LVNeptune
Where exactly did you see vrel and vop? Those relate to voltages and not being able to boost higher due to voltage limit. I don't see it hit in your screenshot. Looks idle all the way across.
 

I took the screenshot too late. I'll have to repeat it.
 
Do these numbers look decent so far?

I think so. With no tweaking getting 14700 is great. Classified should send you beyond 15,000 for sure.

LVNeptune
I think so. With no tweaking getting 14700 is great. Classified should send you beyond 15,000 for sure.

Alright, I'll keep trying. I wish I knew how to make custom curves and set the right voltages in classified. I'm trying to figure it out.

Oh, and what does "Both NVVDD switches on" mean? I have the LN2/OC/Norm switch, but are these physical switches?
 
What are some max numbers for NVVDD, FB and MS for classified to not exceed? Always stay on load line 1? And keep on OCP to be safe?
 
I tried searching around google and youtube for pointers on how to do this, and didn't find anything :(

USMC1419
Oh, and what does "Both NVVDD switches on" mean? I have the LN2/OC/Norm switch, but are these physical switches?
 
What are some max numbers for NVVDD, FB and MS for classified to not exceed? Always stay on load line 1? And keep on OCP to be safe?
 
I tried searching around google and youtube for pointers on how to do this, and didn't find anything :(

There's physical DIP switches.

https://www.3dmark.com/3dm/55284398
 
How does this look? +150 core, +0 mem, max power and voltage slider on PX1, max fans. 498w and 118% TDP.
 
Looks like I'm at a mix of vrel vop and vpwr. On my FTW3 Hybrid I was always limited by the green power limit wall.
 
And where are these dip switches on the card? Are they on by default, and what do they do?
 
Edit: Just realized my power slider was 119% and not 121% this whole time. Not sure how much of a difference this will make. About to try +1000 mem

Try closing all apps except PX1 minimized.  Shutdown all unnecessary services.  Quit bloated tray apps.  Don't run GPUZ or HWINFO.  Just watch frames and key scene transitions as guides in the test.  Fan load on the card affect performance, too.
 
That's a lot better than my FTW3.

808sting
Try closing all apps except PX1 minimized.  Shutdown all unnecessary services.  Quit bloated tray apps.  Don't run GPUZ or HWINFO.  Just watch frames and key scene transitions as guides in the test.  Fan load on the card affect performance, too.
 
That's a lot better than my FTW3.

I'll give that a try. I offloaded the 3x AIO fans to a controller with SATA power. So the only fan the KP has to power is the internal board fan.
 
Here's the run with +150 / +1000, same settings as before.
 
https://www.3dmark.com/3dm/55284767
 
Not sure if it'll be reaching 15.4k+, but I haven't really started to tweak it much at all with classified because I don't know how.
 

1500 memory, 160-165 clock at 20c or less starting temp with sustained 35-38c temps will get you in the low to mid 15's. I'm still trying to figure out the classified toll but as of right now it's lowering my numbers until I play with it more. Flying toaster is right, it's meant for LN2, if you want a good card to play around with a stock cooler get the FTW3 and save $200. Plus you have to listen to Metallica when overclocking or it won't work at all.

USMC1419
Oh, and what does "Both NVVDD switches on" mean? I have the LN2/OC/Norm switch, but are these physical switches?
 
What are some max numbers for NVVDD, FB and MS for classified to not exceed? Always stay on load line 1? And keep on OCP to be safe?
 
I tried searching around google and youtube for pointers on how to do this, and didn't find anything :(

Both on will set nvvdd to 1.15v. For the stock aio max would be 1.2 on nvvdd/msvdd & 1.4 on fbvdd.