EVGA

EVGA Nu Audio Pro Op Amp Burson V6 Assembly

Author
Post
Essentials Only Full Version
belmont1
New Member
  • Total Posts : 8
  • Reward points : 0
  • Joined: 2019/01/14 08:05:52
  • Status: offline
  • Ribbons : 0
2020/02/15 01:48:55 (permalink)
Hello there,
i ordered my EVGA Nu Audio Pro 7.1 and removed the the Cooling Backplate and the shroud. Then i swapped the Op Amp and installed Burson V6 Vivid but i cant mount the backplate or shroud so is there danger of burning? Because the Backplate had some thermal pads. How i can attache the backplate? the backplate can only be installed with the shroud due to screw threads. Can anybody help?
thanks
#1

7 Replies Related Threads
    belmont1
    New Member
    • Total Posts : 8
    • Reward points : 0
    • Joined: 2019/01/14 08:05:52
    • Status: offline
    • Ribbons : 0
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2020/02/16 09:39:48 (permalink)
    Nobody can help me? I neef some advice
    #2
    Traaaaan
    New Member
    • Total Posts : 14
    • Reward points : 0
    • Joined: 2019/08/12 12:36:12
    • Status: offline
    • Ribbons : 0
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2021/02/03 10:49:23 (permalink)
    I'm about to do the same upgrade. I'm thinking of getting heat sinks and putting them on the chips.
    #3
    BizSAR
    EGC Lead Admin / EVGA Forum Moderator
    • Total Posts : 1712
    • Reward points : 0
    • Joined: 2007/07/13 00:27:46
    • Location: Oregon, USA
    • Status: offline
    • Ribbons : 0
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2021/02/03 11:19:42 (permalink)
    Hi!
    I think you would be best served by contacting EVGA directly with your question. Once you have registered your card, you can ask a question about it (opening a ticket) here. 
     

    BizSAR
    EVGA 3090Ti FTW3 Ultra / ZOTAC 4070Ti Trinity OC - ASUS ROG PG279QM
    #4
    EVGA_Lee
    Moderator
    • Total Posts : 4247
    • Reward points : 0
    • Joined: 2016/11/04 14:43:35
    • Location: Brea, CA
    • Status: offline
    • Ribbons : 14
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2021/02/10 19:09:37 (permalink)
    Sorry for the late reply.  Although the shroud does bleed off a bit of extra heat, the audio card will still dissipate enough heat through its heatsink to keep it safe.  The temperature tolerances on the components are much higher than you need to worry about in the system.  If you're still worried about the temps, you can always direct a little airflow in its direction.
    #5
    A123A
    New Member
    • Total Posts : 20
    • Reward points : 0
    • Joined: 2019/02/26 22:02:14
    • Status: offline
    • Ribbons : 1
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2021/02/11 19:57:32 (permalink)
    Take precise measurements of the V6 dimensions and cut/dremel the shape into the heat shield and then insert the V6 through the hole.
     
    Very simple job.
    #6
    cyber44030
    New Member
    • Total Posts : 56
    • Reward points : 0
    • Joined: 2020/02/20 00:36:02
    • Status: offline
    • Ribbons : 3
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2021/02/26 12:09:11 (permalink)
    I have been using two Burson Classics V6 for about a year now and have had no issues with heat or the card in general. Everything will be alright.
    #7
    cyber44030
    New Member
    • Total Posts : 56
    • Reward points : 0
    • Joined: 2020/02/20 00:36:02
    • Status: offline
    • Ribbons : 3
    Re: EVGA Nu Audio Pro Op Amp Burson V6 Assembly 2021/02/26 12:11:17 (permalink)
    A123A
    Take precise measurements of the V6 dimensions and cut/dremel the shape into the heat shield and then insert the V6 through the hole.
     
    Very simple job.


    Why do all that when you can just leave the back shroud off when you swap the op amps. Burson also sells flexable extension connectors.
    #8
    Jump to:
  • Back to Mobile