hksiew
New Member
- Total Posts : 19
- Reward points : 0
- Joined: 2021/07/10 07:04:41
- Status: offline
- Ribbons : 1
Hello, does anyone knows the specifications / thickness of the thermal pads and the locations on the pcb that EVGA uses for the 3080ti ftw3? Also, after cleaning up the thermal putty, can I replace it thermal paste or thermal pads instead? It’s so difficult to look for an aftermarket thermal putty.
post edited by hksiew - 2021/08/07 00:40:39
CPU: 10900K cooled with NZXT Z73 MOBO: Z490 Aorus Xtreme GPU: EVGA 3080TI FTW3 ULTRA PSU: Seasonic Prime Gold 1300W RAM: Corsair vengeance RGB PRO 16gb x 2 Storage: Samsung 980 Pro x 2, Samsung 960 Evo Case: O11D Lianli Case fans: Lian Li AL120 Unifans x 9, Arctic F8 PWM x 2
|
KingEngineRevUp
FTW Member
- Total Posts : 1030
- Reward points : 0
- Joined: 2019/03/28 16:38:54
- Status: offline
- Ribbons : 9
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/07 01:18:40
(permalink)
|
hksiew
New Member
- Total Posts : 19
- Reward points : 0
- Joined: 2021/07/10 07:04:41
- Status: offline
- Ribbons : 1
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/07 06:33:25
(permalink)
KingEngineRevUp
Hmmm. Nothing that says anything about the 3080TI unless 3080 and 3090 have the same thermal pad placement and sizes ?
CPU: 10900K cooled with NZXT Z73 MOBO: Z490 Aorus Xtreme GPU: EVGA 3080TI FTW3 ULTRA PSU: Seasonic Prime Gold 1300W RAM: Corsair vengeance RGB PRO 16gb x 2 Storage: Samsung 980 Pro x 2, Samsung 960 Evo Case: O11D Lianli Case fans: Lian Li AL120 Unifans x 9, Arctic F8 PWM x 2
|
talon951
FTW Member
- Total Posts : 1026
- Reward points : 0
- Joined: 2020/10/06 02:41:19
- Status: offline
- Ribbons : 3
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/07 11:17:29
(permalink)
https://forums.evga.com/m/tm.aspx?m=3406588
|
dryja123
New Member
- Total Posts : 46
- Reward points : 0
- Joined: 2016/02/13 19:29:23
- Status: offline
- Ribbons : 1
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/07 19:05:47
(permalink)
|
Jyoussi
New Member
- Total Posts : 44
- Reward points : 0
- Joined: 2021/06/13 22:48:47
- Status: offline
- Ribbons : 0
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/07 20:04:23
(permalink)
I got home and first thing i did was opened up the whole GPU, itsnot big its mostly an exhaust pipe :X.. Then i put theral paste over everything that touches the frame. These spots have little thermal pads i guess u could call them, theyr just pads reallyt.. I goooooed up the pads and the exhaust pipe too. used a whole tube on it. It doesnt even get to 70 cellsius in socal summer...when installed i have 2 fans blowing out of the doorless case.
|
Jobotoo
Superclocked Member
- Total Posts : 188
- Reward points : 0
- Joined: 2011/02/08 14:53:32
- Status: offline
- Ribbons : 0
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/08 13:57:29
(permalink)
|
Pro4tlzz
New Member
- Total Posts : 34
- Reward points : 0
- Joined: 2018/02/03 05:01:45
- Status: offline
- Ribbons : 0
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/19 09:06:06
(permalink)
dryja123
You can buy the thermal putty here:
argh unfortunately not in europe
|
Intoxicus
iCX Member
- Total Posts : 406
- Reward points : 0
- Joined: 2009/10/23 19:03:35
- Status: offline
- Ribbons : 0
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/23 09:41:39
(permalink)
EVGATech_DanielM
Please note that if you ever need to RMA the card - we will need the factory thermal pads installed. We can assist in the stock pads prior to RMA.
If this is true then EVGA should be making it very easy for us to buy/obtain a full and complete set of replacement pads and putty.
"Humans are not rational animals, humans are rationalizing animals." -Robert A Heinlein
|
ObscureEmpyre
SSC Member
- Total Posts : 972
- Reward points : 0
- Joined: 2012/01/15 14:40:05
- Status: offline
- Ribbons : 7
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/08/23 10:24:15
(permalink)
Intoxicus
EVGATech_DanielM
Please note that if you ever need to RMA the card - we will need the factory thermal pads installed. We can assist in the stock pads prior to RMA.
If this is true then EVGA should be making it very easy for us to buy/obtain a full and complete set of replacement pads and putty.
The putty is available to purchase directly from the website. That pads, however, are not. Hopefully this changes down the road… or immediately since they seem to be a common need.
|
augiem
Superclocked Member
- Total Posts : 133
- Reward points : 0
- Joined: 2015/11/25 15:48:58
- Status: offline
- Ribbons : 0
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/09/03 14:18:24
(permalink)
Anyone know the thermal specs on the putty and pads on 3080 TI FTW3 Ultra? I see their Kingpin waterblock comes with this brand: https://www.thermazig.com/But I can't find any info on the thermal characteristics. Their site shows pads from 3.2 W/mK to 13 W/mK. And I can't find anything on the putty. I would like to replace all the pads and putty with the most thermally conductive I can find but there's no point in replacing them if they're already using 13 W/mK. I'm currently getting rather terrible temps of 87C on the GPU and 94C on the memory in a room that's probably around 75 f after only about 5 minutes running Ark Survival. Idles at 60 GPU, 70 Mem.
post edited by augiem - 2021/09/03 14:23:27
|
KingEngineRevUp
FTW Member
- Total Posts : 1030
- Reward points : 0
- Joined: 2019/03/28 16:38:54
- Status: offline
- Ribbons : 9
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/09/03 14:27:23
(permalink)
augiem
Anyone know the thermal specs on the putty and pads on 3080 TI FTW3 Ultra? I see their Kingpin waterblock comes with this brand: https://www.thermazig.com/
But I can't find any info on the thermal characteristics. Their site shows pads from 3.2 W/mK to 13 W/mK. And I can't find anything on the putty. I would like to replace all the pads and putty with the most thermally conductive I can find but there's no point in replacing them if they're already using 13 W/mK.
I'm currently getting rather terrible temps of 87C on the GPU and 94C on the memory in a room that's probably around 75 f after only about 5 minutes running Ark Survival. Idles at 60 GPU, 70 Mem.
What fan profile are you using? What happens if you put the fans at 100% or the case open? What card were you using before? Remember, this is a 400-450W card. Previous 2080 Tis were 300Wish. If you open your case and temperatures drop a lot, more than likely it is a case flow issue.
|
rjbarker
CLASSIFIED Member
- Total Posts : 3214
- Reward points : 0
- Joined: 2008/03/20 10:07:05
- Location: Vancouver Isle - Westcoast Canada
- Status: offline
- Ribbons : 21
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2021/09/03 19:36:52
(permalink)
Jobotoo
dryja123
You can buy the thermal putty here: https://www.evga.com/prod...aspx?pn=M047-10-000003
This^^ plus you can get thermal pad replacements from EVGA support.
+1 ...I purchased the thermal Putty from Evga and there also sending me a set of replacement pads for my 3080 FTW3....
I9 12900K EK Velocity2 / ROG Z690 Apex/ 32G Dominator DDR5 6000/ Evga RTX 3080Ti FTW3 EK Vector / 980 Pro 512G / 980 Pro 1TB/ Samsung 860 Pro 500G/ WD 4TB Red / AX 1600i / Corsair 900D & XSPC 480 * 360 * 240 Rads XSPC Photon 170 Rez-Vario Pump Combo - Alienware 3440*1440p 120Hz/ W11
|
keshy19
New Member
- Total Posts : 10
- Reward points : 0
- Joined: 2021/05/04 19:38:43
- Status: offline
- Ribbons : 0
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2022/01/06 03:58:15
(permalink)
I'm curious about doing this myself. I called EVGA and asked if they would replace the thermal paste and thermal pads with my own, I have some of the Kryonaut extreme and i wanted to get some of their pads as well. Interestingly enough, they said they would be willing to replace the pads and paste for me. But it would only be with their factory standard paste and pads, they wont use mine and the rep I spoke to tried to ask for me. I was somewhat impressed they were willing to do it at all but its too bad they wouldnt be willing to use my cooling compounds. Probably better than what most companies would ever offer. The only challenge is finding a place to perform this service, Microcenter wont. I'd really rather not do it myself
|
KingEngineRevUp
FTW Member
- Total Posts : 1030
- Reward points : 0
- Joined: 2019/03/28 16:38:54
- Status: offline
- Ribbons : 9
Re: 3080TI FTW3 Ultra - thermal pads and thermal putty
2022/01/07 08:02:27
(permalink)
keshy19
I'm curious about doing this myself. I called EVGA and asked if they would replace the thermal paste and thermal pads with my own, I have some of the Kryonaut extreme and i wanted to get some of their pads as well. Interestingly enough, they said they would be willing to replace the pads and paste for me. But it would only be with their factory standard paste and pads, they wont use mine and the rep I spoke to tried to ask for me. I was somewhat impressed they were willing to do it at all but its too bad they wouldnt be willing to use my cooling compounds. Probably better than what most companies would ever offer. The only challenge is finding a place to perform this service, Microcenter wont. I'd really rather not do it myself
They're not going to use your cooling compound because they don't want to be liable for something they didn't intentionally design too be used on their cards.
|