EVGA

Part # needed for GTX 970 re-solder

Author
Post
Essentials Only Full Version
SM-71
iCX Member
  • Total Posts : 292
  • Reward points : 0
  • Joined: 2010/08/26 09:51:54
  • Status: offline
  • Ribbons : 8
2019/07/20 18:31:35 (permalink)
I know this is a long shot, but had a chip blow out on my EVGA 970 card - EVGA part # 04G-P4-2978-KR - can anyone from EVGA provide me with part numbers???   Card is 9 months out of warranty, and I can do the repair myself if I get the right replacement parts. 
 
The chip in question is the light grey chip just right of the chip at c233 seen below.   I may also need the part numbers for the chip at c233, and the small black one just above the blown chip.
 
 
 

Rebuild 2.0 Specs:  Phantek's Enthoo Pro Full Tower case * Gigabyte Z690 Gaming X DDR4 motherboard * Intel i9-13900KS CPU with Kraken X63 AIO * WIN 11 PRO 64bit * MSI 4070 Ti Gaming X Trio GPU * Corsair Vengeance 64GB(4x16GB) RAM * Solidigm P44 Pro 2TB M.2 NVMe SSD (Win11 Pro) + Intel 665p 1TB M.2 NVMe (storage) + Samsung 990 Pro 2TB M.2 NVMe (storage) + Samsung 980 1TB M.2 NVMe (Ubuntu) * Seasonic Vertex GX-1200 1200W ATX 3.0 PSU * Samsung 50 inch QN90A 4K TV/monitor * FANS: Bitfenix Spectre Pro 200mm front intake + 2x Noctua NF-A14 Industrial PPC 140mm exhaust on Kraken X63 radiator + 1 Noctua NF-A12 120mm rear intake
#1

2 Replies Related Threads
    bcavnaugh
    The Crunchinator
    • Total Posts : 38977
    • Reward points : 0
    • Joined: 2012/09/18 17:31:18
    • Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
    • Status: offline
    • Ribbons : 282
    Re: Part # needed for GTX 970 re-solder 2019/07/20 19:27:26 (permalink)
    If you cannot get this fixed PM about a GTX 980 Hydro Copper Card, Yes you would have to create a Water Loop for it.
    The only cards I have on Air is the GTX 690 and GTX 780.
    post edited by bcavnaugh - 2019/07/20 19:30:37

    Associate Code: 9E88QK5L7811G3H


     
    #2
    SM-71
    iCX Member
    • Total Posts : 292
    • Reward points : 0
    • Joined: 2010/08/26 09:51:54
    • Status: offline
    • Ribbons : 8
    Re: Part # needed for GTX 970 re-solder 2019/07/26 13:50:11 (permalink)
    bcavnaugh
    If you cannot get this fixed PM about a GTX 980 Hydro Copper Card, Yes you would have to create a Water Loop for it.
    The only cards I have on Air is the GTX 690 and GTX 780.

    Thanks for the offer, but save it for someone more in need 
     
    I don't run water loops anyway, just an off-the-shelf all-in-one water cooler.  If I could afford to go the custom loop route, I would just get a 2070 instead of the 1660.
     
    EVGA tech support was no help on part #'s, so I may be out of luck  unless I find a dead one listed on ebay for dirt cheap...

    Rebuild 2.0 Specs:  Phantek's Enthoo Pro Full Tower case * Gigabyte Z690 Gaming X DDR4 motherboard * Intel i9-13900KS CPU with Kraken X63 AIO * WIN 11 PRO 64bit * MSI 4070 Ti Gaming X Trio GPU * Corsair Vengeance 64GB(4x16GB) RAM * Solidigm P44 Pro 2TB M.2 NVMe SSD (Win11 Pro) + Intel 665p 1TB M.2 NVMe (storage) + Samsung 990 Pro 2TB M.2 NVMe (storage) + Samsung 980 1TB M.2 NVMe (Ubuntu) * Seasonic Vertex GX-1200 1200W ATX 3.0 PSU * Samsung 50 inch QN90A 4K TV/monitor * FANS: Bitfenix Spectre Pro 200mm front intake + 2x Noctua NF-A14 Industrial PPC 140mm exhaust on Kraken X63 radiator + 1 Noctua NF-A12 120mm rear intake
    #3
    Jump to:
  • Back to Mobile