Haven’t looked for the classified tool yet. Using the stock loaded ln2 bios and kinda expect more from the kp versus my ftw3. Haven’t seen board draw over 470w yet.
Lots more tinkering to do tho

Got my Hydro Copper in!! Swapped from AIO to block, used liquid metal and 12.8w/mk pads. On it's own loop w/360 60mm rad in push + pull. Classified tool used, and on OLD version of 3dmark before anyone asks. 
 
Think I have a nice piece of silicon here! :)
 
3dmark.com - PR - 16,312

Really nice score!!

magillaman
Got my Hydro Copper in!! Swapped from AIO to block, used liquid metal and 12.8w/mk pads. On it's own loop w/360 60mm rad in push + pull. Classified tool used, and on OLD version of 3dmark before anyone asks. 
 
Think I have a nice piece of silicon here! :)
 
3dmark.com - PR - 16,312

Nice score and temps. What thermal pads thickness did you use for front and backplate? Thank you

magillaman
Got my Hydro Copper in!! Swapped from AIO to block, used liquid metal and 12.8w/mk pads. On it's own loop w/360 60mm rad in push + pull. Classified tool used, and on OLD version of 3dmark before anyone asks. 
 
Think I have a nice piece of silicon here! :)
 
3dmark.com - PR - 16,312

What'd you push voltage to to hit that clock stable enough to bench?  That's an impressive score indeed.

SoldierRBT
Nice score and temps. What thermal pads thickness did you use for front and backplate? Thank you

Ty! 2mm on vram for both sides.
+ another 2mm pad on top of the backplate with big aluminum heatsink and fan.

Dabadger84
What'd you push voltage to to hit that clock stable enough to bench?  That's an impressive score indeed.

Same NVVDD, LL, and Mem as before, only increased MSVDD to 1.09375 and the vram is much cooler with the block + new pads so I was able to push it to +1750

Nice

magillaman

SoldierRBT
Nice score and temps. What thermal pads thickness did you use for front and backplate? Thank you

Ty! 2mm on vram for both sides.
+ another 2mm pad on top of the backplate with big aluminum heatsink and fan.

Dabadger84
What'd you push voltage to to hit that clock stable enough to bench?  That's an impressive score indeed.

Same NVVDD, LL, and Mem as before, only increased MSVDD to 1.09375 and the vram is much cooler with the block + new pads so I was able to push it to +1750

I swear I got the worst Memory on any Kingpin that's reported performance numbers on these forums LOL I couldn't do more than +1250 in SOME benchmarks on the AIO cooler, now it's 50/50 on whether or not I can get anything over 1300 to pass at stock voltage, without going over 1.4V Mem voltage it won't go a tick higher.  I did get 1400 to pass Port Royal with 1.4125V, but it only passed it 2 outta 4 times, so either PCB heatsoak was kicking in, or it was not very stable.  My core is pretty good, memory is KekW.
 
 

Sounds like a tough break on memory 😄🤣

magillaman
Got my Hydro Copper in!! Swapped from AIO to block, used liquid metal and 12.8w/mk pads. On it's own loop w/360 60mm rad in push + pull. Classified tool used, and on OLD version of 3dmark before anyone asks. 
 
Think I have a nice piece of silicon here! :)
 
3dmark.com - PR - 16,312

Wow! that is crazy good, What was your core max before swap?
 
I got my block in, but not sure I would gain much with it. So debating just keeping it around in case AIO fails. My effective core max is like 2205.