EVGA_JacobF
EVGA Alumni
- Total Posts : 11559
- Reward points : 0
- Joined: 1/17/2006
- Location: Brea, CA
- Status: offline
- Ribbons : 26
Monday, November 09, 2009 8:37 PM
(permalink)
This BIOS is ONLY for the EVGA X58 SLI Motherboard (part number 132-BL-E758-) SZ2X Updates: - Adds support for 2TB Partitions (DATA)
BIOS updating can be accomplished VIA the below methods:
CD/DVD Installation - Recommended installation method- Download the following .iso file: E758_SZ2X.iso
- Use a CD Burning software to burn the .iso image onto a blank CD (Nero, Alochol 120%, MagicISO etc.)
- After it has burned, insert CD and restart the machine, go into the BIOS and load defaults, save and exit
- Now set the CD Drive as the primary boot device, or press escape while the system is booting to select CD as the bootable device.
- After flash remove the CD, and power off PC Completely.
- Turn on the PC and load defaults in BIOS
USB FLOPPY Installation - Recommended installation method- Download the following executable: E758_SZ2X.exe
- Insert blank floppy disk into drive and run executable
- After the floppy has written fully, restart the machine, go into the BIOS and load defaults, save and exit
- Now set the USB Floppy as the primary boot device, or press escape while the system is booting to select USB Floppy as the bootable device
- After flash remove the floppy, power off PC Completely
- Turn on the PC and load defaults in BIOS
USB Flash Drive Installation - Alternate installation method- Download: E758SZ2X.bin
- Visit this thread and follow the installation instructions. (thanks 30h6).
Warning:
**Do not restart or interrupt your PC while the flash is ongoing
**Do not Flash BIOS on overclocked settings
**It is always recommended to power-down after flash and Clear CMOS
post edited by EVGATech_MattM - Thursday, August 07, 2014 3:23 PM
|
Afterburner
EVGA Forum Moderator
- Total Posts : 17389
- Reward points : 0
- Joined: 9/21/2007
- Location: It's... Classified Yeeeeeeeeeeaaaaaaah........
- Status: offline
- Ribbons : 110
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 8:37 PM
(permalink)
|
NameBrandHuman
Superclocked Member
- Total Posts : 185
- Reward points : 0
- Joined: 6/30/2007
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 9:10 PM
(permalink)
Wow i just went to update my bios and this was just release shweet!!! Thanks...
Case: Antec 902 Cpu: Core i7 920 @ 3.8ghz (Vcore 1.21875 w/vdroop 19 multi x 201BClk) Cpu Cooler: Vigor Monsoon III LT Hard Drive: 2 x 500gb Western Digital Blacks Mobo: EVGA X58 3xsli Ram: 3x2gb OCZ platinum ddr3 @ 1600mhz 7-7-7-24 Vid Card: XFX 5870 Optical Drive:1 x LG 22x DVD-RW , 1 x Liteon BR Reader PSU: Corsair 850w Heatware
|
i_cruz
iCX Member
- Total Posts : 491
- Reward points : 0
- Joined: 12/27/2008
- Location: Central Ohio
- Status: offline
- Ribbons : 1
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 9:42 PM
(permalink)
> PSU: OCZ Fatal1ty 1000W> Mainboard: EVGA Z690 CLASSIFIED (BIOS 2.08)> AIO: EVGA CLC 280mm AIO> CPU: Intel i7-13700k 3.4GHz> Physical Memory: G.SKILL Trident Z5 64GB (4 x 16GB) DDR5 > Physical Memory Model#: F5-6400J3239G16GA2-TZ5RK> Monitor: Samsung G9> Video Card: EVGA RTX 3090 Ti FTW3[URL=https://www.evga.com/associates/default.aspx?associatecode=HV4ZYIDMNODLH84]  [
|
NameBrandHuman
Superclocked Member
- Total Posts : 185
- Reward points : 0
- Joined: 6/30/2007
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 9:46 PM
(permalink)
Ok I can't get bios to post if i load my profile ****? Defaults posts fine. I think i had sz2e on it before i updated it.
post edited by NameBrandHuman - Monday, November 09, 2009 9:51 PM
Case: Antec 902 Cpu: Core i7 920 @ 3.8ghz (Vcore 1.21875 w/vdroop 19 multi x 201BClk) Cpu Cooler: Vigor Monsoon III LT Hard Drive: 2 x 500gb Western Digital Blacks Mobo: EVGA X58 3xsli Ram: 3x2gb OCZ platinum ddr3 @ 1600mhz 7-7-7-24 Vid Card: XFX 5870 Optical Drive:1 x LG 22x DVD-RW , 1 x Liteon BR Reader PSU: Corsair 850w Heatware
|
Zaskar
Superclocked Member
- Total Posts : 126
- Reward points : 0
- Joined: 10/14/2007
- Status: offline
- Ribbons : 2
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 10:05 PM
(permalink)
Should never load a profile from a previous bios, even if it works it may be unstable. Just note the settings and recreate them. It kind of stinks as it limits the usefulness of saving a profile, but unfortunately it what we have to do.
post edited by Zaskar - Tuesday, November 10, 2009 0:44 PM
EVGA X58 Classified Intel i7 975 Corsair Dominator 1600mhz 3x2gb Nvidia GTX 295 Auzentech X-Fi Forte
|
NameBrandHuman
Superclocked Member
- Total Posts : 185
- Reward points : 0
- Joined: 6/30/2007
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 10:18 PM
(permalink)
Thanks for the reply. I never had an issue using the profile before this time. But it's all good i just put settings in manually and all is well again.
Case: Antec 902 Cpu: Core i7 920 @ 3.8ghz (Vcore 1.21875 w/vdroop 19 multi x 201BClk) Cpu Cooler: Vigor Monsoon III LT Hard Drive: 2 x 500gb Western Digital Blacks Mobo: EVGA X58 3xsli Ram: 3x2gb OCZ platinum ddr3 @ 1600mhz 7-7-7-24 Vid Card: XFX 5870 Optical Drive:1 x LG 22x DVD-RW , 1 x Liteon BR Reader PSU: Corsair 850w Heatware
|
8800gts320
Superclocked Member
- Total Posts : 154
- Reward points : 0
- Joined: 5/25/2007
- Status: offline
- Ribbons : 1
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 10:20 PM
(permalink)
Just Flashed,all is good..Running Rev 1.0 X58
2 Poster above,of course you cant load your old profiles,just make new one's..
  EVGA X58 SLI (E758)
Intel i7 920 C0 @ 3.8
Evga GTX 295 Dual PCB
OZC DD3 15000
Corsair 750 W
Seagate 250 in raid 0
W7 64
|
grd003
Superclocked Member
- Total Posts : 186
- Reward points : 0
- Joined: 10/3/2009
- Location: SW Florida USA
- Status: offline
- Ribbons : 1
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 11:35 PM
(permalink)
Loaded via CD; reloaded old BIOS profile; booted; things work the same so far @4.3573GHz
Intel i7 920 4378.2MHz -- EVGA E758 -- 12GB: 6GB Mushkin Redlines & 6GB Geil Ultra Thermalright IFX-14, Inferno Fire eXtinguisher -- ATI 5750 @ 850/1400 -- OCZ Fatal1ty 550W COOLER MASTER Nvidia 690 Green/Black case -- OCZ Agility 120GB SSD -- 5x1.5TB Raid-0 Adaptec 1430SA Raid Controller -- LSI SAS2 2008 Falcon -StorPort Raid Controller -- 4x2x500GB External Raid-0 LG Blu-ray Burner -- LG M237WD 23" HDMI 1080P LCD w/tv tuner -- Windows 7 x64 Ultimate  
|
lam_das
iCX Member
- Total Posts : 266
- Reward points : 0
- Joined: 6/8/2009
- Status: offline
- Ribbons : 1
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 11:40 PM
(permalink)
When are we going to be delighted with a Changelog saying "S3 issues finally fixed...:)"...  EVGA, please delight us! We paid you $300 for this board! Gave you a good name for good customer service all over the net! Let me know if you have forgotten what S3 issues we are facing. They are documented in the archive, under every BIOS released since the beginning of time. But lastly, they were all documented in SZ2P thread.
EVGA X58 SLI Rev 1.1 i7 920 D0 LinX/Prime Stable 4.4(21x210) HT ON 1.3125vcore, +100mV, vDIMM 1.625v, Rest Auto OCZ Gold 6GB 1680 (2:8) 9 9 9 24 1T Prolimatech Megahalems (Push/Pull) Because of S3 issues: 21x196, Auto vcore, 2:8, 8-8-8-24-1T 12GB.
|
EVGA_JacobF
EVGA Alumni
- Total Posts : 11559
- Reward points : 0
- Joined: 1/17/2006
- Location: Brea, CA
- Status: offline
- Ribbons : 26
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Monday, November 09, 2009 11:51 PM
(permalink)
lam_das
When are we going to be delighted with a Changelog saying "S3 issues finally fixed...:)"... EVGA, please delight us! We paid you $300 for this board! Gave you a good name for good customer service all over the net!
Let me know if you have forgotten what S3 issues we are facing. They are documented in the archive, under every BIOS released since the beginning of time. But lastly, they were all documented in SZ2P thread.
Does it say 1.0 or 1.1 on your board?
|
iai290
New Member
- Total Posts : 69
- Reward points : 0
- Joined: 12/13/2008
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 1:38 AM
(permalink)
How about, when are we going to get a changelog that says "Hauppauge tv tuners finally work with this motherboard"
|
hnic4life
New Member
- Total Posts : 3
- Reward points : 0
- Joined: 9/2/2009
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 2:01 AM
(permalink)
why is it when I go to click those links to start my download... I get a error page everytime
|
rottenmutt
Superclocked Member
- Total Posts : 246
- Reward points : 0
- Joined: 10/30/2005
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 2:02 AM
(permalink)
rev 1.0
any new info on the dreaded S3 support?
EVGA X58 Classified|i7-920 @ 4.2GHz on H20|Tri SLI GTX 680|CORSAIR 6GB DDR3 CM3X2G1600C8D|SB Xfi|ThoughPower 1200W EVGA X58 Classified|i7-975 @ 4.2GHz on H20|2x GTX 275|CORSAIR 6GB DDR3 CM3X2G1600C8D EVGA X58 Rev 1.0|i7-930 @ 4.00GHz|GTX 580, GTX 470|6GB Kingston PC3-10600 Skulltrail|2x E5450 @ 3.6GHz on H2O|2X GTX 480|SB Xfi|ThoughPower 1200W Skulltrail|2x E5430 @ 3.2GHz on H2O|GTX 580 3GB|SB Xfi|ThoughPower 1200W H8DCE|2x Opteron 270|4GB|2X GTX 565ti KFN32D-SAS|2x Opteron 2354|GTX 480, GTX 470
|
markgrant
New Member
- Total Posts : 35
- Reward points : 0
- Joined: 3/17/2003
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 4:01 AM
(permalink)
EVGATech_JacobF
Does it say 1.0 or 1.1 on your board?
where is this located?
Intel i7 920 D0 (not overclocked) Corsair Hydro H50 eVGA X58 SLI e758 v1.1 6x2GB Corsair Dominator 1600MHz 8-8-8-24 2x BFG GTX285 OC Silverstone ST-1000NV Intel X25-M 160gb SSD 2x Seagate Baracuda LP 1.5TB Raid 1 Seagate 750GB 7200.10 Silverstone FT-01B-W
|
Bobmitch
CLASSIFIED ULTRA Member
- Total Posts : 7822
- Reward points : 0
- Joined: 5/7/2007
- Status: offline
- Ribbons : 49
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 5:08 AM
(permalink)
Very disappointed!!!
With the last two or three bios updates...my REV 1.0 board does a double power down on bootup...one short one second power down and then on for two and down for another two seconds or so. Back to SZ27 for me...not sure when this exactly happened...but for me the last three updates...can't seem to graduate from SZ27...
Double boot at stock speeds...overclocked speeds...
MSI MAG X670-E Tomahawk; Ryzen 7 7800X3D; Asus TUF RTX 4070 TI OC; Seasonic Vertex GX-1000 PSU; 32 GB Corsair Vengeance DDR5-6000 CL30 RGB; Corsair iCue Link H150i LCD 360MM AIO; 2-Western Digital Black 4 TB SN850X NVMe; Creative SoundBlaster Z; Lian Li Lancool III; Corsair K70 RGB Pro MX Speed Silver Keyboard; Razer Viper 8K Mouse
Heatware: https://www.heatware.com/u/72402 Affiliate code: 1L2RV0BNQ6 Associate Code: UD82LJP3Y1FIQPR
|
Nereus
Captain Goodvibes
- Total Posts : 18192
- Reward points : 0
- Joined: 4/10/2009
- Location: Brooklyn, NYC.
- Status: offline
- Ribbons : 58
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 3:58 PM
(permalink)
markgrant
EVGATech_JacobF
Does it say 1.0 or 1.1 on your board?
where is this located?
bottom left hand side of board, written right near the edge by the lower-most pci slot.
|
EVGA_JacobF
EVGA Alumni
- Total Posts : 11559
- Reward points : 0
- Joined: 1/17/2006
- Location: Brea, CA
- Status: offline
- Ribbons : 26
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 5:33 PM
(permalink)
rottenmutt
rev 1.0
any new info on the dreaded S3 support?
This has already been fixed, please contact me directly at jacobf@evga.com
|
EVGA_JacobF
EVGA Alumni
- Total Posts : 11559
- Reward points : 0
- Joined: 1/17/2006
- Location: Brea, CA
- Status: offline
- Ribbons : 26
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 5:34 PM
(permalink)
bobmitch
Very disappointed!!!
With the last two or three bios updates...my REV 1.0 board does a double power down on bootup...one short one second power down and then on for two and down for another two seconds or so. Back to SZ27 for me...not sure when this exactly happened...but for me the last three updates...can't seem to graduate from SZ27...
Double boot at stock speeds...overclocked speeds...
I just confirmed, newer BIOS's had this changed to improve overclocking stability.
|
EVGA_JacobF
EVGA Alumni
- Total Posts : 11559
- Reward points : 0
- Joined: 1/17/2006
- Location: Brea, CA
- Status: offline
- Ribbons : 26
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 5:35 PM
(permalink)
hnic4life
why is it when I go to click those links to start my download... I get a error page everytime
Are you using Chrome browser?
|
Bobmitch
CLASSIFIED ULTRA Member
- Total Posts : 7822
- Reward points : 0
- Joined: 5/7/2007
- Status: offline
- Ribbons : 49
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 6:00 PM
(permalink)
EVGATech_JacobF
bobmitch
Very disappointed!!!
With the last two or three bios updates...my REV 1.0 board does a double power down on bootup...one short one second power down and then on for two and down for another two seconds or so. Back to SZ27 for me...not sure when this exactly happened...but for me the last three updates...can't seem to graduate from SZ27...
Double boot at stock speeds...overclocked speeds...
I just confirmed, newer BIOS's had this changed to improve overclocking stability.
So Jacob...what you are saying is that the double power down is normal? If so...I will reflash... Thanks Bob
MSI MAG X670-E Tomahawk; Ryzen 7 7800X3D; Asus TUF RTX 4070 TI OC; Seasonic Vertex GX-1000 PSU; 32 GB Corsair Vengeance DDR5-6000 CL30 RGB; Corsair iCue Link H150i LCD 360MM AIO; 2-Western Digital Black 4 TB SN850X NVMe; Creative SoundBlaster Z; Lian Li Lancool III; Corsair K70 RGB Pro MX Speed Silver Keyboard; Razer Viper 8K Mouse
Heatware: https://www.heatware.com/u/72402 Affiliate code: 1L2RV0BNQ6 Associate Code: UD82LJP3Y1FIQPR
|
Zigmeister
New Member
- Total Posts : 1
- Reward points : 0
- Joined: 4/11/2009
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 6:48 PM
(permalink)
Just flashed to this bios... worked great.
Thanks
|
zoltanthegypsy
SSC Member
- Total Posts : 721
- Reward points : 0
- Joined: 5/22/2009
- Location: Bainbrige Island, WA, USA
- Status: offline
- Ribbons : 3
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 7:37 PM
(permalink)
iai290
How about, when are we going to get a changelog that says "Hauppauge tv tuners finally work with this motherboard"
Hmmm, My HVR 1250 seems to be working fine. What problems are you having? Z.
|
Dragonshadow
New Member
- Total Posts : 38
- Reward points : 0
- Joined: 11/7/2009
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 8:40 PM
(permalink)
Is there any reason at all to update my bios since I don't have anywhere near that size of partition? I mean my largest drive is 1tb...
|
louy1
New Member
- Total Posts : 94
- Reward points : 0
- Joined: 11/9/2007
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 10:22 PM
(permalink)
So this is for 2 tb drives and no other benifit to flash bios?
EVGA x299 FTWK; Intel Core i7-7820X Processor; e EVGA GeForce RTX 3080 FTW3 ULTRA GAMING ;Corsair Dominator Platinum 16GB (4x4GB) DDR4 DRAM 3200MHz;Corsair Hydro Series H115i Pro RGB AIO Liquid CPU Cooler; EVGA Super NPVA 1000 G3, 80 Plus Gold 1000W;SAMSUNG 970 EVO M.2 2280 250GB PCI Gen3.X4;Samsung 840 EVO 250GB SSD;Windows 10 Home
|
lam_das
iCX Member
- Total Posts : 266
- Reward points : 0
- Joined: 6/8/2009
- Status: offline
- Ribbons : 1
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 11:46 PM
(permalink)
EVGATech_JacobF
lam_das
When are we going to be delighted with a Changelog saying "S3 issues finally fixed...:)"... EVGA, please delight us! We paid you $300 for this board! Gave you a good name for good customer service all over the net!
Let me know if you have forgotten what S3 issues we are facing. They are documented in the archive, under every BIOS released since the beginning of time. But lastly, they were all documented in SZ2P thread.
Does it say 1.0 or 1.1 on your board?
I have rev 1.1 board. So, my S3 issues are not even related to rev 1.0, where S3 was completely screwed up.
EVGA X58 SLI Rev 1.1 i7 920 D0 LinX/Prime Stable 4.4(21x210) HT ON 1.3125vcore, +100mV, vDIMM 1.625v, Rest Auto OCZ Gold 6GB 1680 (2:8) 9 9 9 24 1T Prolimatech Megahalems (Push/Pull) Because of S3 issues: 21x196, Auto vcore, 2:8, 8-8-8-24-1T 12GB.
|
crantana
New Member
- Total Posts : 22
- Reward points : 0
- Joined: 3/14/2009
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Tuesday, November 10, 2009 11:55 PM
(permalink)
don't know what's goin on, but, I can't even post a 3.5 with this bios....was 4.2 before
Antec 1200 Classified 760 i7 920 D0 @ 4.0, 1.27Vcore 6Gb G. Skill Perfect Storm 2000Mhz Cas 8 @ 1833 7-7-7-18 2 x eVGA GTX 260 Core 216 2 x WD 500GB Blacks in RAID 0 WD SE16 320GB WD 500GB My Book external Antec CP-850 psu Asus VW266H Dell 1907fp LG 22x DVD Logitech G9 Custom Loop Belkin n52 Novint Falcon (love that thing) Windows 7 Ultimate
|
crantana
New Member
- Total Posts : 22
- Reward points : 0
- Joined: 3/14/2009
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Wednesday, November 11, 2009 0:21 PM
(permalink)
after 20 minutes, I got it all back.....still don't know what happened...oh well, all is good
Antec 1200 Classified 760 i7 920 D0 @ 4.0, 1.27Vcore 6Gb G. Skill Perfect Storm 2000Mhz Cas 8 @ 1833 7-7-7-18 2 x eVGA GTX 260 Core 216 2 x WD 500GB Blacks in RAID 0 WD SE16 320GB WD 500GB My Book external Antec CP-850 psu Asus VW266H Dell 1907fp LG 22x DVD Logitech G9 Custom Loop Belkin n52 Novint Falcon (love that thing) Windows 7 Ultimate
|
iai290
New Member
- Total Posts : 69
- Reward points : 0
- Joined: 12/13/2008
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Wednesday, November 11, 2009 0:54 PM
(permalink)
zoltanthegypsy
iai290
How about, when are we going to get a changelog that says "Hauppauge tv tuners finally work with this motherboard"
Hmmm,
My HVR 1250 seems to be working fine. What problems are you having?
Z.
The same problem almost every other owner is having with the 1800/1850.. It just isn't detected. Which means drivers don't install and the card doesn't work.
post edited by iai290 - Wednesday, November 11, 2009 3:24 AM
|
Luigi408
iCX Member
- Total Posts : 331
- Reward points : 0
- Joined: 8/28/2005
- Location: San Jose, Ca
- Status: offline
- Ribbons : 0
Re:EVGA X58 SLI (E758) - SZ2X BIOS Released
Wednesday, November 11, 2009 11:23 AM
(permalink)
iai290
zoltanthegypsy
iai290
How about, when are we going to get a changelog that says "Hauppauge tv tuners finally work with this motherboard"
Hmmm,
My HVR 1250 seems to be working fine. What problems are you having?
Z.
The same problem almost every other owner is having with the 1800/1850.. It just isn't detected. Which means drivers don't install and the card doesn't work.
I have a problem with my tv tuner also but in my Classified motherboard. My tv tuner is avermedia and it locks up my pc when Windows starts, card works fine with my 780i. I just sent Jacob my tv tuner card for testing with my Classified, I have been talking and calling EVGA about it since Classified was released! Email Jacob and keep bugging him about it and send him your tv tuner card for testing because there seems to be something wrong with these motherboards. If he doesn't asnwer you call EVGA and ask to talk to the highest ranking person. I got help once I started getting upset and asking to talk to someone higher than the normal customer service rep after many many months of not really been helped. I have been following up with Jacob about my tv tuner problem and he seems like he is going to help me out with mine so email him and maybe send him your card for testing. Good luck. I'll post my status about it in the forums once they finish debuging it, my card should arrive at Jacob's office tomorrow.
|