I usually get notified by UPS My Choice before I get anything from EVGA. 

Talon2020
Ordered. Should be here tomorrow via next day air. Figure if I'm already spending this much on a GPU, an extra $60 isn't much. 

Agreed 

Meuric
Recieved Email - 12/15/2020 9:25 AM 
Purchased - 12/15/2020 9:47 AM

 
Congratulations!  Enjoy your K|NGP|N!
 

Cadillac94pimpin

enewt

Cadillac94pimpin
Thanks! Yea, I called support and then @ Jacob on Twitter but he asked if I had a ticket, but they did not give me a ticket, they just said they would get it fixed and I would get an order confirmation once it's fixed. Maybe he can help get it fixed. 

I'd give it another hour and if you don't have confirmation, I would call again.  You want to get the order in and done before 2 pm which is there internal shipping cutoff time.  You want the KPE to ship today!!!  
 
Again, congratulations!

He replied back on Twatter after he found my order, looked into it, then replied it should ship today. Hopefully it does. :) 

Noice!!!  Congratulations!
 
The internal shipping cutoff is apparently 2 pm (the first drop, they made an exception because they dropped the emails at 2:01 pm), so folks have about 20 minutes to get their orders in for them to ship today.  Good luck!

enewt, 
 
Thanks a ton for your help with this list and the advice to all. I placed my KPE order with EVGA sales' help (Missed my window, I was early on in the list but they sent me a new one today). Much much appreciated!

RawrBawr
enewt, 
 
Thanks a ton for your help with this list and the advice to all. I placed my KPE order with EVGA sales' help (Missed my window, I was early on in the list but they sent me a new one today). Much much appreciated!

Congratulations!  I am glad it all worked out.  Enjoy your KPE!!!

Cjdowd80
Going to ask this here as the community in this thread is responsive and been super helpful over the last month or so ... With me getting my KPE on Thursday, and still getting over my bricked 3090 Hybrid from last night (into my brothers PC), was wondering if anyone plans to run aftermarket fans or setups on the rad? Where the Rad is going in my O11-D XL case, i have 3x ML120 fans, and wasn't sure how i can use those. I noticed on the hybrid card last night, the fans connected to a header from the pump/GPU. If i am leaving the EVGA fans off, and go with the Corsair ML120 fans on the rad instead, would i just not use the cable for fan headers coming from pump, and go directly into my commander pro like they are now? Any help is appreciated, just curious how it'll work and what everyone's plans are. Thanks

I have a similar setup (O11 XL) and Corsair ML120 fans.  I plan on putting the Kingpin Rad in the front/side mount with the Kingpin fans in a push configuration then the Corsair ML120s in a pull configuration on the other side.  Then I have the 3 ML120s on the bottom as intake, and the H150i with 3 ML120s for output on the top, and 1 ML120 for output on the back.  I'll set a custom fan curve for the Kingpin Corsair fans in iCue.  
 
I haven't tested it yet but i believe you should be able to mount the rad like this and still put the side cover on :   (Inside case) ML120|Radiator|CaseWall|Kingpin Fans (Exterior of Case) 

tomorrow its our turn 

Stickboy46

Cjdowd80
Going to ask this here as the community in this thread is responsive and been super helpful over the last month or so ... With me getting my KPE on Thursday, and still getting over my bricked 3090 Hybrid from last night (into my brothers PC), was wondering if anyone plans to run aftermarket fans or setups on the rad? Where the Rad is going in my O11-D XL case, i have 3x ML120 fans, and wasn't sure how i can use those. I noticed on the hybrid card last night, the fans connected to a header from the pump/GPU. If i am leaving the EVGA fans off, and go with the Corsair ML120 fans on the rad instead, would i just not use the cable for fan headers coming from pump, and go directly into my commander pro like they are now? Any help is appreciated, just curious how it'll work and what everyone's plans are. Thanks

I have a similar setup (O11 XL) and Corsair ML120 fans.  I plan on putting the Kingpin Rad in the front/side mount with the Kingpin fans in a push configuration then the Corsair ML120s in a pull configuration on the other side.  Then I have the 3 ML120s on the bottom as intake, and the H150i with 3 ML120s for output on the top, and 1 ML120 for output on the back.  I'll set a custom fan curve for the Kingpin Corsair fans in iCue.  
 
I haven't tested it yet but i believe you should be able to mount the rad like this and still put the side cover on :   (Inside case) ML120|Radiator|CaseWall|Kingpin Fans (Exterior of Case) 

 
Still waiting for the spectre 3 that was delayed .its been a month already 

Order now showing as completed. Should see a tracking number soon!

order placed
 
Email received @ 9:25 AM