What RAM and RAM blocks are you using? Looks great!

Looks amazing. I personally would have gone with White Fans or Fans with a White LED to go with the rest of the build.
What are you using for a pump?

I see white tubing in there... anyone else see it? :)

scottalot

I see white tubing in there... anyone else see it? :)

Yes sure white tubing why not?

farthestkris


i dont like the white PCI-E wiring and the tubing is a bit small oh and also white Led fans ?  other than that looks great !


you can checkout my build here  http://www.youtube.com/watch?v=xVIjf8wPMgk

the tubing is big enough for a good cooling result i dont like high flow needs to much of space and the cooling is not realy better
 
And the red fans is a tribute to the similar red EVGA slots

Worf1234

farthestkris


i dont like the white PCI-E wiring and the tubing is a bit small oh and also white Led fans ?  other than that looks great !


you can checkout my build here  http://www.youtube.com/watch?v=xVIjf8wPMgk

the tubing is big enough for a good cooling result i dont like high flow needs to much of space and the cooling is not realy better

And the red fans is a tribute to the similar red EVGA slots

the red fans are ... interesting lol i would put white ones on IMO

Great rig.  Why do you use two pumps?  How much does the water cooling cost you?

Nice build you have there.
 
Just curious, how did you get the board to fit in the 800D? It doesn't look like you used the Mtn Mods tray, and I can't see the middle divider over the PSU cut in any way, yet it does look like you sacraficed the 4th pci-x slot.  If you did cut it, then it must be a very well done.
 
Cheers,
Alan

i think it looks great

Worf1234

Alanw

Nice build you have there.

Just curious, how did you get the board to fit in the 800D? It doesn't look like you used the Mtn Mods tray, and I can't see the middle divider over the PSU cut in any way, yet it does look like you sacraficed the 4th pci-x slot.  If you did cut it, then it must be a very well done.

Cheers,
Alan

 

You see right

Im not using the mtn mods tray

I modified the orginal tray with new holes for the hptx form factor,open the slots from 7 to 9

and take the midplate between psu and motherboard a little bit deeper

Thanks for the information, and the picture.
 
I'm having a difficult time with my 800D. If you don't mind another question.  Did you cut the mid-plate in half just below the hot-swap drive bay? I can see that yours is lower and detached now, but I cannot tell if you left the remainder of the mid-plate under the drives in-tact.
 
I'm considering just removing the mid-plate all together, but I would prefer to keep the drive assembly where it's currently located.
 
Last question. Did you modify the hole in the 800D's tray so that you can access both CPU mounting hardware from the rear panel?
 
Thanks again,
Alan

Alanw

Worf1234

Alanw



Did you modify the hole in the 800D's tray so that you can access both CPU mounting hardware from the rear panel?

Thanks again,
Alan

No im fixed this hptx board only with new distanceholder and holes on the tray,acces from back im not realy need

post edited by Worf1234 - 2010/12/17 12:33:47

Very nice ... :-)
 

A little bit more impressions 
 

deathhorse

dude that thing is sweet

No not sweet i've tried it now ,the case tastet like metal
Thanks man

Dude This Rig is Freaking Awesome Would Like to see some temp Posts and also why didnt you go with the koolance mosfet cooling blocks for the board??? 
 
 
 
but you get +10    A+          Tango Out.