EVGA

Hot!EVGA GeForce RTX 3080 FTW3 XOC BIOS

Page: << < ..2627282930.. > >> Showing page 30 of 33
Author
AdrianK258
New Member
  • Total Posts : 23
  • Reward points : 0
  • Joined: 2020/12/21 06:54:04
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/02 07:35:29 (permalink)
Hello,
 
i installed AIO kit from EVGA on my 3080 ftw3 ultra today and I am trying to flash hybrid bios from post#1 but I am getting this and I tried to install normal and OC....
 
NVIDIA Firmware Update Utility
Version 5.670.0
Copyright (C) 2018-2020, NVIDIA Corporation. All rights reserved.

   The display may go *BLANK* on and off for up to 6 seconds
   or more during access to the EEPROM depending on your display
   adapter and output device, it will begin in about 3 seconds.

No display adapters were found that are compatible with this update.

***UPDATE***
apparently you can install FTW3 ultra bios only, not hybrid. not sure why, since right now this is hybrid card...anyway I am hitting 444W draw for the board.  +650 on mem and +148 on core. timespy graphic score 19053
post edited by AdrianK258 - 2021/03/02 08:33:27

Attached Image(s)

donnie123
New Member
  • Total Posts : 51
  • Reward points : 0
  • Joined: 2021/01/07 04:38:25
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/02 09:01:33 (permalink)
AdrianK258
Hello,
 
i installed AIO kit from EVGA on my 3080 ftw3 ultra today and I am trying to flash hybrid bios from post#1 but I am getting this and I tried to install normal and OC....
 
NVIDIA Firmware Update Utility
Version 5.670.0
Copyright (C) 2018-2020, NVIDIA Corporation. All rights reserved.

  The display may go *BLANK* on and off for up to 6 seconds
  or more during access to the EEPROM depending on your display
  adapter and output device, it will begin in about 3 seconds.

No display adapters were found that are compatible with this update.

***UPDATE***
apparently you can install FTW3 ultra bios only, not hybrid. not sure why, since right now this is hybrid card...anyway I am hitting 444W draw for the board.  +650 on mem and +148 on core. timespy graphic score 19053




Thumbs up, interesting I hit same timespy graphic score but it only draws 380 watts during the test..
AdrianK258
New Member
  • Total Posts : 23
  • Reward points : 0
  • Joined: 2020/12/21 06:54:04
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/03 00:20:08 (permalink)
donnie123
AdrianK258
Hello,
 
i installed AIO kit from EVGA on my 3080 ftw3 ultra today and I am trying to flash hybrid bios from post#1 but I am getting this and I tried to install normal and OC....
 
NVIDIA Firmware Update Utility
Version 5.670.0
Copyright (C) 2018-2020, NVIDIA Corporation. All rights reserved.

The display may go *BLANK* on and off for up to 6 seconds
or more during access to the EEPROM depending on your display
adapter and output device, it will begin in about 3 seconds.

No display adapters were found that are compatible with this update.

***UPDATE***
apparently you can install FTW3 ultra bios only, not hybrid. not sure why, since right now this is hybrid card...anyway I am hitting 444W draw for the board.  +650 on mem and +148 on core. timespy graphic score 19053




Thumbs up, interesting I hit same timespy graphic score but it only draws 380 watts during the test..


and what OC you have on yours? i am hitting 55C at max load. case is meshify c i have 2x140mm fans intake. aio is on the top as outtake and rear fan 120 outtake.
 
rahimdamji29
New Member
  • Total Posts : 80
  • Reward points : 0
  • Joined: 2020/05/28 11:36:47
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/03 07:37:53 (permalink)
For some reason or another these cards can't crash in gaming when you are overclocked..... They can't handle the power phase switching. I think it has something to do with the ****ty up9511 voltage controller.... Almost all other cards have up9512 which is wayyyyy better, has way higher frequency range. I'm really annoyed I have to downlock my card to 2115 to 2130 to stay stable in games. Keep in mind my max temps are 36 to 41c gaming on my water block
donnie123
New Member
  • Total Posts : 51
  • Reward points : 0
  • Joined: 2021/01/07 04:38:25
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/03 11:06:41 (permalink)
Again the voltage controller is not it. Otherwise other cards that don't feature it wouldn't have exactly the same symptoms. Same thing can happen on Kingpin or some strix cards, as well as handful of gigabyte.
 
Probably the boost clocks are just the silicon lottery, however you want to turn it. I can have 2130+ stable in games without any issues, while somebody else can't, same goes for CPU's somebody can have much better bin and push much higher clocks on the same cpu..
DustoMan
iCX Member
  • Total Posts : 339
  • Reward points : 0
  • Joined: 2008/07/25 07:00:31
  • Location: Sparta, WI
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/03 14:20:15 (permalink)
AdrianK258
Hello,
 
i installed AIO kit from EVGA on my 3080 ftw3 ultra today and I am trying to flash hybrid bios from post#1 but I am getting this and I tried to install normal and OC....
 
NVIDIA Firmware Update Utility
Version 5.670.0
Copyright (C) 2018-2020, NVIDIA Corporation. All rights reserved.

  The display may go *BLANK* on and off for up to 6 seconds
  or more during access to the EEPROM depending on your display
  adapter and output device, it will begin in about 3 seconds.

No display adapters were found that are compatible with this update.

***UPDATE***
apparently you can install FTW3 ultra bios only, not hybrid. not sure why, since right now this is hybrid card...anyway I am hitting 444W draw for the board.  +650 on mem and +148 on core. timespy graphic score 19053


Here's the bios to convert the card to a Hybrid card so the fans curve are correct and it shows up correct in X1.
https://forums.evga.com/FindPost/3178112

Dusto
dustoman (at) gmail (dot) com
 



Scorpio_ASC
New Member
  • Total Posts : 5
  • Reward points : 0
  • Joined: 2018/04/20 05:24:50
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/04 02:21:55 (permalink)

rahimdamji29
For some reason or another these cards can't crash in gaming when you are overclocked..... They can't handle the power phase switching. I think it has something to do with the ****ty up9511 voltage controller.... Almost all other cards have up9512 which is wayyyyy better, has way higher frequency range. I'm really annoyed I have to downlock my card to 2115 to 2130 to stay stable in games. Keep in mind my max temps are 36 to 41c gaming on my water block


I doubt the cards with up9512 are set to switch at a higher frequency, even if they are capable of it.


edit: I mean i have a FTW3 too and im game stable at 2160-2175, as dude said before, its probably just your chip thats limiting you.
post edited by Scorpio_ASC - 2021/03/04 02:24:29
kevinc313
CLASSIFIED Member
  • Total Posts : 2662
  • Reward points : 0
  • Joined: 2019/02/28 09:27:55
  • Status: offline
  • Ribbons : 16
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/04 06:40:55 (permalink)
At 4K in RDR2, I'm stable at 2,085mhz 1.081V - 2,100mhz 1.1V, 400W-420W.  That's a TOUGH load for non-RTX, so much that the prevailing opinion online is that you can't run RDR2 with an OC.  Like +90 core, +600 mem usually at about 55C, hybrid.
post edited by kevinc313 - 2021/03/04 07:40:35
third life
New Member
  • Total Posts : 3
  • Reward points : 0
  • Joined: 2021/01/26 07:52:44
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/05 14:39:19 (permalink)
rahimdamji29
Jaz11
Count yourself lucky. Mine won't draw over 390w on the 450w bios. It's ****ed

U need to get ur card colder or a waterblock. Otherwise u won't draw as much. I'm sitting at 36 to 44 max temps..... With my loop and block. 2130 to 2160 in games.... Port royal 2190 is max stable.... Timespy 2175 if I keep it under 33c.... Before I had under water max game clocks were 2085 to 2055 if I was lucky....under 60c

Umm, nope. My card is cold AF. 8-10 Celsius actually, 30-35 under full load and its not pulling more on Timespy than 398W with 1,1V and clocks set to 160 on the GPU and 1250 on the VRAM.


 
BIOS is installed, tried both switch positions, rebooted etc. nothing works for me. What is wrong with this card ? What load do i have to put on it ? I think the BIOS is not giving me **** as the 398W are no matter if i push the Voltage to 1.1V or leave it at standard 1.063 or with the VRAM at 0 OC.
 
Anyone have an idea what i could do ? Is it the Card ? Is it the BIOS ?
 
EDIT: Forget what i said. I downloaded the BIOS again, reflashed, shut down the PC, flipped the switch twice and now its working. I don't know where i messed up...argh.
post edited by third life - 2021/03/05 15:14:53
Jaz11
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2018/03/08 22:57:54
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/06 15:22:26 (permalink)
Hey. Since you say it's working are you now drawing full power limit?

I have flashed the bios twice and shut down to flip the of switch off. Booted up in non of. Shut down and flipped back to OC switch but still the same

Did you do anything different? What else should I try?
Jaz11
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2018/03/08 22:57:54
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/06 23:46:18 (permalink)
third life
rahimdamji29
Jaz11
Count yourself lucky. Mine won't draw over 390w on the 450w bios. It's ****ed

U need to get ur card colder or a waterblock. Otherwise u won't draw as much. I'm sitting at 36 to 44 max temps..... With my loop and block. 2130 to 2160 in games.... Port royal 2190 is max stable.... Timespy 2175 if I keep it under 33c.... Before I had under water max game clocks were 2085 to 2055 if I was lucky....under 60c

Umm, nope. My card is cold AF. 8-10 Celsius actually, 30-35 under full load and its not pulling more on Timespy than 398W with 1,1V and clocks set to 160 on the GPU and 1250 on the VRAM.


 
BIOS is installed, tried both switch positions, rebooted etc. nothing works for me. What is wrong with this card ? What load do i have to put on it ? I think the BIOS is not giving me **** as the 398W are no matter if i push the Voltage to 1.1V or leave it at standard 1.063 or with the VRAM at 0 OC.
 
Anyone have an idea what i could do ? Is it the Card ? Is it the BIOS ?
 
EDIT: Forget what i said. I downloaded the BIOS again, reflashed, shut down the PC, flipped the switch twice and now its working. I don't know where i messed up...argh.




 
hmm just tried this twice and didnt fix for me. still hitting 380-390w and saying power limit :(
third life
New Member
  • Total Posts : 3
  • Reward points : 0
  • Joined: 2021/01/26 07:52:44
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/07 01:36:09 (permalink)
Jaz11
Hey. Since you say it's working are you now drawing full power limit?

I have flashed the bios twice and shut down to flip the of switch off. Booted up in non of. Shut down and flipped back to OC switch but still the same

Did you do anything different? What else should I try?

Hey, yes it seems to be working as intended, drawing447-449W from the Wall. I re-downloaded the file, unpacked it, ran it as administrator.
 
I am unsure if i was in the Standard BIOS Switch position when i flashed the new OC BIOS to the OC Position or in which position it was. Maybe check that as well. Flash it to the one that is active or to the one that is inactive is the only thing that comes to my mind that you could try further.
 
Jaz11
 
hmm just tried this twice and didnt fix for me. still hitting 380-390w and saying power limit :(

You're Watercooling as well ? I used Water with 8-10 degrees Celsius and TimeSpy as Benchmark. I am not sure if you can even pull that much if you're air cooling as with high heat load it might pull back on the Voltage ?
Jaz11
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2018/03/08 22:57:54
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/07 01:48:16 (permalink)
Hmmm I didnt run it as administrator but I made sure to extract it. Made sure nothing was running in background both times. Yeh I checked the switch is on the OC bios with it flicked closest to io ports .

Yeh under waterblock as well. GPU temps in the 40s. Still won't draw over 390w :(

Not sure what else I can do.

The bios has definitely applied because gpuz says my power limit is 450w...
third life
New Member
  • Total Posts : 3
  • Reward points : 0
  • Joined: 2021/01/26 07:52:44
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/07 03:42:13 (permalink)
Jaz11
Hmmm I didnt run it as administrator but I made sure to extract it. Made sure nothing was running in background both times. Yeh I checked the switch is on the OC bios with it flicked closest to io ports .

Yeh under waterblock as well. GPU temps in the 40s. Still won't draw over 390w :(

Not sure what else I can do.

The bios has definitely applied because gpuz says my power limit is 450w...

Ah ok, my Card didn't apply the BIOS at first even though it said so, i couldn't set the Powerlimit in X1 to 118%. Can you set it to 118% ? Then it should be good to go.
 
Also you might check your cabling if you are using piggybacked cables or do you have three dedicated power cables ?
Jaz11
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2018/03/08 22:57:54
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/07 03:43:21 (permalink)
Yeh can set to 118% power limit. Yeh all separate pcie cables to 1000w psu
rahimdamji29
New Member
  • Total Posts : 80
  • Reward points : 0
  • Joined: 2020/05/28 11:36:47
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/07 17:36:22 (permalink)
Been talking to some guys with 3090 ftw3.... seems you can flash xc3 3090 bios on the 3090 ftw3....and it actually gives more power 370+150..... And they are scoring 5% higher performance because of it.... Does anyone have any thoughts on doing the xc3 bios on a 3080 ftw3??? I'm so willing to try it....
rottentreats
New Member
  • Total Posts : 21
  • Reward points : 0
  • Joined: 2011/10/07 23:54:35
  • Status: online
  • Ribbons : 2
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/08 19:04:17 (permalink)
So I have a 3080 FTW3 Ultra Hybrid coming tomorrow and am looking for advice on what to do with this BIOS business.  I'll be using my own fan curve so I'll probably just be downloading the "Normal" XOC BIOS and flashing the OC position on the card. (keeping the normal position as my fail safe stock/default option)
 
I imagine I should install the card and let PX1 update the firmware. Then do some stock benchmarking (portal royal and time spy) for baseline data so I can see what kind of gains I'm actually getting.
 
Then what would some of you recommend? Flash the Normal "EVGA GeForce RTX 3080 FTW3 HYBRID" BIOS from OP? Or just the Normal "EVGA GeForce RTX 3080 FTW3 ULTRA" BIOS?  Or nothing and maybe just wait for the next BIOS revision? (maybe even the one that will include BAR support or higher power limit) Thanks in advance I appreciate any insight, I've thought about this and read soooooo many pages and still am not sure what is the "best". <3 
 
EDIT: IT CAME AND SO DID I.  I ended up flashing the XOC Hybrid BIOS to the OC position.  I think it's running as expected and I am the happy. :D
 
post edited by rottentreats - 2021/03/09 22:37:57

Attached Image(s)


Case: Fractal Design Meshify S2 Dark Tint Tempered Glass
Mobo: ASUS ROG MAXIMUS XII HERO Z490 w/ Version 2004 Beta Version BIOS (for Resizable BAR support)
GPU: EVGA GeForce RTX 3080 FTW3 ULTRA HYBRID w/ XOC Normal BIOS (+120 core/+699 memory)
CPU: Intel Core i9-10900K 10-Core 3.7GHz @5.1GHz (1.325v Core Voltage, LLC 6) CORSAIR iCUE H150i RGB PRO XT, 360mm AIO
RAM: CORSAIR Vengeance RGB Pro 32GB (2x16GB) DDR4 3200 15-18-18-32 tRFC - 512 tRFC2 - 380 tRFC4 - 234
PSU: CORSAIR HX1000 1000W 80 PLUS PLATINUM
Storage: SAMSUNG 970 PRO M.2 2280 1TB X2 Raid 0 64K Stripe
Monitor: LG 34GP83A-B Ultragear 34in 144Hz G-SYNC Curved QHD (3440 x 1440) 1ms Nano IPS
Jaz11
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2018/03/08 22:57:54
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/09 23:19:37 (permalink)
Lucky! Using full power! I'm jealous
labview05
New Member
  • Total Posts : 1
  • Reward points : 0
  • Joined: 2020/10/26 22:08:51
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/09 23:22:21 (permalink)

post edited by labview05 - 2021/03/09 23:26:07
jamexr
iCX Member
  • Total Posts : 259
  • Reward points : 0
  • Joined: 2016/07/21 16:30:16
  • Location: SLC, Utah, USA
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/11 02:30:12 (permalink)
Jaz11
Lucky! Using full power! I'm jealous


It's not. You can see he's capped at 430w and 3rd pcie pin is not drawing much, same issue as the 3090s that has been posted before many times. Evga needs to address this already, they said update in "a few weeks" back in February.
jamexr
iCX Member
  • Total Posts : 259
  • Reward points : 0
  • Joined: 2016/07/21 16:30:16
  • Location: SLC, Utah, USA
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/11 02:45:30 (permalink)
Evga has started a replacement program for 3090s with the unbalanced power draw from pcie pins and 430w cap. My 3080 ftw has the same and many others have reported same, but no aknowlegment for us yet ..
Bcassiman
Superclocked Member
  • Total Posts : 145
  • Reward points : 0
  • Joined: 2020/09/10 18:19:50
  • Status: offline
  • Ribbons : 1
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/11 10:34:48 (permalink)
Got 4th place out of 40k results in Timespy for the 5600x/3080 combo globally with this bios. I did convert to a hybrid though. NVIDIA GeForce RTX 3080 video card benchmark result - AMD Ryzen 5 5600X,Micro-Star International Co., Ltd. MAG X570 TOMAHAWK WIFI (MS-7C84) (3dmark.com)
ParaWM
New Member
  • Total Posts : 7
  • Reward points : 0
  • Joined: 2021/01/23 08:58:50
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/12 08:14:35 (permalink)
Bcassiman
Got 4th place out of 40k results in Timespy for the 5600x/3080 combo globally with this bios. I did convert to a hybrid though. 


So you converted to Hybrid and use XOC Hybrid bios? I have FTW3 Ultra with XOC 450w bios but also capped at 400W still as many. I ran Kombustor for half an hour and see average 395W draw. PICE: 47W, 8-pin1: 129W, 8-pin2: 148W, 8-pin3: 70W. Constantly GPU-Z tells me powerlimit PerfCap reason. So is this low 8-pin3 power due to the card or due to the bios? Or is is possible PSU related? I have Fractal Design 860w platinum.
kindofabuzz
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2019/09/09 18:54:44
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/12 09:33:06 (permalink)
So will they auto update to newer versions once installed? Or do i need to check back here for updates? And are the ones linked in the first post the current versions?
rottentreats
New Member
  • Total Posts : 21
  • Reward points : 0
  • Joined: 2011/10/07 23:54:35
  • Status: online
  • Ribbons : 2
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/12 09:56:50 (permalink)
Since I am still toying with my hybrid card and seeing OC potential I spent some time today and was able to get over 118% TDP and the 450W.  Probably somehow the perfect storm.  I was just running MSI Kombustor using the (GL) msi-01 (burn-in mode) Stress test.  It wasn't stable at these speeds but got the juice it needed. Made in Taiwan serial starting with 2114 using "EVGA GeForce RTX 3080 FTW3 HYBRID - BIOS 1 (Normal)" from OP.
 
Just put +699 on the mem and +180 on the core, voltage/power sliders maxed out. Oh and 100% fans.. not sure if that mattered somehow. (maybe could have turned off the lights for more juice?) Oh well ¯\_(ツ)_/¯ since the hardware looks capable hopefully more XOC bios tweaks can do something although this issue sounds more hardware related.
 
Board Power Draw: 451.5W
PCIe Slot Power: 58.5W
8-Pin #1 Power: 143.4W
8-Pin #2 Power: 154.0W
8-Pin #3 Power: 96.8W
Power Consumption (%): 118.8 TDP
post edited by rottentreats - 2021/03/12 10:07:09

Attached Image(s)


Case: Fractal Design Meshify S2 Dark Tint Tempered Glass
Mobo: ASUS ROG MAXIMUS XII HERO Z490 w/ Version 2004 Beta Version BIOS (for Resizable BAR support)
GPU: EVGA GeForce RTX 3080 FTW3 ULTRA HYBRID w/ XOC Normal BIOS (+120 core/+699 memory)
CPU: Intel Core i9-10900K 10-Core 3.7GHz @5.1GHz (1.325v Core Voltage, LLC 6) CORSAIR iCUE H150i RGB PRO XT, 360mm AIO
RAM: CORSAIR Vengeance RGB Pro 32GB (2x16GB) DDR4 3200 15-18-18-32 tRFC - 512 tRFC2 - 380 tRFC4 - 234
PSU: CORSAIR HX1000 1000W 80 PLUS PLATINUM
Storage: SAMSUNG 970 PRO M.2 2280 1TB X2 Raid 0 64K Stripe
Monitor: LG 34GP83A-B Ultragear 34in 144Hz G-SYNC Curved QHD (3440 x 1440) 1ms Nano IPS
dam_j
New Member
  • Total Posts : 38
  • Reward points : 0
  • Joined: 2017/03/09 07:31:10
  • Location: Duesseldorf / germany
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/19 02:20:47 (permalink)
I´m gone since page 14/30.
 
Are there any news or even an answer from EVGA ?
My status is still that this "beta" bios doesn´t do anything.
 
Jaz11
New Member
  • Total Posts : 46
  • Reward points : 0
  • Joined: 2018/03/08 22:57:54
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/19 02:28:02 (permalink)
Nope. EVGA haven't done or even really aknowledged anything.

I'm still gaming seeing my "power limit" pop up from 350w...
dam_j
New Member
  • Total Posts : 38
  • Reward points : 0
  • Joined: 2017/03/09 07:31:10
  • Location: Duesseldorf / germany
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/19 02:31:42 (permalink)
Thanks!
 
This is so messed up for half a year now...
AdrianK258
New Member
  • Total Posts : 23
  • Reward points : 0
  • Joined: 2020/12/21 06:54:04
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/19 05:59:51 (permalink)
well this is my first EVGA card and most likely last. People here on the forum are excellent and helpful, but EVGA as a company lack a proper communication. There is no update for almost 6months now, I am happy that Jacob is playing DOOM Eternal but maybe provide an update here? Cards were NOT cheap and some update like: "We are working on it, ETA 3weeks" or anything like that would be nice.
dam_j
New Member
  • Total Posts : 38
  • Reward points : 0
  • Joined: 2017/03/09 07:31:10
  • Location: Duesseldorf / germany
  • Status: offline
  • Ribbons : 0
Re: EVGA GeForce RTX 3080 FTW3 (3897) XOC BIOS BETA 2021/03/19 06:08:46 (permalink)
Yeah, but he is busy answering every twitter post he´s linked to BESIDES the ones regarding this thread / this problem...
 
EVGA germany also plays dumb regarding this.
Was just asking becorse i gt my hand on another FTW3 and thoght i give it a a shot AGAIN. 
Page: << < ..2627282930.. > >> Showing page 30 of 33
Jump to:
  • Back to Mobile