So WildDog and I have been working on getting my new rig stable at 4.2.  I tried everything that he has suggested which was all helpful but i can't seem to get anywhere else.  I'm totally new to the X58 series and I have read all the overclocking guides.  I'm still reading and rereading but I really want to get this thing up and folding ASAP!
 
Here is what I'm at thus far:

 

 

 

 

 
As far as stability testing I'm using LinX and IBT.  I don't think Prime95 cuts it anymore with the X58 series!

Yeah, your Vcore is a little low.  I would up it to 1.37 and work down from there.  QPI PLL needs to go up to 1.25.  CPU VTT is to high try to bring it down to 1.25 ish volts.  Try running the CPU PLL at 1.65v.  Again Vcore needs to come up quite a bit.  Try Dram ratio of 1600mhz and make sure uncore is set to 16x 3200mhz ish.  You should be good after that.  Looks like your very close since the shots are taken from windows and that means your at least getting into it.
 
Also their going to ask for a bios template - they always do - so you might want to post one.
Also what BSOD's are you getting?
 
P.S.  Keep in mind that Eleet is about as acurate as carpet bombing.  The voltages it shows, especially under load, are wrong!!  They can be off by quite a bit.  What you set in bios is what you get.  I've done tests with fluke meters and if you set 1.35v in bios you will get 1.35 volts in windows.  If you switch to without vdroop then it will ONLY go up .2 volts NO MATTER what Eleet says.  From the Fluke meter I got 1.37 volts at 100 percent load (bios setting 1.35V) and 1.42V from Eleet!!!!

Thats a software/driver issue. Has nothing to do with your OC.
If it was your OC you would be getting force restarts / blue screen.
 
 
(Correct me if i'm wrong please)

Well I reran LinX and BOSD 0x101!

Here is what I got with VCORE increase:

 
During test before it failed:

I needed 1.375 VCore on mine. , your Vtt is only .02 lower than mine. However since every chip is difrent, What mine needed does not predict what yours will, also not every chip will do 4.2, my 920 will do it all day long, and I only paid $200 for it, ( Micro Center)  My 965 will not run stable above 4.0, ( wish I had known ) could have saved about $500.

Well I passed LinX.  VREG still hit around 80-85c.  I was able to put a fan on it so I'm not sure yet the improvement.

 

 
 

i would set the uncore speed manually. I might even add a touch of vtt. Your overclock looks very nice though.

The new BIOS setup looks pretty good.  You may want to bump up the ICH voltage a bit if you run into any unstable behavior in Windows. I know when I had my processor at bclk 221, that my USB ports including the mouse would start acting up.
 
If you do start seeing crashes while running Prime95 or LinX, I would suggest backing down the CPU multiplier to 17x temporarily in order to get the bclk stable first.

Did you get a BSOD or did linx error out?
 
You may also be able to lower your VTT some since you went back to bclk 200. Try +150mv.

BSOD with setting VTT to +150.  I got IRQL_NOT_LESS_OR_EQUAL.
 
I think that means that I need to increase VTT doesn't it?

I just saw you were attempting this again, any updates on what linuxrouter suggested^?

Well no luck going +200.  Error on first pass!  Not too sure what to do other than adding VTT!

I'm hitting high 70's under LinX!  While folding I'm in the low 70's.
 

  I added +25 but have done anything yet.  Waiting for your response before I proceed!

 

Alright I'll give 196 bclk a go.  Do I need to leave all other voltages were they are?