7 GHz  LCR :Corsair Hydro Series H80i V2 GPU :SAPPHIRE NITRO+ RX 6900 XT SE MEMORY: CORSAIR Dominator Platinum SE Torque 32GB (4 x 8GB) CMD32GX4M4C3200C14T SSD 01: SAMSUNG 970 PRO M.2 1TB NVMe SSD 02: SAMSUNG 860 PRO 256GBX2 Raid 0 PSU : Seosonic Prime Titanium SSR-1000TR 1000 Watts CASE :Thermaltake (Armor+) VH6000SWA SC :Creative Sound Blaster AE-9 5.1 Channels Monitor  Acer XR382CQK  IPS 3840x1600 @ 75HZ BD [/
    #2
    rjradical
    New Member
    • Total Posts : 13
    • Reward points : 0
    • Joined: 2010/08/03 11:52:34
    • Status: offline
    • Ribbons : 0
    Re:Issues with Marvell Sata 6 Controller 2011/08/18 21:01:03 (permalink)
    Everything is connected properly. I just updated the Bios (82) and sata controller firmware.
     
    One thing I didn't mention is that no drives are connected to the sata III ports. Would that cause the problem.
    (Will edit initial post) 

    Motherboard: EVGA 770 
    Video Card: EVGA GTX460 1GB
    Optical : 2 Combo units
    Memory: 3 X 2GB Mushkin Redline
    Crucial M4 128GB
    2 1TB Seagates
    Case: Silverstone TJ07
    PSU: Enermax MODU87+ 900W
    #3
    PINKTULIP
    FTW Member
    • Total Posts : 1158
    • Reward points : 0
    • Joined: 2007/06/03 16:01:19
    • Location: EARTH
    • Status: offline
    • Ribbons : 7
    Re:Issues with Marvell Sata 6 Controller 2011/08/19 06:20:37 (permalink)
    not realy......................if you are not planning to use Sata III SSD  then disable it in the Bios...

    MOBO :EVGA X299 DARK 151-SX-E299-KR  BIOS :1.29 CPU : Intel Core i9-10900X Skylake-X 10-Core 3.7 GHz  LCR :Corsair Hydro Series H80i V2 GPU :SAPPHIRE NITRO+ RX 6900 XT SE MEMORY: CORSAIR Dominator Platinum SE Torque 32GB (4 x 8GB) CMD32GX4M4C3200C14T SSD 01: SAMSUNG 970 PRO M.2 1TB NVMe SSD 02: SAMSUNG 860 PRO 256GBX2 Raid 0 PSU : Seosonic Prime Titanium SSR-1000TR 1000 Watts CASE :Thermaltake (Armor+) VH6000SWA SC :Creative Sound Blaster AE-9 5.1 Channels Monitor  Acer XR382CQK  IPS 3840x1600 @ 75HZ BD [/
    #4
    PINKTULIP
    FTW Member
    • Total Posts : 1158
    • Reward points : 0
    • Joined: 2007/06/03 16:01:19
    • Location: EARTH
    • Status: offline
    • Ribbons : 7
    Re:Issues with Marvell Sata 6 Controller 2011/08/19 06:37:13 (permalink)
    rjradical

    Everything is connected properly. I just updated the Bios (82) and sata controller firmware.

    One thing I didn't mention is that no drives are connected to the sata III ports. Would that cause the problem.
    (Will edit initial post) 

    Can u switch SATA cable or SATA Port?I ment 0 to 1 or 1 to 0? 


    MOBO :EVGA X299 DARK 151-SX-E299-KR  BIOS :1.29 CPU : Intel Core i9-10900X Skylake-X 10-Core 3.7 GHz  LCR :Corsair Hydro Series H80i V2 GPU :SAPPHIRE NITRO+ RX 6900 XT SE MEMORY: CORSAIR Dominator Platinum SE Torque 32GB (4 x 8GB) CMD32GX4M4C3200C14T SSD 01: SAMSUNG 970 PRO M.2 1TB NVMe SSD 02: SAMSUNG 860 PRO 256GBX2 Raid 0 PSU : Seosonic Prime Titanium SSR-1000TR 1000 Watts CASE :Thermaltake (Armor+) VH6000SWA SC :Creative Sound Blaster AE-9 5.1 Channels Monitor  Acer XR382CQK  IPS 3840x1600 @ 75HZ BD [/
    #5
    rjradical
    New Member
    • Total Posts : 13
    • Reward points : 0
    • Joined: 2010/08/03 11:52:34
    • Status: offline
    • Ribbons : 0
    Re:Issues with Marvell Sata 6 Controller 2011/08/20 22:36:54 (permalink)
    I disabled the SATA III controller and it boots fine. Will re-enable it when I upgrade to a SATA III SSD.

    Motherboard: EVGA 770 
    Video Card: EVGA GTX460 1GB
    Optical : 2 Combo units
    Memory: 3 X 2GB Mushkin Redline
    Crucial M4 128GB
    2 1TB Seagates
    Case: Silverstone TJ07
    PSU: Enermax MODU87+ 900W
    #6
    Jump to:
  • Back to Mobile