Go to our old forum archive and copy the X58 template. Fill it out with your values and post it here:
 
http://forums.evga.comarchive/tm.asp?m=100548328

Edit: I didn't uninstall e-leet before biosflash, could that cause all my problems afterwards?
Edit 2: Solved!!!! Did a reflash, Left rams settings @ auto, MCH strap-> auto, timings @ 9-9-9-24-88 t2 and a boot @ 21x200, prime stable for 1h and counting.. with 6gb mem. Think MCH strap was the problem, wel.... When i left my memtimings @ auto with low bclk (165 max), it detected right settings-> 9-9-9, but when bclk hits above 170 the timing automatic went down to 8-8-8. Had to set the timings fixed as above and finaly got a boot... Felt like a childbirth, long and heavy, but a nice result non the less :) (sorry for my english btw, im a dutch bloke, so my grammar sux more than al little)
 
Some specs i filled in double, tried both! Thnx for the help
 
Mother Board ( EVGA X58 Classified E-760 ) 
Drivers ( 1024 )  Save Change
Bios (77) 
CPU ( 950 d0 ) 
CPU Cooler ( H50 push pull ) 
Memory ( Corsair 1600 xms c9 ) 
PSU ( CMmsilent pro 1000w) 
GPU ( GTX470 sli) 
Drivers ( 262.99 ) 
Operating System ( Windows 7 64 Ultimate ) 


Frequency Control 
CPU Clock Ratio ( 23X/21x ) 
CPU Host Frequency (Mhz) ( 180/200 ) 
MCH Strap ( 1600/auto ) 
CPU Uncore Frequency (Mhz) ( auto ) 
CPU Clock Skew ( 0 ps ) 
Spread Spectrum ( Disabled ) 
PCIE Frequency (Mhz) ( 105 ) 


Memory Feature         
Memory Speed ( normal ) 
Memory Control Setting ( Enabled ) 
Memory Frequency ( auto 1600 ) 
Channel Interleave Setting ( 6 Way ) 
Rank Interleave Setting ( 4 Way ) 
Memory Low Gap ( Auto ) 
tCL Setting ( 9 ) 
tRCD Setting ( 9 ) 
tRP Setting ( 9 ) 
tRAS Setting ( 24 ) 
tRFC Setting ( 88 ) 
Command Rate ( 2t ) 


Voltage Control 
EVGA VDroop Control ( Without VDroop ) 
CPU VCore ( 1.375 ) 
CPU VTT Voltage ( +200 ) 
CPU PLL VCore ( auto ) 
**IOH PLL VCore ( auto )  
DIMM Voltage ( 1.65 ) 
DIMM DQ Vref ( +0mV ) 
QPI PLL VCore ( 1.3 ) 
IOH VCore ( auto ) 
IOH/ICH I/O Voltage ( Auto )    
**VTT PWM Frequency ( 250 KHZ ) 
**CPU PWM Frequency ( 800 KHZ ) 
**CPU Impedance ( auto) 
**QPI Signal Compensation ( More ) 
ICH VCore ( Auto ) 
*PWM Frequency ( Not Used on Classified ) 


CPU Feature 
Intel SpeedStep ( Disabled ) 
Turbo Mode Function ( disabled ) 
CxE Function ( Disabled ) 
Execute Disable Bit ( Disabled ) 
Virtualization Technology ( Disabled ) 
Intel HT Technology ( Enabled ) 
Active Processor Cores ( All ) 
QPI Control Settings ( Enabled ) 
QPI Link Fast Mode ( Enabled ) 
QPI Frequency Selection ( auto ) 
OC Recorvery ( Enabled ) 

I finally located the problem! Somehow my ram (TR3X6G1600c9) is not supported. With ocz memory tested and the problems were gone. Even tested with a 920 and my ram and the problems stayed, so i think i need a new set of ram. Its weird cause my corsairs worked fine with the Gigabyte mobo @ 1740Mhz. Well, im glad it's not the classie, i'll post new results when new ram is here.
 
Thnx 4 the support peepz!