Today I updated BIOS on my X299 Dark from 1.28 to 1.29. If I am correct BIOS’ hardware monitor reports NXP MCU temperatures are approximately 2C higher after the update than they were before. Has anybody else observed same?

I installed this update, and updated my GTX 1080 with this software:

I was attempting to install windows 11 and this driver allowed me to disable CSM, I had no video output in BIOS until I installed that driver. I installed it and I was able to disable CSM and still have video output. I booted into windows to make sure everything was ok and it seemed so. So I went back into BIOS to enable Secure Boot and my problems returned, only this time I couldnt bypass BIOS Setup into Windows to flash the BIOS. I am stuck with no video and a POST code of D6, No Console Output Devices are found. Tried another GPU and the same issue is present, D6. So my motherboard just doesn't detect GPUs anymore? Its fans run and it lights up. Any suggestions? Thanks!

looks like another update is needed..
 

EVGATech_LeeM
New Updates for X299 Motherboards today.  This updates the ME for an Intel security vulnerability:

BIOS 1.29 (E299 Dark) / 1.29 (E297 FTW K) / 1.22 (E296 Micro ATX 2) /1.30 (E295 Micro) Updates 

• Update ME firmware to 11.12.90.1962v10 for Intel security vulnerability.
  

 

---

​

Windows Installation

• Download the correct .zip file below for your motherboard:        

         151-SX-E299-KR - EVGA X299 Dark - v1.29
        142-SX-E297-KR - EVGA X299 FTW K - v1.29
        121-SX-E296-KR - EVGA X299 Micro ATX 2 - v1.22
        131-SX-E295-KR - EVGA X299 Micro ATX - v1.30

• First go into your BIOS and load defaults, save and exit
• Close all open programs.
• Go into the folder where you unzipped this package and double-click update.bat
• Press Y to start the flash process
• DO NOT TURN OFF POWER OR RESET DURING THE FLASH PROCESS
• After the flashing is finished, the system will automatically shut down. Then power on again and go into BIOS to setup.
• NOTE: If flash box immediately closes after flash attempt, the flash may need to be ran from a CMD prompt with administrator privileges or DOS version.

  
BIOS Installation

• Extract the contents of .zip file to USB flash drive (must be formatted as FAT32)
• Reboot the machine and go into the system BIOS
• From the BIOS, navigate to the Save & Exit tab and open "Select BIOS File."
• Select the .bin file you wish to flash.

 
Please let me know if anyone runs into problems with this update.  Thanks!

I am requesting new BIOS 1.30 because I believe when Above 4G Decoding Enable in the Bios 1.28 and 1.29 it cause USB Device not detected time to time!!!!!!!!!

PINKTULIP
I am requesting new BIOS 1.30 because I believe when Above 4G Decoding Enable in the Bios 1.28 and 1.29 it cause USB Device not detected time to time!!!!!!!!!

Lee already replied in your thread.

I'm having an issue with virtualization not working after the latest bios 1.29 update on x299 Dark can anyone confirm that it does work? its enabled in bios but shows disabled under windows,
 
any help would be great! cant run any vm software. Customer service also does not pick up phone calls on Monday 11-21-22 maybe early thanksgiving vacay?

ocbonesI'm having an issue with virtualization not working after the latest bios 1.29 update can anyone confirm that it does work? its enabled in bios but shows disabled under windows, any help would be great! cant run any vm software. Customer service also does not pick up phone calls on Monday 11-21-22 maybe early thanksgiving vacay?

 
I'm running VMWare Workstation Pro V16 on X299 Dark BIOS 1.29 and Win10 host without any issues.

ocbones
I'm having an issue with virtualization not working after the latest bios 1.29 update can anyone confirm that it does work? its enabled in bios but shows disabled under windows,
 
any help would be great! cant run any vm software. Customer service also does not pick up phone calls on Monday 11-21-22 maybe early thanksgiving vacay?

Not sure what issues you're having with the phone system.  We did restart our phone system a little earlier today, but support is still in the office and answering calls for another hour today.

Hi,
 
Would it possible to compile a new BIOS with the latest Intel ME security update?


Thanks in advance.

Intel Management Engine (ME/AMT) Firmware Version 11.12.93.2323

 
https://station-drivers.c...-and--5Mo)/lang,en-us/

hi,
this might be a weird place to ask but is it possible to have a bios that allows disabling of HT on only specific cores?