norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
I have a issue after I try reinstall my thermaltake frio. The system stay unstable but I think it's for bad installation. I try many things and system beep, make the ff codes one time and try loading windows and shutdown and don't start anymore. I enter in bios, but not have much time after system goes down. The BIOS is default values. I can't access this. I Think my cpu is don't seated correct, i'll try with stock cooler. PS: I clear cmos, remove cmos battery, verify psu connections. My system: bios profile : BIOS Version: P08
**System ** CPU Freq, MHz: 3000 GHZ FSB Reference Clock, MHz: 1333 CPU Multiplier: [9X] PCle x16-1 & 16-2, MHz: [AUTO] PCle x16-3, MHz: [AUTO] SPPc->MCP Ref Clock, MHz: [AUTO] nForce SPP --> nForce MCP: [5X] nForce SPP c-- nForce MCP: [5X] **Spread Spectrum** CPU Spread Spectrum: [Disabled] HT Spread Spectrum: [Disabled] PCle Spread Spectrurn(SPP): [Disabled] PCle Spread Spectrurn(MCP): [Disabled] SATA Spread Spectrum: [Disabled] **FSB & Memorv Config** FSB - Memory Clock Mode: [unlinked] FSB - Memory Ratio: FSB (QDR), MHz: [AUTO] Actual FSB (QDR), MHz: 1333 x MEM (DDR), MHz: 1333 [STOCK] My memories are DDR3 1333 fabric. Actual MEM (DDR), MHz: 1333
P1: auto P2: auto **Memory Timing Setting** Memory Timing Setting: [expert] tCL (CAS Latency): 9
tRCD: 9
tRP: 9
tRAS: 24
Command Per Clock: [2T]
** Advanced Memory Settings **
tRRD: [Auto] (5)
tRC: [Auto] (45)
tWR: [Auto] (12)
tWTR: [Auto] (18)
tFAW: [Auto] (39)
tREF: [Auto] 7.7uS
tRFC: [Auto] (88)
**System Voltages**
CPU Core: AUTO [1.18]
CPU FSB: AUTO [1.1]
Memory: AUTO[1.50v]
nForce SPP: AUTO[1.30]
nForce MCP: AUTO[1.500]
GTLVREF Lane 0: [Auto] +00mv
GTLVREF Lane 1: [Auto] +00mv GTLVREF Lane 2: [Auto] +00mv GTLVREF Lane 3: [Auto] +00mv **CPU Configuration**
Limit CPUlD Maxval: Disabled
Intel Speedstep: Disabled
xPPM Mode: [Native]
CPU Thermal Control: [Disabled]
C1E Enhanced Halt State: [Disabled]
Execute Disable Bit: [disabled]
Virtualization Technology: [Disabled]
CPU Core 0: [Enabled]
CPU Core 1: [Enabled] Thanks in advance.
post edited by norum - 2011/03/24 11:16:59
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 06:42:07
(permalink)
Did you try reseating your CPU as you state in your above post? Does the board cycle quickly through the LED codes and end on "FF", or does it go directly to "FF" as soon as you power it on? Gently, yet firmly press down on your BIOS chip to ensure it is properly seated. You state in your above post that you cannot access your BIOS...if that is so, then where did you obtain the settings that you entered on the BIOS template. Additionally, please edit your first post and add the RAM part number.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 07:40:23
(permalink)
Did you try reseating your CPU as you state in your above post? Yes! Does the board cycle quickly through the LED codes and end on "FF", or does it go directly to "FF" as soon as you power it on? When I First Power it ON, yes it ends on ff, good!. they go of all the cycles and try load Windows, before the finish of the load screen, they shutdown. And I try soon turn it on. It's GO FF straight and all lights oN or SHutdown =/ Gently, yet firmly press down on your BIOS chip to ensure it is properly seated? YES! You state in your above post that you cannot access your BIOS...? Well I Can Access less then a minute my bios. I Inform my previously bios and what I can make with a minute. if that is so, then where did you obtain the settings that you entered on the BIOS template. Additionally, please edit your first post and add the RAM part number. In my signature is my Config.
post edited by norum - 2011/03/24 07:44:50
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 07:50:17
(permalink)
I don't see the RAM part number. The following is not the part number: 4GB DDR3 Corsair XMS3
We need the part number as written on the actual sticks or the packaging.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 10:31:26
(permalink)
Well Done . 9 9 9 24 1.5v XMS3DHX CAS 9 (I'm not in home, Well the memories in the PC).
I need answers!!!
And a good Signal or no?
I turned on the pc, enter the bios, disabled the 1.44floppy and disabled the functions in cpu configuration intel speedstep, halt state, cpu thermal control, virtualization tecnology, save with f10 and it's loading windows, I'm in desktop. Change data and hour and access the forum, but when I see my post the pc shutdown again. I'll try with a stock cpu cooler with all fine and see if it's the thing.
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 10:52:41
(permalink)
If the following link is to your RAM, the voltage should be 1.80v, not 1.50v. http://www.newegg.com/Pro...x?Item=N82E16820145200 Please try the following settings: BIOS Version: P 08
**System ** CPU Freq, MHz: 3000 GHZ FSB Reference Clock, MHz: 333 (1333) CPU Multiplier: [9X] PCle x16-1 & 16-2, MHz: [AUTO] PCle x16-3, MHz: [AUTO] SPPc->MCP Ref Clock, MHz: [AUTO] nForce SPP --> nForce MCP: [5X] nForce SPP c-- nForce MCP: [5X] **Spread Spectrum** CPU Spread Spectrum: [ Disabled] HT Spread Spectrum: [ Disabled] PCle Spread Spectrurn(SPP): [ Disabled] PCle Spread Spectrurn(MCP): [ Disabled] SATA Spread Spectrum: [ Disabled] **FSB & Memorv Config** FSB - Memory Clock Mode: [ unlinked] (link) FSB - Memory Ratio: (sync) FSB (QDR), MHz: [ AUTO] (1333) Actual FSB (QDR), MHz: 1333 x MEM (DDR), MHz: 1333 Actual MEM (DDR), MHz: 1333
P1: auto P2: auto **Memory Timing Setting** Memory Timing Setting: [ expert] (manual) tCL (CAS Latency): 9
tRCD: 9
tRP: 9
tRAS: 24
Command Per Clock: [2T]
** Advanced Memory Settings **
tRRD: [Auto] (5)
tRC: [Auto] (45)
tWR: [Auto] (12)
tWTR: [Auto] (18)
tFAW: [Auto] (39)
tREF: [Auto] 7.7uS (7.8uS)
tRFC: [Auto] (88)
**System Voltages** (manually set the System Voltages)
CPU Core: AUTO [1.18] (1.25v)
CPU FSB: AUTO [1.1] (1.20v)
Memory: AUTO[1.50v] (1.65v)
nForce SPP: AUTO[1.30] (1.40v)
nForce MCP: AUTO[1.500] (1.50v)
GTLVREF Lane 0: [Auto] +00mv
GTLVREF Lane 1: [Auto] +00mv GTLVREF Lane 2: [Auto] +00mv GTLVREF Lane 3: [Auto] +00mv **CPU Configuration**
Limit CPUlD Maxval: Disabled
Intel Speedstep: Disabled
xPPM Mode: [Native]
CPU Thermal Control: [Disabled]
C1E Enhanced Halt State: [Disabled]
Execute Disable Bit: [disabled]
Virtualization Technology: [Disabled]
CPU Core 0: [Enabled]
CPU Core 1: [Enabled]
post edited by VistaHead - 2011/03/24 11:24:01
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:12:47
(permalink)
no man sorry they are 1333. 1.5v and it's four 4x 1gb, I have this build past 3 years.
post edited by norum - 2011/03/24 11:16:14
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:16:23
(permalink)
norum
no man sorry they are 1333. 1.5v and it's four 4x 1gb
Please post a link to the RAM. Part of the problem is that it is low voltage RAM...some 790i boards play well with it....some don't. Please see the changes to the template in post # 6 for the RAM.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:19:36
(permalink)
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:23:37
(permalink)
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:27:08
(permalink)
My pc is not running fine, sometime I can enter the bios and pc is go down.
I want Explain to you. I have 2 corsair Platinum XMS 3 voltage are 1.6V and the mobo put them in 1.5V.
I have other 2 Corsair DHX XMS3 voltagem are 1.5V and the mobo put them 1.5V.
You think is my memory is the problem ?
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:29:12
(permalink)
norum
My pc is not running fine, sometime I can enter the bios and pc is go down.
I repeat....try all of the settings in post #6.
|
JeffreyHam
R.I.P. Friend
- Total Posts : 7830
- Reward points : 0
- Joined: 2006/08/08 10:31:07
- Location: Missouri Ozarks, U.S.A.
- Status: offline
- Ribbons : 126
Re:790i PROBLEMS
2011/03/24 11:29:51
(permalink)
Op: even though both sets of RAM are rated to run at 9-9-9-24 1.6v.....part of you problems may be due to putting two different models together. You should be using 4 identical stix.
 PLEASE REMEMBER TO UPLOAD A COPY OF YOUR INVOICE  = My Current Linked and Synced Settings All detailed system components are listed on my Mods Rigs page.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:30:35
(permalink)
You Use this voltages in your system? I'm using this ram normally a long time! But I want a advice if my mobo doesn't show video. What Should I do ?
post edited by norum - 2011/03/24 11:33:05
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:31:57
(permalink)
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:33:17
(permalink)
norum
You Use this voltages in your system?
Each PC is different. We have different components. Please try the settings I am suggesting in post #6.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:35:57
(permalink)
JeffreyHam
Op: even though both sets of RAM are rated to run at 9-9-9-24 1.6v.....part of you problems may be due to putting two different models together. You should be using 4 identical stix.
Yep. Well I run two ran identical if it's the problem.
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:38:28
(permalink)
VistaHead
norum
My pc is not running fine, sometime I can enter the bios and pc is go down.
I repeat....try all of the settings in post #6.
Ok. To run this ram together I need 1.6V?
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
JeffreyHam
R.I.P. Friend
- Total Posts : 7830
- Reward points : 0
- Joined: 2006/08/08 10:31:07
- Location: Missouri Ozarks, U.S.A.
- Status: offline
- Ribbons : 126
Re:790i PROBLEMS
2011/03/24 11:40:20
(permalink)
PLEASE REMEMBER TO UPLOAD A COPY OF YOUR INVOICE = My Current Linked and Synced Settings All detailed system components are listed on my Mods Rigs page.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:40:21
(permalink)
CPU Core: AUTO [1.18] (1.25v) - You wanna Say 1.25V in Windows? Because 1.25v in my bios is 1.3V.
CPU FSB: AUTO [1.1] (1.20v) - OK
Memory: AUTO[1.50v] (1.65v) - ok
nForce SPP: AUTO[1.30] (1.40v) - ok
nForce MCP: AUTO[1.500] (1.50v)- ok
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
JeffreyHam
R.I.P. Friend
- Total Posts : 7830
- Reward points : 0
- Joined: 2006/08/08 10:31:07
- Location: Missouri Ozarks, U.S.A.
- Status: offline
- Ribbons : 126
Re:790i PROBLEMS
2011/03/24 11:43:31
(permalink)
norum
VistaHead
norum
My pc is not running fine, sometime I can enter the bios and pc is go down.
I repeat....try all of the settings in post #6.
Ok. To run this ram together I need 1.6V?
I MUST repeat what I said in post #13: " Op: even though both sets of RAM are rated to run at 9-9-9-24 1.6v.....part of you problems may be due to putting two different models together. You should be using 4 identical stix. "
PLEASE REMEMBER TO UPLOAD A COPY OF YOUR INVOICE = My Current Linked and Synced Settings All detailed system components are listed on my Mods Rigs page.
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:44:10
(permalink)
norum
VistaHead
norum
My pc is not running fine, sometime I can enter the bios and pc is go down.
I repeat....try all of the settings in post #6.
Ok. To run this ram together I need 1.6V?
You came here looking for assistance, am I am attempting to assist you. I know what I am doing, so please try all of the settings that I provided in post #6. The changes that I made are in parenthesis. If there is no parenthesis, then make sure that the setting that is listed is entered in your BIOS. I want you to set the RAM voltage to 1.65v because you are using 4 modules so you may need a slight increase in voltage past the manufacturer's recommended voltage of 1.60v. Try the settings, and if they do not work for you, then post what happened in this thread, and either I, or someone else will assist you further.
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:45:58
(permalink)
norum
CPU Core: AUTO [1.18] (1.25v) - You wanna Say 1.25V in Windows? Because 1.25v in my bios is 1.3V.
CPU FSB: AUTO [1.1] (1.20v) - OK
Memory: AUTO[1.50v] (1.65v) - ok
nForce SPP: AUTO[1.30] (1.40v) - ok
nForce MCP: AUTO[1.500] (1.50v)- ok
I want you to set the settings in post #6 in your BIOS. The board has VDroop, so the actual applied voltage in Windows may be less than what you set in the BIOS.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 11:49:45
(permalink)
Fine! Thanks, i Will try tonight with new cooler and see what's happening if the problem persists I don't post nothing. I will POST tomorrow in work so. I know that you are experienced users, but I'm said I have problems, my pc is shutdown or presents the FF and Red Light Problem because the FF or no present the redlight, but shows only FF and do nothing. So I hope that I can test your settings in post#6
post edited by norum - 2011/03/24 11:55:37
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 11:53:46
(permalink)
I see that you edited post #9 and added an additional second set of RAM. Jeffreyham is correct....mixing and matching RAM can cause issues. Try the settings in post #6 with all four sticks, but you may end up having to remove two of them.
post edited by VistaHead - 2011/03/24 11:57:50
|
JeffreyHam
R.I.P. Friend
- Total Posts : 7830
- Reward points : 0
- Joined: 2006/08/08 10:31:07
- Location: Missouri Ozarks, U.S.A.
- Status: offline
- Ribbons : 126
Re:790i PROBLEMS
2011/03/24 11:54:24
(permalink)
norum
Fine! Thanks, i Will try tonight with new cooler and see what's happening if the problem persists I don't post nothing. I will POST tomorrow in work so.
A new cooler isn't going to make a difference if, you need to reseat the chip itself. While you have the cooler off.....remove the chip too. Clean it up real good and make sure that you carefully and properly reinstall it.
PLEASE REMEMBER TO UPLOAD A COPY OF YOUR INVOICE = My Current Linked and Synced Settings All detailed system components are listed on my Mods Rigs page.
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 12:01:12
(permalink)
norum
Fine! Thanks, i Will try tonight with new cooler and see what's happening if the problem persists I don't post nothing. I will POST tomorrow in work so. I know that you are experienced users, but I'm said I have problems, my pc is shutdown or presents the FF and Red Light Problem because the FF or no present the redlight, but shows only FF and do nothing.
So I hope that I can test your settings in post#6
But you also mention in one of your posts that you were at your desktop, so it may be a BIOS setting issue. Like Jeffreyham suggested, take a good look at your CPU and the CPU socket. Make sure that the socket has no bent pins, discoloration, etc. Correctly apply some good TIM, and make sure that your CPU cooler is properly mounted.
|
norum
New Member
- Total Posts : 54
- Reward points : 0
- Joined: 2008/09/15 17:53:30
- Status: offline
- Ribbons : 0
Re:790i PROBLEMS
2011/03/24 12:04:23
(permalink)
Oh yes It is. Because my cooler don't fix firmly, so I have care with mount and unmount CPU.
I make a clear in the socket specially.
CM 690 / AsRock P67 Extreme 4 Rev 3.0/ Loading GTX 560 Ti | EVGA 9800GTX+/ Core I5 2500K @ 4.5 Ghz/ Thermaltake Frío/4GB DDR3 Corsair XMS3/ LG 23º Black Piano/Corsair - 950TX /Seagate 1TB + 250GB/Logitech MX-518/Plantronics Gamecom Pro 1/Windows 7 ULTIMATE 64 Bits
|
D.M.W.T
FTW Member
- Total Posts : 1731
- Reward points : 0
- Joined: 2007/11/24 18:04:33
- Location: I am not sure
- Status: offline
- Ribbons : 4
Re:790i PROBLEMS
2011/03/24 12:05:52
(permalink)
norum
Fine! Thanks, i Will try tonight with new cooler and see what's happening if the problem persists I don't post nothing. I will POST tomorrow in work so. I know that you are experienced users, but I'm said I have problems, my pc is shutdown or presents the FF and Red Light Problem because the FF or no present the redlight, but shows only FF and do nothing.
So I hope that I can test your settings in post#6
Not to jump in and misdirect anyone, but if I am reading correctly the red light at the top of the board is on or coming on? beofre or while its shutting itself off? This problem right after a new cooler was installed? I gotta say unless I a missing something I really think you need to follow the above step in post # 2 again with the stock cooler jsut to see what happens. I think your messing something up (not on purpose of course), but it seems too coincidental that it was stable for 3 years then right after a cooler install it shuts down immediately and wont post.
|
VistaHead
Omnipotent Enthusiast
- Total Posts : 9368
- Reward points : 0
- Joined: 2009/02/17 18:42:22
- Status: offline
- Ribbons : 131
Re:790i PROBLEMS
2011/03/24 12:08:55
(permalink)
norum
Oh yes It is. Because my cooler don't fix firmly, so I have care with mount and unmount CPU.
I make a clear in the socket specially.
If your cooler will not properly mount, then you need to use a different aftermarket cooler, or the stock cooler. If you use the stock cooler, make sure that all four push-pins are properly seated.
|
