The dual ftw3 looks like my current corsair 760t black. Vn

sailorman50

Looks like people are starting to paint the EVGA logo on their Power Link.
I like it.

kraxe.tk

corndog1836

kraxe.tk
Anyone going the with MSi 1080 Ti Seahawk?  Would going with the FTW3 and adding a block be a better option.  Assuming the Hydro-copper will be the FTW3 PCB with block.  Or which card will be better MSI Seahawk or EVGA Hydro-copper?

that's what I am doing ...FTW3 plus EK block...I need the fans on the FTW3 for foutr reasons
1. ek block comes out late may
2. I could give this card to my daughter in a year to replace her gtx 1070 if I upgrade
3. if loop ever breaks down
4. if I upgrade to volta, I can sell the card easily with the air cooler
 
I had the same question you did a couple weeks ago.   I bought FTW3 and have since emailed EK and found out FTW3 waterblock will be out by first week of june
 

corndog1836   Did you see the MSI Seahawk with waterblock?  https://www.newegg.com/Product/Product.aspx?Item=N82E16814137144&cm_re=1080_ti_seahawk-_-14-137-144-_-Product It's around $50 more than the FTW3, so when you add a waterblock to the FTW3, it will cost maybe $100 more than the Seahawk.  Very close to $950, is the FTW3 route worth it?  You guys think the FTW3 is a better overclocker and better equipped than the MSI.  Or am I a lame EVGA fanboy, that bought into that powerlink adapter also.  Hah, darn I have SLI waterblock setup currently, and planned to swap to a single 1080 Ti.  I think I want to wait for a waterblock, it will make it a little easier.  I don't want to do extra steps..  Water to air and back to water, or water to water.  My FTW3 should be here in a couple days.

Yes but i need the fans for resale or to put in secondary system later

Here's mine. 
 
 

@EVG_JacobF
 
Hi, I cant order any GPU's from the euro online store, it gives me this error page, can you look into it or to i need to open a ticket?
 
 
 

 




 

Just got mine today :)

Very nice.. Both run stable at 2012mhz and memory +200

Ghost recon wildlands runs at 60fps in 4k with ultra settings.

Not tested any more so far.

Edit : can't upload a picture.. Stopps at 34%..

SomeOne1085
Just got mine today :)

Very nice.. Both run stable at 2012mhz and memory +200

Ghost recon wildlands runs at 60fps in 4k with ultra settings.

Not tested any more so far.

Edit : can't upload a picture.. Stopps at 34%..

You're running 2 in sli? Can both your cards sustain 2012 Mhz while playing intensive games for more then a few minutes? If so, you got 2 good cards. I can get both mine over 2000, but they both will settle back to around 1964 Mhz and will stay there with my fan profile set to aggressive. Also, you should be able to set your memory to +400 or 500 without too much of an issue

Islandborn
You're running 2 in sli? Can both your cards sustain 2012 Mhz while playing intensive games for more then a few minutes? If so, you got 2 good cards. I can get both mine over 2000, but they both will settle back to around 1964 Mhz and will stay there with my fan profile set to aggressive. Also, you should be able to set your memory to +400 or 500 without too much of an issue

Both remain there.. But have not tested it longer than one hour yet

SomeOne1085

Islandborn
You're running 2 in sli? Can both your cards sustain 2012 Mhz while playing intensive games for more then a few minutes? If so, you got 2 good cards. I can get both mine over 2000, but they both will settle back to around 1964 Mhz and will stay there with my fan profile set to aggressive. Also, you should be able to set your memory to +400 or 500 without too much of an issue

Both remain there.. But have not tested it longer than one hour yet

Wow...surprising you can do that especially with your top card. My top card even with fan at 95% will get above 70C. Can u snap a pic of your Precision X open so I can see your settings? Thanks.