This one is better

Hey awall, don't wanna spam your PM box, but the most recent settings are good up to 21x209, at 210 it just froze.

halo its your RAM/PLL both too high for water cooling.

What should they be at?

Tribbs

http://kingpincooling.com/forum/showthread.php?t=1089

Saw this over in the enemy's camp  and may have to try it out, may have to modify my blockman special to do it, and i wish that kingpin would hurry up and finish that dice base for the gemini, ive been itching to get one.  

You know, a while back I was looking for a PCI-E extension to do that very same thing. 

well hey there reggie.
 
yeah, that's a good one awall..
 
 
nate,
yeah i remember that as well.
 
tribbs,
i too am waiting on that dice block attachment and will probably add the top extension as well.

Try and do one thing at a time.
Core
Uncore
Ram
When finding your core clock lower your uncore speed and ram speed. Also loosen your ram timings. And hop on the 2/6 ratio. There is a pretty good chance that you cant do 4.6 on water. Try and keep your pll @1.35-1.4 Then start testing according to temp if your idleing past 38 than you need more cold for most benches. The 930 I have now wont let me bench vantage past 4.4ish on water, and I can only hit past 2ghz ram @ 3.6 or so.

 I agree with reggie.

Was benchable at 4.5 before, just lost my settings lol..
 
Frequency Control    
CPU Clock Ratio ( 21X )    
CPU Host Frequency (Mhz) ( 209 )    
MCH Strap ( 1600 )    
CPU Uncore Frequency (Mhz) ( Auto )    
CPU Clock Skew ( 0 ps )    
Spread Spectrum ( Disabled )    
PCIE Frequency (Mhz) ( 102 )    


Memory Feature            
Memory Speed (Standard)    
Memory Control Setting ( Enabled )    
Memory Frequency ( 800Mhz / 2:6 )    
Channel Interleave Setting ( 6 Way )    
Rank Interleave Setting ( 4 Way )    
Memory Low Gap ( Auto )    
tCL Setting ( 6 )    
tRCD Setting ( 7 )    
tRP Setting ( 6 )    
tRAS Setting ( 18 )    
tRFC Setting ( Auto )    
Command Rate ( 1t )    


Voltage Control    
EVGA VDroop Control ( Without VDroop )    
CPU VCore ( 1.5125 )    
CPU VTT Voltage ( +150 )    
CPU PLL VCore ( 1.905 ) <-- just for testing purposes currently..   
**IOH PLL VCore ( 1.500 )     
DIMM Voltage ( 1.65 )    
DIMM DQ Vref ( +0mV )    
QPI PLL VCore ( 1.350 )    
IOH VCore ( 1.150V )    
IOH/ICH I/O Voltage ( 1.500V )    
**BR04 ( NF200) Voltage ( Auto ) (only on E-759)    
**VTT PWM Frequency ( 610 KHZ )    
**CPU PWM Frequency ( 1210 KHZ )    
**CPU Impedance ( Less )    
ICH VCore ( 1.1000 )    
DDR Signal 0:  ( -31 )  
DDR Signal 1:  ( -31 )  
DDR Signal 2:  ( -31 )  
CPU Signal:  ( -62 )  
QPI Signal 0:  ( -62 )  
QPI Signal 1:  ( -30 )  
QPI Signal 2:  ( -31 )  
PCIE Signal 0:  ( -20 )  
PCIE Signal 1:  ( -20 )  
   

CPU Feature    
Intel SpeedStep ( Disabled )    
Turbo Mode Function ( Disabled )    
CxE Function ( Disabled )    
Execute Disable Bit ( Disabled )    
Virtualization Technology ( Disabled )    
Intel HT Technology ( Enabled )    
Active Processor Cores ( All )    
QPI Control Settings ( Enabled )    
QPI Link Fast Mode ( Enabled )    
QPI Frequency Selection ( 4.800 GT/s )    
OC Recorvery ( Disabled )   

Perhaps you just have a voltage hog there.