redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
I'm about 6+ months in with this board. Have made no changes (other than update to bios 2.01, which unfortunately doesn't seem to include any of the pre-saved profiles that the prior version included...). Otherwise, cpu / memory all compatible etc. Using o/c robot settings for cpu and xmp profile for ram. As of a week or so ago, the boot process started showing issues. First boot sequence started taking longer than usual (e.g., went from 15-30 seconds to 60 seconds, so markedly different). Now, post sequence seems to hang at post code 10, with CATERR light off and before the VCCIO_1_2 Status lights up. It hangs in that state for about 60 seconds, turns off and recycles to the same state (i.e., loops in this state). If i restart via CMOS Reset Button, i am sent back into the bios where i can reload the prior profile, save and restart, and get into the OS thereafter without issue....
|
Sajin
EVGA Forum Moderator
- Total Posts : 49165
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: offline
- Ribbons : 199
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/13 09:33:36
(permalink)
Sounds like the issue is related to the overclock you’re running. No issues at optimized defaults?
|
redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/13 09:46:03
(permalink)
Thanks for the quick response Sajin, it's a 5.1 OC (with core 1 and 2 @ 5.2) on a 10900k at defaults. And i'm not benchmarking or otherwise pushing the cpu. I've had the same OC since day 1 (plus core 1 and 2 @ 5.3 and some minor tweaks to voltages) that ran stable (i.e., not a single crash). So I didn't really focus on this minor OC as the possible issue... in any case, i haven't tried @ defaults, but what are 'optimized' defaults?
|
Sajin
EVGA Forum Moderator
- Total Posts : 49165
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: offline
- Ribbons : 199
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/13 09:55:23
(permalink)
Optimized defaults is when you press F7 in your bios and are prompted to load optimized defaults which are the default settings for the board.
|
redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:23:01
(permalink)
Pressing F7 in bios loads the 'saved profiles' list, all of which are empty except for the profile i saved...
|
Sajin
EVGA Forum Moderator
- Total Posts : 49165
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: offline
- Ribbons : 199
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:29:01
(permalink)
Well one of the F keys should prompt you to load optimized defaults. Try F5.
|
redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:39:53
(permalink)
It's F5... loading optimized defaults and resetting has me stuck at post code 00....
|
redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:44:23
(permalink)
Going back and reloading the light OC profile per above, save/reset and boot back into OS fine. At this point, here's what's happening consistently (i) if i shut down PC, on reboot it will get stuck at post code 10 and (ii) when i CMOS reset, i can reload the same OC profile and boot in without issue and use PC without issue, as long as i don't repeat step (i) (which is shut down my PC, as in overnight or whatever)....
|
Sajin
EVGA Forum Moderator
- Total Posts : 49165
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: offline
- Ribbons : 199
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:51:20
(permalink)
If this issue didn’t occur on an older bios I would revert to an older one.
|
redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:52:36
(permalink)
It did, that caused me to check for an update and load 2.01. So this was happening on the old bios and is happening on the new bios.
|
Sajin
EVGA Forum Moderator
- Total Posts : 49165
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: offline
- Ribbons : 199
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/14 08:56:37
(permalink)
|
redrockt990
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2019/01/07 11:18:32
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/16 06:51:17
(permalink)
I appreciate the thoughts, but wouldn't the fact that this is an issue only on boot from cold/off (i.e., i can cmos reset, load my profile and boot without issue, everytime) suggest a more narrow issue than the mob being bad? Just seems like tossing the baby out with the bath water...
|
Sajin
EVGA Forum Moderator
- Total Posts : 49165
- Reward points : 0
- Joined: 2010/06/07 21:11:51
- Location: Texas, USA.
- Status: offline
- Ribbons : 199
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/16 08:58:53
(permalink)
Feel free to keep using you’re workaround. 00 on cold start shouldn’t be happening at default settings. Maybe you should call evga tech support to see what they suggest.
|
rjohnson11
EVGA Forum Moderator
- Total Posts : 102260
- Reward points : 0
- Joined: 2004/10/05 12:44:35
- Location: Netherlands
- Status: offline
- Ribbons : 84
Re: POST CODE 10 loop (z490 Kingpin Dark)
2021/08/16 09:09:43
(permalink)
Doesn't the Z490 Kingpin Dark have 3 BIOs? Did you try all three?
|
mmomega
New Member
- Total Posts : 64
- Reward points : 0
- Joined: 2016/02/22 06:09:47
- Status: offline
- Ribbons : 0
Re: POST CODE 10 loop (z490 Kingpin Dark)
2022/06/29 07:44:32
(permalink)
Did this ever get resolved? I am having the same issue on the z690. 00 from cold start.
DAD-EVGA Z790 Dark KP: 13900KS: 64GB 8000: dual 2TB 990 Pro: Gigabyte 4090 w/ 1000w Bios: Seasonic 1600w Prime Titanium 3-360rad fat boys + EK DirectDie SON-Asus Strix b550i: AMD 5900X: 32GB 3600C16: dual 1TB WD nvme: evga 3080Ti: sfx750 psu: 2-360rad + optimus block +optimus gpu block+ ek pump/res +16mm hardlined WIFE-Asus x670e Creator: AMD7950X: 64GB 6000: 1TB nvme: evga K|NGP|N 3090: Seasonic 1000w Prime Titanium psu : 3-360rad + ek block + ek distroblock/pump
|