ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
While putting my system back together today threads in one of the mounting holes on radiator of my 2080 Super FTW3 Hybrid got completely stripped (not threads on the screw but inside the hole). I was using screws supplied with the card, I was always very careful not to crossthread nor overtighten, card was mounted less than a dozen of times yet threads in that hole got stripped completely clean off so now my radiator is attached to the case with only three screws. To me that implies metal used for radiator is soft (or at least softer enough than screws) and couldn’t withstand being (re)mounted more than few times, as if manufacturer didn’t design/test them for being mounted more than few times. So buyer beware when (re)assembling systems with Hybrid cards, you might end up with damage to them just through what should be normal no issue activity and they are extremely expensive and practically impossible to replace/fix nowadays.
|
rjohnson11
EVGA Forum Moderator
- Total Posts : 102251
- Reward points : 0
- Joined: 2004/10/05 12:44:35
- Location: Netherlands
- Status: online
- Ribbons : 84
Re: Owner/Buyer Beware: Hybrid Kits
2021/04/08 01:11:15
(permalink)
All I can advise you to do is to contact EVGA tech support
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/04/08 01:35:20
(permalink)
rjohnson11 All I can advise you to do is to contact EVGA tech support
I will. But I still wanted to post this for benefit of others.
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/04/08 22:12:21
(permalink)
To those that are interested: Earlier today I checked radiator mounting area and then screw itself with a magnet. Mounting area is non-magnetic while screw is magnetic indicating mount is, as suspected, aluminum while screw is most likely steel. Use coarse thread steel screw on hole in relatively thin aluminum and what’s the worst thing that can happen, right? In my opinion result is exactly what could’ve been easily expected.
|
bonzogoatslayer
New Member
- Total Posts : 59
- Reward points : 0
- Joined: 2021/02/02 09:54:14
- Status: offline
- Ribbons : 0
Re: Owner/Buyer Beware: Hybrid Kits
2021/04/30 07:14:59
(permalink)
Radiators are usually made out of aluminum. It's odd that they wouldn't use brass studs for the screws though, even molded plastic studs wouldn't strip out as easy as aluminum. Just saying, JB Weld isn't conductive ;)
08G-P5-3797-KL 6/10/2021 6:37:55 AM PT YES12G-P5-3967-KR 6/3/2021 8:14:09 AM PT YES12G-P5-3968-KR 6/3/2021 8:01:54 AM PT No 10G-P5-3888-KR 12/14/2020 7:56:20 AM PT No 10G-P5-3895-KR 10/15/2020 10:43:59 AM PT No 10G-P5-3897-KR 10/6/2020 10:23:34 AM PT YES
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/04/30 10:02:43
(permalink)
bonzogoatslayer Radiators are usually made out of aluminum. It's odd that they wouldn't use brass studs for the screws though, even molded plastic studs wouldn't strip out as easy as aluminum.
Yes, aluminum is what is used for heat transfer/dissipation but just like you and I are pointing out mounting points do not have to be made from aluminum. Just like they aren't in many car industry radiators that are also made from aluminum even though car radiators don't get (re)mounted as many times as AIOs do. bonzogoatslayer Just saying, JB Weld isn't conductive ;)
That is one of the options I've looked at, it is just that doesn't work well on smaller holes. In any case I believe one shouldn't even have to be at this point.
|
deguinan
New Member
- Total Posts : 3
- Reward points : 0
- Joined: 2021/05/02 18:07:09
- Status: offline
- Ribbons : 0
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/02 18:51:58
(permalink)
Do these things work with the 3090 Hydro Copper?
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/02 20:09:38
(permalink)
deguinan Do these things work with the 3090 Hydro Copper?
Hydro Copper is a completely different thing.
|
lejeunedillon92
Superclocked Member
- Total Posts : 102
- Reward points : 0
- Joined: 2020/10/25 21:37:36
- Status: offline
- Ribbons : 0
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/02 23:13:23
(permalink)
It's stuff like this that makes me paranoid of AIOs
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/03 09:54:39
(permalink)
lejeunedillon92 It's stuff like this that makes me paranoid of AIOs
They have their cons and they have their pros, I believe they do have their place in the world and some of cons are avoidable by manufacturer.
|
jimbopoppins
Superclocked Member
- Total Posts : 103
- Reward points : 0
- Joined: 2017/10/25 16:44:47
- Status: offline
- Ribbons : 0
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/19 12:04:02
(permalink)
Thanks for the cautionary tale. Is there a recommended tightening specification.. like a torque wrench or something, or is it all just by feeel?
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/19 15:45:12
(permalink)
jimbopoppins Thanks for the cautionary tale. Is there a recommended tightening specification.. like a torque wrench or something, or is it all just by feeel?
I'm not aware of any AIO manufacturer, including EVGA, giving recommended torque specs, it is all by feel. In my case I suspect it wasn't the tightness that caused the issue but the imperfection on that particular screw's and/or hole's thread. I've been careful to not make it more than finger tight, nor cross thread it, and out of 8 holes (I have two cards) "only" one of them ended up stripped smooth, remaining 7 are fine.
|
HeavyHemi
Insert Custom Title Here
- Total Posts : 15665
- Reward points : 0
- Joined: 2008/11/28 20:31:42
- Location: Western Washington
- Status: offline
- Ribbons : 135
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/19 16:12:22
(permalink)
Captive nuts are your solution. EVGA does not make AIO's they are farmed out to ASETEK just like almost everyone else does. The frame is made of aluminum using standard threads with standard, not coarse pitch machine screws. It's a bummer you stripped out a hole. Use a cap nut to fix it. You might notice you're not getting a huge amount of traffic with folks having your issue. That's because it's not really an issue. Literally billions of attachments and you can expect a few QA escapes. Your other 7 holes should last until you're no long using the product. I don't see the issue and neither (with the lack of traffic) does pretty much anyone else. jimbopoppins Thanks for the cautionary tale. Is there a recommended tightening specification.. like a torque wrench or something, or is it all just by feeel?
If you're using a small hand screw driver, you don't need a torque spec. Spin down finger tight then 1/4 past and you should never have an issue. bonzogoatslayer Radiators are usually made out of aluminum. It's odd that they wouldn't use brass studs for the screws though, even molded plastic studs wouldn't strip out as easy as aluminum. Just saying, JB Weld isn't conductive ;)
Not odd at all, that would add a huge cost to manufacturing.
post edited by HeavyHemi - 2021/05/19 16:15:12
EVGA X99 FTWK / i7 6850K @ 4.5ghz / RTX 3080Ti FTW Ultra / 32GB Corsair LPX 3600mhz / Samsung 850Pro 256GB / Be Quiet BN516 Straight Power 12-1000w 80 Plus Platinum / Window 10 Pro
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/19 16:23:41
(permalink)
HeavyHemi If you're using a small hand screw driver, you don't need a torque spec. Spin down finger tight then 1/4 past and you should never have an issue.
IMHO "never" is too strong of a statement and "usually you shouldn't have an issue" would be better fit. I obviously did have an issue even though I was careful to finger tighten and not even go 1/4 past so "never say never".
|
HeavyHemi
Insert Custom Title Here
- Total Posts : 15665
- Reward points : 0
- Joined: 2008/11/28 20:31:42
- Location: Western Washington
- Status: offline
- Ribbons : 135
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/19 21:19:50
(permalink)
ZoranC
HeavyHemi If you're using a small hand screw driver, you don't need a torque spec. Spin down finger tight then 1/4 past and you should never have an issue.
IMHO "never" is too strong of a statement and "usually you shouldn't have an issue" would be better fit. I obviously did have an issue even though I was careful to finger tighten and not even go 1/4 past so "never say never".
+ You missed the word should which serves functionally the same as usually. Further you ignore the point that EVGA is simply using the same manufacture and the same materials as everyone else. You're missing the point that your argument should apply to pretty much every single one of these made. Oddly very few have issues. So is the issue manufacturing or the user? I'm not sure why you're intent on repeating your same flawed arguments.
EVGA X99 FTWK / i7 6850K @ 4.5ghz / RTX 3080Ti FTW Ultra / 32GB Corsair LPX 3600mhz / Samsung 850Pro 256GB / Be Quiet BN516 Straight Power 12-1000w 80 Plus Platinum / Window 10 Pro
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/19 22:16:45
(permalink)
HeavyHemi You missed the word should which serves functionally the same as usually.
In my understanding of English “should never” means literally that, “if you do it this way you will never have an issue”. While it is still possible to do it that way and yet end up with issue. HeavyHemi Further you ignore the point that EVGA is simply using the same manufacture and the same materials as everyone else. You're missing the point that your argument should apply to pretty much every single one of these made.
Where exactly did I say this is potential issue with -only- EVGA and wouldn’t be an issue with any radiator manufactured in same way under same circumstances? I didn’t. It goes without saying, a common sense, that it goes for every single one using such approach. HeavyHemi Oddly very few have issues.
You have documentation with statistics to show? HeavyHemi So is the issue manufacturing or the user?
Are you claiming that if -you- tried to use steel screw that doesn’t fit aluminum hole right laws of physical world would magically no longer apply and no damage would ever get incurred to that hole? Don’t tell me it wouldn’t. It happens all the time to even most experienced mechanics in various industries whenever hole is in soft metal. Anybody that has, for example, worked on bikes or cars can tell you it happens often enough due to no fault of the user. That is one of reasons behind HeliCoil existing. BTW, I just did Google for “AIO stripped thread” and quite a few results came back. They all must be user error, right? But guess what, let’s for a second pretend they all -are- user error. As an engineer I’ve been taught that if something gets damaged by user error often enough that is a sign of a design that is too easily damaged and thus not good enough. Yeah, more error tolerant design might cost more but how much more would it really cost? Do you think those that are paying from several hundred to few thousand $ for water cooled card would be really complaining if that drove cost $5, or even $20, up? HeavyHemi I'm not sure why you're intent on repeating your same flawed arguments.
… and I’m not sure why you are intent on jumping to conclusions and making statements -about something that you were not present for to witness-, and keep repeating that, but based on pattern of your posts whenever I discuss some issue one might get an impression you are for whatever reason just bent on dogging me.
post edited by ZoranC - 2021/05/20 00:14:51
|
Cool GTX
EVGA Forum Moderator
- Total Posts : 30974
- Reward points : 0
- Joined: 2010/12/12 14:22:25
- Location: Folding for the Greater Good
- Status: offline
- Ribbons : 122
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/20 09:43:24
(permalink)
Not much material & aluminum at that ... I use one finger & my thumb on the side of the driver - to gently tighten fans to radiators - & stop when any resistance is felt
|
transdogmifier
CLASSIFIED ULTRA Member
- Total Posts : 6116
- Reward points : 0
- Joined: 2003/09/05 14:26:21
- Location: Orlando, Fl
- Status: offline
- Ribbons : 17
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/20 09:55:01
(permalink)
ZoranC
HeavyHemi You missed the word should which serves functionally the same as usually.
In my understanding of English “should never” means literally that, “if you do it this way you will never have an issue”. While it is still possible to do it that way and yet end up with issue.
I think that's an interpretation regarding each individual and easier to catch if it's verbally stated rather than type written, as you can't get the intonation and understanding....he might have put "SHOULD" in caps an italics to better convey what he meant, but functionally he can be correct (and incorrect) at the same time.
post edited by transdogmifier - 2021/05/20 09:57:44
AMD Ryzen 7900x3d Deepcool LT720 Gigabyte Aorus Elite AX X670 (Might change..don't like this board) eVGA GeForce RTX 3090 FTW3 Ultra Gaming (Hybrid kit on it) Asus ROG Swift PG43UQ 4k Monitor eVGA 1600W Supernova T2 PSU 32GB Kingston 6000 DDR5 (2x16GB) Fury Corsair MP600 Pro 2TB (Boot) Corsair MP600 2TB (Games/Data) Phanteks P500A Case
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/20 10:17:06
(permalink)
Cool GTX Not much material & aluminum at that ... I use one finger & my thumb on the side of the driver - to gently tighten fans to radiators - & stop when any resistance is felt
That is exactly how I do it yet I ended up with damage on this particular hole. I am guessing when match between threads on screw and hole isn't good and hole material is much softer than screw every time you screw/unscrew you keep reshaping thread in the hole, "grinding" away some of the material without feeling any resistance, until eventually thread in the hole is practically gone / there isn't enough left to keep screw in place.
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/20 10:29:48
(permalink)
transdogmifier
ZoranC
HeavyHemi You missed the word should which serves functionally the same as usually.
In my understanding of English “should never” means literally that, “if you do it this way you will never have an issue”. While it is still possible to do it that way and yet end up with issue.
I think that's an interpretation regarding each individual and easier to catch if it's verbally stated rather than type written, as you can't get the intonation and understanding....he might have put "SHOULD" in caps an italics to better convey what he meant, but functionally he can be correct (and incorrect) at the same time.
Granted any word, whether written or spoken, can be misinterpreted so when rule of thumb I follow when speaking / interpreting is that meaning meant is one vast majority of people use those words in, I don't look for hidden meanings cause there might be 0.01% probability someone expresses themselves differently than rest of the world. So if vast majority of people interprets meaning of “should never” as “if you do it this way you will never have an issue” then that is how I too interpret what was meant when it was said.
|
transdogmifier
CLASSIFIED ULTRA Member
- Total Posts : 6116
- Reward points : 0
- Joined: 2003/09/05 14:26:21
- Location: Orlando, Fl
- Status: offline
- Ribbons : 17
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/20 10:39:53
(permalink)
ZoranC
transdogmifier
ZoranC
HeavyHemi You missed the word should which serves functionally the same as usually.
In my understanding of English “should never” means literally that, “if you do it this way you will never have an issue”. While it is still possible to do it that way and yet end up with issue.
I think that's an interpretation regarding each individual and easier to catch if it's verbally stated rather than type written, as you can't get the intonation and understanding....he might have put "SHOULD" in caps an italics to better convey what he meant, but functionally he can be correct (and incorrect) at the same time.
Granted any word, whether written or spoken, can be misinterpreted so when rule of thumb I follow when speaking / interpreting is that meaning meant is one vast majority of people use those words in, I don't look for hidden meanings cause there might be 0.01% probability someone expresses themselves differently than rest of the world. So if vast majority of people interprets meaning of “should never” as “if you do it this way you will never have an issue” then that is how I too interpret what was meant when it was said.
It wasn't my intention to say you were wrong to interpret it the way you did..merely to say that he probably didn't mean it like that. Context is lost in many situations...and so is meaning without verbal cues. Having seen Heavy around a lot on the forums over the last ....oh..1.5 decades or so, he's a good guy and knows his stuff....So I suppose I know his 'meanings' a bit better? I don't know. Anyways, wasn't meaning to cause consternation here. I do that often enough on purpose in other places.
AMD Ryzen 7900x3d Deepcool LT720 Gigabyte Aorus Elite AX X670 (Might change..don't like this board) eVGA GeForce RTX 3090 FTW3 Ultra Gaming (Hybrid kit on it) Asus ROG Swift PG43UQ 4k Monitor eVGA 1600W Supernova T2 PSU 32GB Kingston 6000 DDR5 (2x16GB) Fury Corsair MP600 Pro 2TB (Boot) Corsair MP600 2TB (Games/Data) Phanteks P500A Case
|
ZoranC
FTW Member
- Total Posts : 1099
- Reward points : 0
- Joined: 2011/05/24 17:22:15
- Status: offline
- Ribbons : 16
Re: Owner/Buyer Beware: Hybrid Kits
2021/05/20 10:55:17
(permalink)
transdogmifier It wasn't my intention to say you were wrong to interpret it the way you did...
I didn't take your post as you saying I was wrong in my interpretation :) and my reply to you is just to explain how I reason when I interpret something. transdogmifier ... merely to say that he probably didn't mean it like that.
See, that is where we differ in how we interpret things. When vast majority of people interprets certain phrase in same way then there is no reason for me to think someone else -probably- meant it completely opposite. transdogmifier Having seen Heavy around a lot on the forums over the last ....oh..1.5 decades or so, he's a good guy and knows his stuff...
I don't know Heavy outside the context of posts addressed to me and I form impression of someone based on how they behave when interacting with -me-. transdogmifier Anyways, wasn't meaning to cause consternation here.
You didn't cause it :)
|