telehog

elbramso
Was able to score past 16k. Love this card^^

Congrats on top 50 HOF PR : 16 082  That card will go faster with some more cooling !

Thanks. I need some support from cooler weather then 😉
Unfortunately my Hydrocopper Kit isn't mounted very well. Still seeing delta t of 23c at 600w of load

elbramso
Was able to score past 16k. Love this card^^

Nice score and good temps. What settings did you use? Wattage on that run?

SoldierRBT

elbramso
Was able to score past 16k. Love this card^^

Nice score and good temps. What settings did you use? Wattage on that run?

Custom curve
1360 mem
Nvvdd 1.20625
Fbvvd 1.4375
Msvdd 1.1625
Both load lines lvl 1
~ 600w

Got the train wreck set up again in SLI ! Saturday night down  0 F . Just did this today should do a lot better Saturday before loop slushes up.  http://www.3dmark.com/pr/1369933

Just pulled the trigger on my Kingpin, should be here next week! I'm watching this thread with great interest. 
Hope I'm not making a mistake, my FTW3 3090 get 14.9K in PR(Optimus waterblock), I want to at least get that! 
 
My Kingpin block is on order from Optimus, but it will be a while before it gets here. 
 
-J

Just got my Kingpin Hybrid. Watched LUUMIs overclock guide, flipped front switch to OC bios, and have been playing with numbers in X1.
 
 
The score is abysmal. I am very disappointed atm. The temps are too high, too. I don't want to push it any further because its not doing much.
 
 
I have no touched the switches on the back. I am yet to find any info on what they do (nothing in the box but few pages with no info on switches). Also have not flashed the card. Which bios are you guys using? What can I do differently?
 


Must add, even though GPU-Z is showing 2220MHz max - I never see that number on the cards built in display. It never goes over 1920 and mostly stays in 1800-1900 range.

maxenko
Just got my Kingpin Hybrid. Watched LUUMIs overclock guide, flipped front switch to OC bios, and have been playing with numbers in X1.
 
 
The score is abysmal. I am very disappointed atm. The temps are too high, too. I don't want to push it any further because its not doing much.
 
 
I have no touched the switches on the back. I am yet to find any info on what they do (nothing in the box but few pages with no info on switches). Also have not flashed the card. Which bios are you guys using? What can I do differently?
 


Must add, even though GPU-Z is showing 2220MHz max - I never see that number on the cards built in display. It never goes over 1920 and mostly stays in 1800-1900 range.

Umm... Says you're pulling 750 w and 90c mem/75c core. What bios is on that thing? Something is way wrong.

USMC1419
Umm... Says you're pulling 750 w and 90c mem/75c core. What bios is on that thing? Something is way wrong.

Bios version is in the screenshot. Btw, I have not installed any BIOS on it. This is what EVGA sent me.

maxenko

USMC1419
Umm... Says you're pulling 750 w and 90c mem/75c core. What bios is on that thing? Something is way wrong.

Bios version is in the screenshot. Btw, I have not installed any BIOS on it. This is what EVGA sent me.

Card must have had the 1000W BIOS installed on it.  Don't think you could draw that much power otherwise.

maxenko
 

Must add, even though GPU-Z is showing 2220MHz max - I never see that number on the cards built in display. It never goes over 1920 and mostly stays in 1800-1900 range.

Your temps are probably taking the clock bins down.  It's very sensitive to temperature.  Once you hit that threshold, the GPU will start knocking off OC bins, regardless of what the max is.  I think it's super low, like mid-40C-something where that starts to occur.  With you hitting 70c, it makes sense the OC is getting knocked down.  You probably either need colder ambient, or ditch the stock hybrid cooling solution and put it under water.  Once you start putting off that much heat, like 700W, that stock AIO won't do you good.