EVGA

PX1 iCX LED stuck on green.

Author
Post
Essentials Only Full Version
Graphite8five
SSC Member
  • Total Posts : 660
  • Reward points : 0
  • Joined: 2016/08/04 22:27:09
  • Status: offline
  • Ribbons : 3
2019/01/24 23:21:14 (permalink)
One of my iCX sensor LED's on my 1080 Ti FTW3 is stuck on green, the GPU LED to be exact. The MEM and PWR are normal blue. I can't even find where to control what these LED's do in PX1, where do I look?


 
Maximus XI Hero, 8700K 5Ghz delid, EKWB Custom loop ,Dominator RGB 3400Mhz 16GB, EVGA 2080 Ti FTW3 EK Vector, Seasonic Prime Platinum 1300W, Asus PG349Q 34" 120hz G-Sync, Phanteks Eclipse P600S. 
#1

5 Replies Related Threads
    _AlanT
    Superclocked Member
    • Total Posts : 226
    • Reward points : 0
    • Joined: 2017/07/10 15:09:16
    • Status: offline
    • Ribbons : 1
    Re: PX1 iCX LED stuck on green. 2019/01/27 00:06:01 (permalink)
    Hi Graphite8five,
     
    The G, P, M LEDs are not controllable. They are temperature LEDs.  Blue = Cool temps, Green, Fair temps, Red = High temps. Flashing Red is also not a good sign. I hope this helps!
     
    Regards,
    Alan
    EVGA
    #2
    Graphite8five
    SSC Member
    • Total Posts : 660
    • Reward points : 0
    • Joined: 2016/08/04 22:27:09
    • Status: offline
    • Ribbons : 3
    Re: PX1 iCX LED stuck on green. 2019/01/27 00:10:40 (permalink)
    EVGATech_AlanT
    Hi Graphite8five,
     
    The G, P, M LEDs are not controllable. They are temperature LEDs.  Blue = Cool temps, Green, Fair temps, Red = High temps. Flashing Red is also not a good sign. I hope this helps!
     
    Regards,
    Alan
    EVGA




    My understanding is that the LEDs turn green above 60C. Right now my G LED is green while the card is idling at 30C. The P and M LEDs are both blue but the green G LED at 30C doesn't seem right...


     
    Maximus XI Hero, 8700K 5Ghz delid, EKWB Custom loop ,Dominator RGB 3400Mhz 16GB, EVGA 2080 Ti FTW3 EK Vector, Seasonic Prime Platinum 1300W, Asus PG349Q 34" 120hz G-Sync, Phanteks Eclipse P600S. 
    #3
    NELSONTHE2ND
    New Member
    • Total Posts : 44
    • Reward points : 0
    • Joined: 2010/10/28 15:20:18
    • Status: offline
    • Ribbons : 0
    Re: PX1 iCX LED stuck on green. 2019/02/02 09:38:11 (permalink)
    My Evga GTX 1080TI FTW 3 was doing the same thing and I turned off the Evga LED Sync. It working properly now.


    #4
    Graphite8five
    SSC Member
    • Total Posts : 660
    • Reward points : 0
    • Joined: 2016/08/04 22:27:09
    • Status: offline
    • Ribbons : 3
    Re: PX1 iCX LED stuck on green. 2019/02/03 03:10:27 (permalink)
    NELSONTHE2ND
    My Evga GTX 1080TI FTW 3 was doing the same thing and I turned off the Evga LED Sync. It working properly now.




    I clicked a whole lot of buttons in the LED section of PX1 and manged to un-stick the green LED. I do not understand the LED Sync button in PX1, it does nothing at all when I turn it on. In PXOC it would open a separate LED Sync control panel. Is PX1 supposed to open a similar separate LED Sync window/control panel?


     
    Maximus XI Hero, 8700K 5Ghz delid, EKWB Custom loop ,Dominator RGB 3400Mhz 16GB, EVGA 2080 Ti FTW3 EK Vector, Seasonic Prime Platinum 1300W, Asus PG349Q 34" 120hz G-Sync, Phanteks Eclipse P600S. 
    #5
    NELSONTHE2ND
    New Member
    • Total Posts : 44
    • Reward points : 0
    • Joined: 2010/10/28 15:20:18
    • Status: offline
    • Ribbons : 0
    Re: PX1 iCX LED stuck on green. 2019/02/04 04:48:16 (permalink)
    Graphite8five
    NELSONTHE2ND
    My Evga GTX 1080TI FTW 3 was doing the same thing and I turned off the Evga LED Sync. It working properly now.




    I clicked a whole lot of buttons in the LED section of PX1 and manged to un-stick the green LED. I do not understand the LED Sync button in PX1, it does nothing at all when I turn it on. In PXOC it would open a separate LED Sync control panel. Is PX1 supposed to open a similar separate LED Sync window/control panel?


    I've uninstalled EVGA's software. It is horrible. I recommend Afterburner.
     

    post edited by NELSONTHE2ND - 2019/02/09 09:35:43


    #6
    Jump to:
  • Back to Mobile