EVGA

Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine

Author
Post
Essentials Only Full Version
mrshrir
Superclocked Member
  • Total Posts : 179
  • Reward points : 0
  • Joined: 2018/11/28 13:34:41
  • Status: offline
  • Ribbons : 0
2019/09/14 02:02:06 (permalink)
card is a 2080ti xc hybrid , does someone have pictures of what needs to be connected to where and how exactly is this mod supposed to be done, my cable will be arriving soon, and im not entirely sure what header i need to disconnect on the the card, also, where do you thread this wire through ? is there a gap small enough between the two  8 pin connections ? ive head that even lowering to 90 percent pump speed does eliminate the coil whine ? 
#1

7 Replies Related Threads
    DeadlyMercury
    iCX Member
    • Total Posts : 422
    • Reward points : 0
    • Joined: 2019/09/11 14:05:07
    • Location: Moscow
    • Status: offline
    • Ribbons : 14
    Re: Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine 2019/09/14 04:27:14 (permalink)
    Same here - was trying to figure out how I should remove only shroud, not radiators or something, from evga hybrid kit installation manual - but still have some questions.
    If somebody did that mode with xc or ftw3 and made pictures of that - that would be perfect.

    "An original idea. That can't be too hard. The library must be full of them."
    Stephen Fry
    #2
    mrshrir
    Superclocked Member
    • Total Posts : 179
    • Reward points : 0
    • Joined: 2018/11/28 13:34:41
    • Status: offline
    • Ribbons : 0
    Re: Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine 2019/09/14 04:59:02 (permalink)
    removing the shroud isnt that hard, you just need to unscrew all the screws on the backplate, except those that hold the pump in place, you also need to remove the bracket at the back .
    #3
    mrshrir
    Superclocked Member
    • Total Posts : 179
    • Reward points : 0
    • Joined: 2018/11/28 13:34:41
    • Status: offline
    • Ribbons : 0
    Re: Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine 2019/09/14 05:01:28 (permalink)
    this is all i found on youtube, its for the FTW HYBRID 
     
    https://www.youtube.com/watch?v=M-SJ-_tAfug
     
    #4
    mrshrir
    Superclocked Member
    • Total Posts : 179
    • Reward points : 0
    • Joined: 2018/11/28 13:34:41
    • Status: offline
    • Ribbons : 0
    Re: Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine 2019/09/14 05:03:12 (permalink)
    then i understood that you can use this program "ARGUS MONITOR" which always you to control the percentage of a Fan header which is set to DC MODE,
     
    #5
    DeadlyMercury
    iCX Member
    • Total Posts : 422
    • Reward points : 0
    • Joined: 2019/09/11 14:05:07
    • Location: Moscow
    • Status: offline
    • Ribbons : 14
    Re: Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine 2019/09/14 06:12:53 (permalink)
    mrshrir
    removing the shroud isnt that hard, you just need to unscrew all the screws on the backplate, except those that hold the pump in place, you also need to remove the bracket at the back .

    So thats's the point: I guess you don't need to unscrew ALL screws: some of them holding RAM plate or VRM radiators and according to installation manual you screw them first - than screw shroud.
    I don't want to unscrew all screws and want to unscrew only shroud screws.

    "An original idea. That can't be too hard. The library must be full of them."
    Stephen Fry
    #6
    DeadlyMercury
    iCX Member
    • Total Posts : 422
    • Reward points : 0
    • Joined: 2019/09/11 14:05:07
    • Location: Moscow
    • Status: offline
    • Ribbons : 14
    Re: Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce coil whine 2019/09/14 06:21:07 (permalink)
    btw: so the pump controlled over voltage only, no PWM? Does it report its rpm?
     

    "An original idea. That can't be too hard. The library must be full of them."
    Stephen Fry
    #7
    ty_ger07
    Insert Custom Title Here
    • Total Posts : 21171
    • Reward points : 0
    • Joined: 2008/04/10 23:48:15
    • Location: traveler
    • Status: offline
    • Ribbons : 270
    Installing 4-Pin PWM Connector to 4-Pin Mini GPU Fan Connector to reduce pump noise. 2019/09/14 06:58:31 (permalink)
    To reduce coil whine? No. To reduce pump noise.

    Coil whine has a specific unrelated meaning.

    ASRock Z77 • Intel Core i7 3770K • EVGA GTX 1080 • Samsung 850 Pro • Seasonic PRIME 600W Titanium
    My EVGA Score: 1546 • Zero Associates Points • I don't shill
    #8
    Jump to:
  • Back to Mobile