I am having a problem getting past the 4.2 GHz mark on the CPU, when it blue screens, it mangles the video in the process and I have to reload those. Here is the template

Mother Board ( EVGA X58 Classified E-760-A1 )                                                      
Drivers ( 6.1.7600.16385 )
Bios ( Award v6.00PG )                                                                                                    
 CPU ( 975EE ) D0 (000106A5H) 
CPU Cooler ( Heat Killer 3.0 )( 655 pump and a Thermochill PA120.3 radiator with 100 CFM Fans)
Memory (G Skill F3-12800CL7-2GPI x3 )
PSU ( Corsair HX1000W + Corsair HX850W )
GPU ( GTX 480 with DD all Copper blocks and 3 Koolance Radiators and a 355 pump and 100 CFM Fans )
Drivers ( 197.75 )                                                                                                 
Operating System ( Windows 7 64 Ultimate )


Frequency Control
CPU Clock Ratio ( 31X )                                                                                        
CPU Host Frequency (Mhz) ( 136 )                                                                     
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) (AUTO )                                               
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )  


Memory Feature       
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 1600Mhz / 2:12 )                                                               
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( AUTO )
tCL Setting ( 7 )
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 24 )
tRFC Setting ( 88 )
Command Rate ( 1t )


Voltage Control
EVGA VDroop Control ( With VDroop )
CPU VCore ( 1.3625 )                                                                                               
CPU VTT Voltage ( +400 )
CPU PLL VCore ( 1.905 )
IOH PLL VCore ( 1.815)
DIMM Voltage ( 1.7 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( 1.275 )
IOH VCore ( Auto )
IOH/ICH I/O Voltage ( Auto )
VTT PWM Frequency ( 610 KHZ )
CPU PWM Frequency ( 1210 KHZ )
CPU Impedance ( AUTO )
QPI Signal Compensation ( AUTO )
ICH VCore ( Auto )



CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Enabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 6.400 GT/s )
OC Recovery ( Disabled )


PnP/PCI     PCI Express
Maximum Payload Size ( 4096 )
 
Power Management Setup
ACPI Suspend Type ( S3 )  
HPET Support ( Enabled )    
HPET Mode ( 64-bit )

My temps when running at 100% like this are as follows:
Core 1: 65 c
Core 2 : 54 c
Core 3 : 62 c
Core 4 : 52 c

running the fans between 1500 and 2000 rpm and water temp on the CPU loop is reaching about 29.2 C
Air cooling on the memory.
Crashes happen when running Prime 95 with the last blue screen with a 000000000a error code. I have been getting 00000101a and a few 000000055a errors as well. Have not seen the 125 error yet. I have manually pushed a few of the clocks and that is how I got to 4.2 but if I load it down for any length of time I will crash or freeze up.

I don't know why really but I think you'll get more help in the EVGA X58 SLI Forum instead. This thread  under normal circumstances would be the right place for normal logically thinking adults but they are a bunch of cranky geekinoids up there on there shiny hill. Tread lightly and head up there if you want some help with this. They might slap you around and laugh at you a bit  in the end I think it will be worth your effort and you can always come back here with us low life if you don't fit in. LOL
Good Luck

edit:removed the unnecessary sarcasm so as to get to the point