EVGA

Precision X1 not saving scanned curve?

Author
Post
Essentials Only Full Version
striker890
New Member
  • Total Posts : 95
  • Reward points : 0
  • Joined: 2016/03/09 09:33:36
  • Status: offline
  • Ribbons : 0
2018/10/16 07:55:02 (permalink)
Just tried Precision X1 Scanner to oc my RTX 2080 TI FTW3 card and see how well the tool works. Everything went well and it scored +145 @ 110% power target. I ran Time Spy and scored an 8.6% performance increase. Not bad.
Though while changing some more settings and than playing a game the frequency curve went back to default. Though Scanner tool still shows last "score". I also saved the profile, but if I load it, it's gone.
 
Is that a bug or user error? 
#1

7 Replies Related Threads
    bcavnaugh
    The Crunchinator
    • Total Posts : 38977
    • Reward points : 0
    • Joined: 2012/09/18 17:31:18
    • Location: USA Affiliate E5L3CTGE12 Associate 9E88QK5L7811G3H
    • Status: offline
    • Ribbons : 282
    Re: Precision X1 not saving scanned curve? 2018/10/16 08:10:05 (permalink)
    Are you Running Version 0.3.2 BETA?

    Associate Code: 9E88QK5L7811G3H


     
    #2
    striker890
    New Member
    • Total Posts : 95
    • Reward points : 0
    • Joined: 2016/03/09 09:33:36
    • Status: offline
    • Ribbons : 0
    Re: Precision X1 not saving scanned curve? 2018/10/16 10:30:59 (permalink)
    bcavnaugh
    Are you Running Version 0.3.2 BETA?


    yes
    #3
    Cool GTX
    EVGA Forum Moderator
    • Total Posts : 30996
    • Reward points : 0
    • Joined: 2010/12/12 14:22:25
    • Location: Folding for the Greater Good
    • Status: offline
    • Ribbons : 122
    Re: Precision X1 not saving scanned curve? 2018/10/16 11:14:55 (permalink)
    Did you use the "Load button" to load the saved profile ?
     
    I'm on the older Beta V0.2.9.0 currently - launch last saved Profile on Boot is working for me; but I'm using manual OC settings


     
    After you save a profile, to be sure it is actually saved -- close X1, then relaunch and see if it stuck
     
    Steps
     - select the "Profile Number" (left mouse button) (right click clears the setting)
     - Load button
     - Apply button ? - can't remember if this was also needed to "recall previous profile" its been about a week since I had adjusted mine
     

    Learn your way around the EVGA Forums, Rules & limits on new accounts Ultimate Self-Starter Thread For New Members

    I am a Volunteer Moderator - not an EVGA employee

     https://foldingathome.org -->become a citizen scientist and contribute your compute power to help fight global health threats

    RTX Project EVGA X99 FTWK Nibbler EVGA X99 Classified EVGA 3080Ti FTW3 Ultra


    #4
    Cool GTX
    EVGA Forum Moderator
    • Total Posts : 30996
    • Reward points : 0
    • Joined: 2010/12/12 14:22:25
    • Location: Folding for the Greater Good
    • Status: offline
    • Ribbons : 122
    Re: Precision X1 not saving scanned curve? 2018/10/17 09:36:14 (permalink)
    @ striker890

    Update ?

    Learn your way around the EVGA Forums, Rules & limits on new accounts Ultimate Self-Starter Thread For New Members

    I am a Volunteer Moderator - not an EVGA employee

     https://foldingathome.org -->become a citizen scientist and contribute your compute power to help fight global health threats

    RTX Project EVGA X99 FTWK Nibbler EVGA X99 Classified EVGA 3080Ti FTW3 Ultra


    #5
    ealwin
    New Member
    • Total Posts : 1
    • Reward points : 0
    • Joined: 2018/12/03 21:06:11
    • Status: offline
    • Ribbons : 0
    Re: Precision X1 not saving scanned curve? 2019/01/27 00:37:48 (permalink)
    I bet you it was the load button for him.  I had the same issue until I read this thread.  Maybe Evga could move the load button above the preset numbers to make it more obvious that the two correlate.  
    #6
    d.burnette
    CLASSIFIED ULTRA Member
    • Total Posts : 5496
    • Reward points : 0
    • Joined: 2007/03/08 13:19:32
    • Status: offline
    • Ribbons : 17
    Re: Precision X1 not saving scanned curve? 2019/01/27 05:16:25 (permalink)
    ealwin
    I bet you it was the load button for him.  I had the same issue until I read this thread.  Maybe Evga could move the load button above the preset numbers to make it more obvious that the two correlate.  


    Not a bad idea at all.

    Don 
     
     
    EVGA Z390 Dark MB | i9 9900k CPU @ 5.2 GHz all cores | EVGA RTX 3090 FTW3 Ultra | 32 GB G Skill Trident Z 3200 MHz CL14 DDR4 Ram | Corsair H150i Pro Cooler | EVGA T2 Titanium 1000w Power Supply | Samsung 970 Pro 1TB m.2 Nvme | Samsung 970 Evo 1TB m.2 Nvme | Samsung 860 Evo 1TB SATA SSD | EVGA DG 87 Case |
     
     
     
     
     
     
     
     
     
     
    #7
    Dascery
    New Member
    • Total Posts : 7
    • Reward points : 0
    • Joined: 2019/01/23 02:39:18
    • Status: offline
    • Ribbons : 0
    Re: Precision X1 not saving scanned curve? 2019/01/27 18:16:08 (permalink)
    Sure,it is.
    #8
    Jump to:
  • Back to Mobile