I was hoping someone might be able to give a little help I'm stuck at 208 blck. Can't seem to find any combination of volts to be stable.
I boot in to windows at 200 blck, bold print shows the changes I've tried in Eleet. Any tweaks or tips would be great!

Mother Board ( EVGA X58 Sli  E758-A )                                                       
Bios ( ? )                                                                                                     
 CPU ( 920 D0)              
CPU Cooler ( Chiller 70-80f )
Memory ( Gskill Trident 16000 7-8-7 22 1t )
PSU ( Corsair HX1000W )
GPU ( 9800 GT but swap everyday )
Drivers ( 190.56 )                                                                                                  
Operating System W7 Pro / Xp Pro

CPU Clock Ratio ( 20X )
CPU Host Frequency (MHz) ( 200 ) ----- 208
MCH Strap (1600)
CPU Uncore Frequency (MHz) ( 16x )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 106 )
Turb Performance (Enable)
Extreme Cooling (Mode 1)

Memory Feature
Memory Control Setting ( Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Parameters
tCL Setting ( 7 )
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 22 )
tRFC Setting ( 88 )
Command Rate ( 1T )

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.4 ) ------ up to 1.55
CPU VTT Voltage ( +400 )
CPU PLL VCore ( 1.800 ) ----- Eleet says 1.45
DIMM Voltage ( 1.675 ) -------- up to 1.725     
DIMM DQ Vref ( +0 )
QPI PLL VCore ( 1.425 ) -------- up to 1.55
IOH VCore ( 1.4 ) ------ up to 1.5
IOH/ICH I/O Voltage ( 1.65 )
ICH VCore ( 1.25 ) ------  up to1.4
PWM Frequency ( 1067 )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Logical Processor Setting
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Settings
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.8 GT/s )

Maximum Payload Size (4096)

threedhero

I was hoping someone might be able to give a little help I'm stuck at 208 blck. Can't seem to find any combination of volts to be stable.
I boot in to windows at 200 blck, bold print shows the changes I've tried in Eleet. Any tweaks or tips would be great!

Mother Board ( EVGA X58 Sli  E758-A )                                                       
Bios ( ? )                                                                                                     
CPU ( 920 D0)              
CPU Cooler ( Chiller 70-80f )
Memory ( Gskill Trident 16000 7-8-7 22 1t )  Loosen this up
PSU ( Corsair HX1000W )
GPU ( 9800 GT but swap everyday )
Drivers ( 190.56 )                                                                                                  
Operating System W7 Pro / Xp Pro

CPU Clock Ratio ( 20X )
CPU Host Frequency (MHz) ( 200 ) ----- 208
MCH Strap (1600)  Either leave on auto or go for 1866 1866 will lesson performance a bit but help stabilize I think.
CPU Uncore Frequency (MHz) ( 16x )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 106 )
Turb Performance (Enable)  Disable this it is mainly for the 6 core processors.
Extreme Cooling (Mode 1)  leave at default does not seem to do much (maybe I am wrong)

Memory Feature
Memory Control Setting ( Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Parameters
tCL Setting ( 7 )  Just try these at auto for now, can tighten up later
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 22 )
tRFC Setting ( 88 )
Command Rate ( 1T )

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.4 ) ------ up to 1.55  These chips do not like to much either
CPU VTT Voltage ( +400 )  No reason to be so high here try +200 to +250 max
CPU PLL VCore ( 1.800 ) ----- Eleet says 1.45  for a 920 DO 1.425 to 1.5 is good
DIMM Voltage ( 1.675 ) -------- up to 1.725   Way too much here put at factory settings    
DIMM DQ Vref ( +0 )
QPI PLL VCore ( 1.425 ) -------- up to 1.55  Way to high try 1.3
IOH VCore ( 1.4 ) ------ up to 1.5  all this is for is video cards mostly if to high messes with everything.
IOH/ICH I/O Voltage ( 1.65 )  up 1 for every 2 in IOH vcore
ICH VCore ( 1.25 ) ------  up to1.4  basically for hardrives no need to be so high 1.1 should be plenty
PWM Frequency ( 1067 )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Logical Processor Setting
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Settings
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.8 GT/s )

Maximum Payload Size (4096)

   Thats all I got.

threedhero

I was hoping someone might be able to give a little help I'm stuck at 208 blck. Can't seem to find any combination of volts to be stable.
I boot in to windows at 200 blck, bold print shows the changes I've tried in Eleet. Any tweaks or tips would be great!

Mother Board ( EVGA X58 Sli  E758-A )                                                       
Bios ( ? )                                                                                                     
CPU ( 920 D0)              
CPU Cooler ( Chiller 70-80f )
Memory ( Gskill Trident 16000 7-8-7 22 1t )
PSU ( Corsair HX1000W )
GPU ( 9800 GT but swap everyday )
Drivers ( 190.56 )                                                                                                  
Operating System W7 Pro / Xp Pro

CPU Clock Ratio ( 20X )
CPU Host Frequency (MHz) ( 200 ) ----- 208
MCH Strap (1600) DRAM RATIO FOR NOW
CPU Uncore Frequency (MHz) ( 16x )  AUTO FOR NOW
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 106 )
Turb Performance (Enable)
Extreme Cooling (Mode 1)

Memory Feature
Memory Control Setting ( Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Parameters
tCL Setting ( 7 )
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 22 )
tRFC Setting ( 88 )
Command Rate ( 1T )

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.4 ) ------ up to 1.55   1.47 FOR NOW
CPU VTT Voltage ( +400 )
CPU PLL VCore ( 1.800 ) ----- Eleet says 1.45   IT IS READING THAT BECAUSE YOU SET MODE 1 IN THE BIOS
DIMM Voltage ( 1.675 ) -------- up to 1.725     DROP THIS BACK TO 1.65 UNLESS YOUR RUNNING MORE THAN 6 GIGS 
DIMM DQ Vref ( +0 )
QPI PLL VCore ( 1.425 ) -------- up to 1.55 1.375 FOR NOW
IOH VCore ( 1.4 ) ------ up to 1.5
IOH/ICH I/O Voltage ( 1.65 ) COOL FOR NOW
ICH VCore ( 1.25 ) ------  up to1.4 1.30 FOR NOW
PWM Frequency ( 1067 )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Logical Processor Setting
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Settings
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.8 GT/s )

Maximum Payload Size (4096)

Depending on what your ram is when trying to boot...you may need to drop the divider to 2:10 then work your way back to 2:8.
this is just to try and get you booting and up to 220...that's if you have a water chiller and that water chiller is set to like 50 to 60F else you can run where your at...at like 218 or so.

damn awall....we look pretty close on settings...lol

 Yeah but going from 2:8 to 2:10?

awalleyeguy

 Yeah but going from 2:8 to 2:10?

facepalm! 
lol


your right
not sure what i was thinking there...hahaha

Haha sweet thanks for the tips guys, I've been racking my brain with voltages for the last few weeks. Everything looks really insightful can't wait to give it ago! More hw points for the team right?!?!

The reason for the crazy memory is I saw shammy running at almost the same setting with the same kit. He was at 930mhz with 1.8 volts. Guess I was feeling like superman for a moment.

are you running a fan on your memory?

Well its a desktop Pc ATM and was doing a few runs in wprime at 1.75v but no I don't have a fan over ram. Looking like i'm being taken to school lol which is cool cus I'm all ears.

Alright question is it going to be better for me to boot in at a higher blck? What I'm doing atm is booting in at 200blck and working my way up in eleet. So far wprime bsods at 212blck